How to Fix a Flooded Engine on a Whipper Snipper
- Turn the switch on to the run position.
- Move choke lever to the run position.
- Press the throttle trigger while pulling the starter rope over and over. This can take anywhere between 5 and 15 pulls before it starts. Your whipper snipper engine will sputter first. Continue to pull a few more times and it should start.
Why won't my brush cutter start?
What to do when you remove a tank cap?
How to clean spark plugs that are dirty?
Why does my brush cutter keep cutting out?
Do you need to wind a string on a cutting machine?
Why is my whipper snipper not working?
A dirty spark plug If the central electrode is covered in dirt this can short out the spark so that it won't jump to the outer electrode, which will mean you will struggle to start the whipper snipper – you can clean the dirt off with a tooth brush, or small wire brush.
Why is my strimmer not starting?
The most common problem with a strimmer not starting is that there's a problem with the fuel mix. Double check that you've used 40 parts fresh unleaded petrol to 1 part 2-stroke oil (40:1). Check the petrol you've used isn't stale.
Why is my line trimmer not working?
If the carburetor is clogged, try cleaning it with carburetor cleaner. If cleaning the carburetor isn't effective, rebuild or replace the entire carburetor. The carburetor might be clogged. A clogged carburetor is most commonly caused by leaving fuel in the string trimmer for a long period of time.
How do you know if a whipper snipper is flooded?
Start a warm engine on a Weed Eater without engaging the choke to avoid flooding the carburetor. The telltale sign of a flooded engine is the strong scent of gasoline and no fire from the spark plug.
How do you start a 2 stroke whipper snipper?
0:272:10McCulloch - How to start a two stroke trimmer engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipSome of our engines need a full choke setting during the starting procedure set the choke at the maxMoreSome of our engines need a full choke setting during the starting procedure set the choke at the max position and pull the starting cord until the engine fires.
How do you start a petrol whipper snipper?
1:204:53How to start a trimmer with a 2 stroke engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition. Before you start your machine cold or warm you must press the primer bulb of the fuel pumpMorePosition. Before you start your machine cold or warm you must press the primer bulb of the fuel pump fully at least six times our products are fitted with three different kinds of chokes.
How do you Unflood a trimmer?
Try these steps to unflood the engine on a Trimmer/Brushcutter/Edger (SRM/GT/PAS/PE) model;Check on/off switch. ... Choke lever must be put in the run position (choke open position/down). ... Depress the purge bulb until fuel enters the bulb and the fuel returns back to the fuel tank through the clear line.More items...•
How do you start a string trimmer?
1:464:18Starting a Gas String Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to place the choke lever to the cold start position on a cold start you push the purgeMoreYou want to place the choke lever to the cold start position on a cold start you push the purge valve five to six times making sure that it's filled with fuel. So now you're ready to pull the recoil.
How do you fix a string trimmer?
0:102:19Replacing a Weed Eater String (String Trimmer Line) - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure it's powered off and clean up dirt and debris remove. The bump knob and spool by pushingMoreMake sure it's powered off and clean up dirt and debris remove. The bump knob and spool by pushing the tabs on the sides of the trimmer.
How long to wait if engine is flooded?
If the car doesn't start after 15 seconds, stop and wait a couple of minutes, to let the starter motor cool down, and crank again. If you just continue cranking past 15 seconds until the engine starts or the battery dies, you may overheat or damage the starter.
How do you Unflood a 2 stroke engine?
0:417:02HOW-TO Quickly Un-flood An Engine! - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe throttle wide open and then pull it over until it finally starts. This simple method of turningMoreThe throttle wide open and then pull it over until it finally starts. This simple method of turning the choke off and holding the throttle.
What causes a small engine to flood?
Most commonly a result of improper starting, "flooding" results from various causes, including over-priming, closed choke, stuck valve, gummed carburetor, or immediately trying to restart an automatic choke engine. The easiest way to tell if your engine is flooded with gas is to remove the spark plug.
Why does my petrol strimmer start then cut out?
If the carburetor is clogged, try cleaning it with carburetor cleaner. If cleaning the carburetor isn't effective, rebuild or replace the entire carburetor. The carburetor might be clogged. A clogged carburetor is most commonly caused by leaving fuel in the string trimmer for a long period of time.
How do you adjust a strimmer carburetor?
4:1411:56Tuning a carburetor on a trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can see two round screws the one closer to the engine is labeled l and it's for low engine speedMoreYou can see two round screws the one closer to the engine is labeled l and it's for low engine speed adjustments. And the screw closer to the air filter is labeled h.
How do you start a trimmer engine?
1:454:08String Trimmer Basics: String Trimmer Fueling and Starting - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to place the choke lever to the cold start position on a cold start you push the purgeMoreYou want to place the choke lever to the cold start position on a cold start you push the purge valve five to six times making sure that it's filled with fuel. So now you're ready to pull the recoil.
Why does my Stihl trimmer not start?
If you've used the correct procedure to start your Stihl trimmer and it does not start, the problem is likely related to either the spark, the fuel or the air circulation in the combustion chamber. More often than not, it's an easy fix, possibly involving replacement of a spark plug or air filter.
Why won't my brush cutter start?
You go out to start your brush cutter, weed whacker, or string trimmer and it won't start. If you've tried a few times and it still won't start, and you smell gasoline, you've probably flooded it. Wait about 10 minutes before you try again to give the gasoline time to evaporate.
What to do when you remove a tank cap?
When you remove the cap, don't allow sand, cut grass, or anything to enter your tank. Work cleanly to avoid any potential problems down the road. If necessary, take a small sheet of plastic or cloth to put the machine on. You'll likely have tiny particles of grass or debris on your gloves.
How to clean spark plugs that are dirty?
If your spark plug is dirty, use a fine emery paper to remove any deposits around the electrodes. If you have a gapping tool that measures the distance, it should be 0.02 inches (0.5mm) in a spark plug. If the gap is too large, use a pair of pliers to minimize the space. Other brands of brush cutters may have a different recommended gap, so check your manual.
Why does my brush cutter keep cutting out?
This too can be caused by problems with your carburetor. Follow the guidelines above in the video and in your manual to find the perfect balance of air/gas for your machine.
Do you need to wind a string on a cutting machine?
Now that you have got your machine working again, you'll need to wind your string on. If you're serious about your cutting and maintaining your machines, rewinding your string is something you'll need to learn.
What to do if your whipper snipper starts and stops?
If your engine is trying to run, or starts and quickly stops, you might want to do a quick air filter check. You need air for your initial spark – and if oxygen cannot move readily through the system you will have problems both starting and keeping your whipper snipper running.
Why won't my carburetor seal?
If the material of the primer bulb has deteriorated, it is likely that it won’t seal properly against the body of the carburettor. This will result in an air leak which will prevent the bulb sucking up fuel and causing starting issues.
What is a whipper snipper?
Whipper snippers, or as some refer to them – weed whackers, weed eaters, line trimmers, brush cutters or trimmers – whatever you call them when they don’t start they can be one of the most frustrating garden tools in the shed.
What can short out a spark plug?
A dirty spark plug. If the central electrode is covered in dirt this can short out the spark so that it won’t jump to the outer electrode, which will mean you will struggle to start the whipper snipper – you can clean the dirt off with a tooth brush, or small wire brush.
Why won't my brush cutter start?
You go out to start your brush cutter, weed whacker, or string trimmer and it won't start. If you've tried a few times and it still won't start, and you smell gasoline, you've probably flooded it. Wait about 10 minutes before you try again to give the gasoline time to evaporate.
What to do when you remove a tank cap?
When you remove the cap, don't allow sand, cut grass, or anything to enter your tank. Work cleanly to avoid any potential problems down the road. If necessary, take a small sheet of plastic or cloth to put the machine on. You'll likely have tiny particles of grass or debris on your gloves.
How to clean spark plugs that are dirty?
If your spark plug is dirty, use a fine emery paper to remove any deposits around the electrodes. If you have a gapping tool that measures the distance, it should be 0.02 inches (0.5mm) in a spark plug. If the gap is too large, use a pair of pliers to minimize the space. Other brands of brush cutters may have a different recommended gap, so check your manual.
Why does my brush cutter keep cutting out?
This too can be caused by problems with your carburetor. Follow the guidelines above in the video and in your manual to find the perfect balance of air/gas for your machine.
Do you need to wind a string on a cutting machine?
Now that you have got your machine working again, you'll need to wind your string on. If you're serious about your cutting and maintaining your machines, rewinding your string is something you'll need to learn.
