what do you need to hang sheetrock

You should, at a minimum, have:

Full Answer

Can anyone hang drywall?

Learning how to install drywall is very much within the reach of the average DIY enthusiast. With patience, the right tools and a friend to help you, hanging drywall is not very difficult. Once you've learned how to hang drywall, learn how to tape and finish the installed drywall for professional-quality results.

Is it better to use nails or screws for Sheetrock?

Drywall screws provide a stronger hold, but cost a bit more than nails. When choosing drywall screws vs. nails, consider the size of your project and the materials you'll be using. Use screws instead of nails when you are working on a ceiling installation or working with metal studs or frames.

What is the process for hanging drywall?

How to Hang DrywallPrepare the Drywall Sheets for the Ceiling. ... Install Drywall on the Ceiling. ... Measure and Cut Drywall for the Wall. ... Install Drywall on the Wall. ... Cut Openings for Doors, Windows and Outlet Boxes. ... Secure the Drywall Against the Outside and Inside Corners. ... Add the Finishing Coats of Drywall Compound.

How do you hang sheetrock by yourself?

1:032:59How to Cut & Hang Drywall By Yourself - 15 Beginner Sheetrock TipsYouTubeStart of suggested clipEnd of suggested clipYou can use framing nails to help you hang drywall by yourself like i am here just lightly tap themMoreYou can use framing nails to help you hang drywall by yourself like i am here just lightly tap them into place you don't want to sink them all the way.

Whats the difference between sheetrock and drywall?

Drywall is a flat panel made of gypsum plaster sandwiched in between two sheets of thick paper. It adheres to metal or wood studs using nails or screws. Sheetrock is a specific brand of drywall sheet. These terms are often used interchangeably.

What size screws do I need for 1/2 drywall?

1-1/4”Choosing the right drywall screw Most common — 1-1/4”: Use 1-1/4” drywall screws to secure 1/2″ drywall installed on wood-stud walls. These coarse-thread screws typically feature phosphate coatings, which better protect against rust compared to zinc coatings.

How long does it take to drywall a 12x12 room?

Installing drywall in a 12' x 12' room takes 2 to 3 days, including the drying time between each coat of drywall mud.

Should drywall touch the floor?

Always leave a 1/2-inch gap at the floor. This allows for floor and wall expansion without cracking the drywall. It also helps prevents moisture wicking if the floor floods. Wear work gloves, safety goggles and a dust mask when hanging drywall.

Do you have to tape drywall seams?

All drywall seams need to have tape embedded in joint compound. The tape strengthens the joint, and the joint compound, or mud, is the adhesive that holds the tape in place.

Do you drywall ceiling or walls first?

Hanging Drywall From the Top Down Hang drywall on the ceiling first, then the walls. Check the ceiling for bowed joists using a 4-ft. level.

How difficult is it to hang drywall?

It's harder than you think. Drywall work is hard. The hanging of the large, heavy sheets is mind-numbing. If you decide to do it yourself, you can rent or buy mechanical lifts that hold the sheets up to save your back.

How do you hold sheetrock on the ceiling?

3:225:47Amazing Trick To Hang Sheetrock (Drywall) On A Ceiling By Yourself!YouTubeStart of suggested clipEnd of suggested clipSo we're going to pick up the drywall from the bottom. And slide them up the guides. Then we'reMoreSo we're going to pick up the drywall from the bottom. And slide them up the guides. Then we're going to continue to walk it up with the ladder. Until it slides into the slot. Up at the top.

Do people still use nails in drywall?

0:226:15The PROBLEM with DRYWALL NAILS!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm gonna nail all the drywall on and I'm gonna show you the problems that happen from nailing onMoreI'm gonna nail all the drywall on and I'm gonna show you the problems that happen from nailing on drywall. So actually there is one practical place to use them and that's on the bottom of your wall.

Why do people use nails in drywall?

Drywall screws are more secure when installed properly, but drywall nails are much cheaper and, in certain areas, easier to put in.

Why do roofers use nails instead of screws?

Nails are often preferred for structural joining, including framing walls, because they are more flexible under pressure, whereas screws can snap. Nails are also called upon when securing plywood sheathing for exterior walls, installing hardwood floors, and attaching siding and roofing.

Can you use nails on Sheetrock?

1:279:24Drywall Fasteners - Nails vs Screws - Drywall Instruction - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's a not I mean it's not a bad idea it's just not necessary in most cases. Let's talk a little bitMoreIt's a not I mean it's not a bad idea it's just not necessary in most cases. Let's talk a little bit about nails. First we do still use nails. In in drywall. A dry typical drywall nails you can see in

How to finish outside corners?

Outside corners can be easily finished by installing one side of the corner with a slight overhang. Once the panels are fixed in place, simply cut off the bit that sticks out, following the line of the corner, to get a perfect, tight fit. Add a corner bead to protect the raw edges of the corner from damage that can lead to cracking and other expensive repairs.

What is the most common finishing material?

Drywall is the most common interior finishing material because it is inexpensive, easily sourced and most importantly, easy to work with. While finishing drywall as smoothly as a pro takes years of practice, drywall is a DIY-friendly material. If you make some mistakes, rest easy: they can be fixed with a few bucks and relatively little time.

Why hang a ceiling perpendicular?

By hanging them perpendicular, you create more points of attachment along the long axis of the panel which will help avoid sagging ceilings. The downside is that this creates butt joints, which require more skill to finish but a sagging ceiling is a much bigger, more noticeable problem than small finishing mistakes.

Can you hang wall sheets horizontally?

When working in a commercial environment, regulations may require you to hang wall sheets vertically. In residential projects, you typically have the option to hang these sheets horizontally, which offers several benefits: Fewer seams to tape later so less to finish. Ability to hide studs that are bowed or uneven.

Can you hang sheets on drywall?

As you work, you may hang sheets that cover windows, power outlets, or other kinds of fixtures that will need to come through the drywall. The best approach depends on whether the fixture is already in place.

Is sheetrock easier to install than drywall?

If you make some mistakes, rest easy: they can be fixed with a few bucks and relatively little time. Some steps of drywall (or “sheetrock”) installation are easier than others. Generally, the steps require more skill as you move forward in the installation process.

Can you hire a pro to hang rock?

If, on the other hand, hanging the rock feels like a good enough challenge, you can still hire a pro to do the finishing. Just be sure to go carefully – correctly hung drywall makes it easier for the finisher to get good results.

Introduction to Hanging Drywall

Drywall is panels of pressed gypsum plaster between heavy paper. Drywall is also known as plasterboard, wallboard and gypsum board. Some people call it “Sheetrock,” but Sheetrock is a registered trademark of a company that produces drywall.

Prepare Your Room

Cover electrical and plumbing lines with nail protector plates. This prevents accidental drilling or nailing into utility lines. Watch our Video: When Do I Use Nails vs. Screws?

Tape Drywall Seams

Using mesh tape – which hides seams more effectively than paper tape – cover the vertical joints, or butt joints, first, pressing it firmly into place with a drywall knife. Then cover the horizontal seams. Finally, cover the corners.

Joint Compound: Third Coat

The third coat is called the finish coat, which means you should leave no tool marks.

Skim Coat

For a professional finish, apply a skim coat. A skim coat is a thin layer of joint compound or “mud” that camouflages any rough areas left after the final coat of compound.

What is the best thing about drywall?

GeorgePeters / Getty Images. One great thing about installing drywall is that it is so inexpensive. None of the materials will bankrupt you. This is simple stuff: paper, gypsum, metal, screws, and some strips of plastic. You can tear out the existing drywall or plaster/lath in a room and re-wall it inexpensively.

How long is drywall?

But even those pricier materials, at their hearts, are just gypsum sandwiched between two layers of paper. Drywall comes in convenient sheets that are 8 feet long and 4 feet wide.

Why use corner bead?

Outside corners are prone to strikes. Moving a piece of furniture, or even hitting the corner with a coffee mug , can be enough to chip corners. That is why you use corner bead. The secret behind the corner bead is that the outermost edge of your outside corner is a material other than the drywall compound.

Does low dust reduce drywall dust?

If you want to reduce drywall dust, low-dust joint compound will significantly reduce—though not eliminate— those classic far-reaching clouds of drywall dust that will crawl even to the opposite end of the house. Low-dust drywall compound costs about twice as much as regular mud, but many users find the extra cost worthwhile.

Can you join drywall with joint compound?

Until some genius invents a better, cleaner, faster way to join pieces of drywall and cover up holes, you're stuck with joint compound.

Can you tear out drywall?

You can tear out the existing drywall or plaster/lath in a room and re-wall it inexpensively. This cost even factors in your drywall tools but not insulating or running electricity. It is a great feeling to have all-new walls in a room where before you only had crumbling plaster or moldy, saggy wallboard.