What is the best sealant for Penny floors?
If you then seal the floor with either epoxy resin or polyurethane floor sealant the you’ve got a pretty much indestructible floor! Creativity: As you will see below there are all kinds of great creative designs that come into play when laying your penny flooring.
How do you put pennies on a tile floor?
Line up the mesh on top of your new template. Use a dot of glue to adhere each penny to the tile one at a time. You can also pre-glue a small section to make it easier. Push your penny down into the glue on top of the mesh backing. Use the penny template underneath the mesh to guide you. After you’ve finished a full square, let it dry overnight.
What glue do you use to stick pennies to the floor?
I used Krylon Low Odor Spray Glue (Made in the USA) to adhere the pennies to the floor. However, I'd recommend using good old fashioned Elmer's Glue (also Made in the USA). This glue adheres to both plastic and metal, so it seemed like the perfect choice, but we ran into some difficulties once we started to lay the pre-made penny tiles.
Can I use polyurethane to fill the holes between pennies?
Therefore, trying to fill the holes between the pennies with polyurethane is not a great solution. The poly may not dry between the pennies and that wouldn’t be a good thing. If you seal your penny floor with epoxy, the epoxy will harden between the pennies in the same way a grout would. In this case it’s not necessary to grout.
What epoxy is best for penny floor?
We recommend Wessex Permakote for this. It's a solvent-free, ultra-tough, two-part epoxy clear coating that pours like liquid glass and will give a stunning finish to your penny floor. It's resistant to water, alcohol, many acids and solvents.
Do you need to grout a penny floor?
If you seal your penny floor with epoxy, the epoxy will harden between the pennies in the same way a grout would. In this case it's not necessary to grout. But, grouting is also an option if you like the look of it — the grout will not affect the epoxy.
How well do penny floors hold up?
By the time you've glued down and grouted your pennies you've already got a tough durable floor that will stand up well to high traffic. If you then seal the floor with either epoxy resin or polyurethane floor sealant the you've got a pretty much indestructible floor!
How do you epoxy a penny table?
0:592:35Epoxy Penny Table Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing clean mixing containers measure equal parts of resin and hardener using a one to one ratio byMoreUsing clean mixing containers measure equal parts of resin and hardener using a one to one ratio by volume mix thoroughly with a paint stick being sure to scrape the sides.
How do you seal penny tiles?
0:151:36Quick & Easy Tips On How To Seal Grout - The Tile Shop - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you're sealing a grout joint just pour the sealer into a bowl or small cup use a poly brush toMoreIf you're sealing a grout joint just pour the sealer into a bowl or small cup use a poly brush to brush onto the grout try to get it off the tile.
Is it legal to make a penny floor?
On the one hand, you're at best taking U.S. legal tender out of circulation and at worst defacing it, which is a violation of federal law, but it's not like you're boiling down the pennies for use as scrap metal or using them for some other fraudulent activity.
Are penny tile floors hard to keep clean?
Penny tiles might be tiny pieces of perfection installed on the backsplash, entire walls, or flooring, but they are a tough job to maintain. Because the pieces are small, the grout around them collects debris and dirt over the years, and it can be hard to clean them out.
Is Penny tile expensive?
Cost for penny tile This kind of bathroom tile can range from $2 per square foot for porcelain to $10 or more for colorful mosaics.
How thick is a penny floor?
However, they're making a big comeback in the contemporary tile world. Once a classic, always a classic. The standard size of penny round tiles is ¾” in diameter (just like…
Can you use table top epoxy on floors?
Yes, you can use the Pro Marine Supplies Table Top Epoxy for flooring! For the same instructions that you would for coating a bar top. You will even be able to embed objects or add in pigments if you prefer.
What years of pennies are worth money?
Watch for low mintage years like 1955-S, 1939-D, 1933-D, and 1931-S. Depending on condition, rarer pennies are worth more. Look for all-copper pennies. Old pennies made before 1982 are 95% copper, which gives them an inherent metal value.
How do you make a clear epoxy table?
Step 1 Calculate how much mixed epoxy you'll need. ... Step 2 Set up your table top. ... Step 3 Clean and sand the surface. ... Step 4 (Optional) Attach item to table top. ... Step 5 Measure and mix resin & hardener. ... Step 6 Apply a thin seal coat of mixed epoxy. ... Step 7 Sand the dried seal coat. ... Step 8 Tape the edges to form a dam.More items...•
How hard is it to grout penny tile?
Grouting penny tile is extremely time-consuming. Think about it, each 12×12” sheet of penny tile has 240 individual tiles, and you have to make sure each of the joints between those 240 tiles are properly filled with grout. Say you're installing the penny tile on the floor of a 30-square-foot powder room…
Do you need spacers for penny tile?
Make sure to use a spacer between the penny tile and your countertop. That will help keep a straight line. 3. Squish and step back- when you put two sheets together, you will want to make sure that there is no visible seem.
How do you keep a penny tile floor clean?
Cleaning penny tile flooring should not be too tough if you are cleaning it regularly. This means using floor cleaners to mop on the floor at least once a week. Also, you can incorporate cleaning penny backsplash and floor with a textured cloth into your weekly cleaning routine to help keep the mold and mildew away.
How do you clean grout on penny tiles?
For floors, including penny tile shower floors, use a steam mop. (I use this one.) Direct the steam at the grout line and slowly move it back and forth for several seconds. Work in small sections, wiping away dirty residue before you move to the next section.
What kind of sealer do I use for hardwood floors?
The sealer I used was a polyurethane for hardwood flooring. It makes it as slippery like a hardwood floor — no more, no less.
What glue holds pennies down?
There are a few things that come into play with holding the pennies down. the Weldbond glue that adheres the pennies to the mesh. the thinset mortar the holds the pennies and the mesh to your cement board. the grout between the pennies.
Can I put a penny floor in my bathroom or shower?
I really would not recommend putting pennies in an area that’s going to get soaked all the time, like outdoors or in a bathroom or wet room… they’re not really a flooring material. Pennies can also get a little slippery when wet.
Is it legal to make a floor or other project from pennies?
It’s absolutely legal to use pennies as a building material, or indeed for any other purpose for which you could lawfully use a plain disc of copper-clad zinc (other than to melt them down to recover the metal therein).
What does a Penny Floor look like after 6 years of wear and tear?
Here’s a video I made of my floor in January 2018 — nearly 6 years after its been installed.
What is a penny floor template?
The penny floor template was designed for United States pennies.
Can you use unsanded grout on pennies?
Michael, I would recommend unsanded grout as it will be less likely to scratch the pennies. In addition, unsanded grout works better in joints that are less than 1/8″ wide so you won’t have any issues if the spacing of your pennies are close together.
How to glue pennies?
Gluing the pennies is VERY time consuming. I recommend using good old fashioned Elmer's Glue (Made in the USA) to glue the pennies. Use the Elmer's Glue and place each penny on the floor. The trick is not to use too much glue. Elmer's claims to dry clear, but it is a bit cloudy still once it dries. You can see EVERYTHING once the epoxy is laid, so don't use too much glue because you'll see the excess.
How to get air bubbles out of epoxy?
Use new buckets and stir sticks with each gallon you mix. Keep your eye on the epoxy for air bubbles when you pour. Apply heat with the blow torch or blow dryer to remove bubbles. You have up to 20 minutes to remove them and they will keep appearing for the full 20 minutes.
How long does it take to remove air bubbles from epoxy?
You have up to 20 minutes after you pour to apply heat to remove/pull up the air bubbles. Use a blow torch or very hot blow dryer to remove air bubbles. Keep your eye on the epoxy for the full 20 minutes because bubbles will keep appearing. Mark your space so you know what area to pour each gallon.
How hot does epoxy need to be?
Epoxy is very sensitive to temperature. The room must be at 75 degrees or more . My dad is super clever, so we used a space heater and a sheet hung over the doorway to trap in the heat. Otherwise, we would have been sweating and running up the electric bill for 3+ days. We also placed the epoxy in the room with the heater overnight so it was warm when we were ready to start mixing it.
How long does epoxy take to dry?
Finally, all that is left is to wait for the epoxy to dry and cure. Be patient! This should take at least 72 hours. I decided to do this three days before New Years and I was hosting a NYE party so I only had about 60 hours of drying time before I moved the oven and refrigerator back into the kitchen and it was fine. It survived high heels and about 25 people, but it was a risky move. I'd suggest giving it the proper time to dry and cure.
How many pennies per square foot?
If you lay the pennies very close and tight together is will be about 278 pennies per square foot. My 38 square foot kitchen took 10, 564 pennies!
How hot should a room be for epoxy?
Epoxy Tip #1: The room should be at least 75 degrees. We used a space heater to keep the room warm and hung a sheet over the door to trap the heat in. We also left the epoxy in the room over night so it was warm when se used it the next day.
How long does it take to glue pennies to the floor?
Here comes the time-consuming part! With the surface clean, you need to glue your pennies to the floor. We recommend using WEST SYSTEM G/5 Five-Minute Adhesive for this – it’s easy to mix, is ideal for spot applications and cures completely in 3-5 minutes.
What to do before you do any real work on your floor?
Before you do any real work on your floor, we recommend reading through everything below and doing a trial run on a test surface with a few pennies and some epoxy. Practice will make perfect!
Can you use Permakote on penny floors?
Now the hard work is done, you get the gratifying job of pouring epoxy all over your floor! We recommend Wessex Permakote for this. It’s a solvent-free, ultra-tough, two-part epoxy clear coating that pours like liquid glass and will give a stunning finish to your penny floor. It’s resistant to water, alcohol, many acids and solvents. What’s more, you don’t need to use a grout with it as Permakote will fill the gaps and level out for you.
Can you make a penny floor with epoxy?
The story of the IT worker who made his own penny floor went viral recently – and it’s easy to see why. With a load of copper pennies, some epoxy and just a little patience, you can create a stunning bespoke floor covering that really won’t cost you the earth. Here, we talk you through how easy it is to make an epoxy penny floor yourself.
Do you sand plywood before you stick it to the floor?
If you’ve used plywood, sand this first. Then, before you start sticking anything to the floor, you’ve got to make sure it’s scrupulously clean, so there’s no trace of dust, polish or wax.
Can you use entropy resins?
You can also use ENTROPY RESINS® for this project. Find out more from https://entropyresins.com
Can you pour epoxy over a floor?
You’re going to be pouring epoxy all over your floor later, so it’s vital you use an appropriate sealant to protect the edges of your surface – BEFORE you pour epoxy on. Epoxy will just trickle into any cracks… and once it’s there, it’s not going anywhere!
How much does a penny floor cost?
Cost: If plywood floors are the definition of a cheap diy flooring option then penny floors must be the definition of an expensive floor…okay not as expensive as some hardwood flooring, but lets face it…a penny floor will cost you nothing but money! As you will learn, a square foot of penny flooring will cost you about $2.78 …just for the pennies.
Where did penny floors come from?
We don’t know the origin of the first penny floor, but the The Standard Grill in New York and the Lincoln Restaurant in Washington, DC must take their fair share of responsible for inspiring most of the penny floor ideas we’ve seen.
Can you install penny floors anywhere?
Adaptability: As you will see from our examples below you can install penny floors anywhere. Most people choose a bathroom, toilet or kitchen/dining area, but you can install one wherever you like.
Can you hire a contractor to do penny floors?
One thing’s for sure, if you just have to have a penny floor then you won’t be hiring a professional flooring contractor to do it, an artist maybe, but not a contractor. So you need to learn now what’s involved in making a diy penny floor.
Can you put down a self leveling compound on a penny floor?
Our Irish Manor – Here’s another great bathroom penny floor. There’s some great info on how to put down a self-leveling compound to make sure you’re working with a flat subfloor. You will also see how this homeowner added a layer of latex primer to prepare the penny tile floor for the glass mortar he used to grout the design (note you still need to glue the pennies down!). What makes this penny floor really stand out is the superb wave design that was created using the natural patina of the copper coins.
What color planks would look good with penny combos?
Something like this, with the lighter gray planks, would look nice w/any of the penny combos.
Is Floor and Decor porcelain good?
btw, Floor and Decor really isn't known for quality. some of their stuff is ok, but if you're paying less than $4 a sq ft, then it isn't high quality italian porcelain.
Can you use subway tile on one wall?
then use larger subway tile or larger porcelain tiles for the other two walls. that way you still get a good quality, but since you are only doing one wall, it won't cost anymore. the subway tiles are cheap and will look good a long time.
