Why does my Maytag dryer have an AF error code?
A clogged vent or lint trap may cause an "AF" error code to appear in your Maytag dryer's display. Many homeowners count on their clothes dryers on a daily basis as part of their laundry routine. As a result, when a problem develops that prevents a dryer from operating properly, resolving it as quickly as possible is imperative.
What does the check vent light mean on a Maytag dryer?
Check vent light is on for your Maytag Dryer What is my Check Vent Light? The Check Vent Light is located on the console of the dryer (see diagrams below) and indicates that dryer airflow is restricted. Your dryer requires adequate air flow to ensure proper performance and dry times.
How do you clear the AF code on a whirlpool dryer?
The dryer is still operational when this error code is present, and the display may be cleared by pressing any button on the dryer's keypad so the dryer cycle may continue. To prevent the "AF" error code from appearing again, clean your dryer's lint screen after every load.
What does PF mean on a Maytag dryer?
The "PF" error code appears in a Maytag dryer's display when the appliance has experienced a power failure. If the dryer is only without power for a short period of time, it may be restarted by holding down the "Start-Pause" button. However, after a lengthy power failure, a new cycle must be started by pressing the "Power-Cancel" button.
See more
How do I fix the f1 code on my Maytag dryer?
The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.
What are the codes for Maytag dryer?
Error CodesAF or "Check Vent" AF or "Check Vent" - Dryer.Check Lint Screen. Check Lint Screen - Error Code - Dryer.F#E# F#E# - Error Code - Dryer. ... Other Error Codes. 0E - Error Code - Dryer. ... Purchased in 2020. "Check Vent" - Dryer. ... Starts with E. E1 - Error Code - Dryer. ... Starts with F. F01 - Error Code - Dryer.
What does good airflow light mean on Maytag dryer?
The Check Vent Light is located on the console of the dryer (see diagrams below) and indicates that dryer airflow is restricted. Your dryer requires adequate air flow to ensure proper performance and dry times.
How do you check a Maytag dryer vent?
Run the dryer for 5-10 minutes. Hold your hand under the outside exhaust hood to check air movement. If the air movement is less than a hair dryer on high speed, clean the lint from the entire length of the system and the exhaust hood. Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.
How do I read a Maytag error code?
0:045:38How to Run Diagnostics and Read Error Codes on a Maytag WasherYouTubeStart of suggested clipEnd of suggested clipAnd then when it engages the lights flash. And if we do one more tick to the right. The done lightMoreAnd then when it engages the lights flash. And if we do one more tick to the right. The done light lights. Now if I were to push start now it would allow me to read any previous error codes.
How do I reset my Maytag dryer?
The Maytag dryer might display an error code if a problem has arisen with the dryer. Examples of error codes for Maytag dryers include "AF," "PF" or "F" with a number. To reset the dryer if an error code occurs, press "Power/Cancel" twice and then reselect a cycle and press "Start."
How do you clear the AF code on a dryer?
Try the following: Clean the lint screen. Check to see if the house vent from the dryer to the wall is crushed or kinked. Confirm that the house vent from the dryer to the wall is free of lint and debris. Confirm that the exterior vent exhaust hood is free of lint and debris.
Why does my dryer keep saying AF?
An AF (Restricted Air Flow) error code indicates that the lint screen or house vent is clogged; the vent may be crushed, kinked or have too many turns. The dryer will continue to run when the is error is present. Touch any key to clear the code from the display and return to the estimated time remaining.
How do I clean my Maytag dryer vent?
2:074:58How To Clean A Dryer Vent - Whirlpool, Maytag, Kenmore, GE ...YouTubeStart of suggested clipEnd of suggested clipOnce it's off you can stick your long handle flexible brush inside the vent hose. And pull out asMoreOnce it's off you can stick your long handle flexible brush inside the vent hose. And pull out as much lint as possible. Go back in with your vacuum to clean up any remaining. Lint.
How do I know if my dryer vent is clogged?
The Warning Signs and Dangers of Clogged Dryer VentsIt takes longer than usual to dry your clothes. ... You notice a burning smell. ... Your clothes are hot to the touch at the end of a load. ... You can see lint or debris in the dryer hose or around the outside dryer flap. ... You haven't cleaned out your vents in over a year.
Can I clean dryer vent myself?
Cleaning a dryer duct isn't difficult. Remove lint from the duct by hand and then vacuum the inside of the duct. Use hose extensions, if available, to vacuum out as much of the duct as you can. Go outside the house and remove the exterior vent cover.
How do you clean the inside of a dryer vent?
How to Clean Out a Dryer Vent in 7 Simple StepsGather Your Cleaning Supplies. ... Pull the Dryer Out From the Wall, Unplug It, and Disconnect the Duct. ... Vacuum the Inside of the Vent. ... Connect the Flexible Rods in Your Dryer Duct Cleaning Kit to Your Power Drill. ... Turn On the Drill and Let the Brush Work Its Magic.More items...•
What does E3 and F6 mean on Maytag dryer?
The F6 E3 alert indicates there is issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait five minutes, then plug back in.
What does F4 E1 mean on Maytag dryer?
Control displaying F4 E1: There may be a problem with the Heater or Heater Relays. Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Start a time dry cycle. Monitor the dryer for one (1) minute to ensure the error code does not display again.
What does f3 mean on a Maytag dryer?
Moisture Sensor Issue The F3E2 error code occurs when five consecutive loads are dried without registering moisture sensor data. Pressing the 'Power' button will clear the error code and allow you to restart the machine. If the problem persists, call for service.
What do you do when your Maytag dryer won't start?
FIXING A DRYER THAT WON'T START: A GUIDESTEP 1: CHECK THE “START” BUTTON. ... STEP 2: MAKE SURE THE POWER IS ON. ... STEP 3: INSPECT THE DRYER DOOR. ... STEP 4: SELECT THE CORRECT CYCLE OPTIONS. ... STEP 5: CHECK “CONTROLS LOCKED” INDICATORS.
Is JustAnswer responsible for posts?
Disclaimer: Information in questions answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.
Where is the dryer vent located?
It is located on the blower housing behind the front panel on your dryer.
Where is the thermistor located on a dryer?
It is located on the blower housing behind the front panel on your dryer. You will have to remove the front panel to access and remove the thermistor. I couldn't find a video that shows your exact dryer, but this video will show you what you will be looking for and the location.
Why does my Maytag dryer have an AF code?
A clogged vent or lint trap may cause an "AF" error code to appear in your Maytag dryer's display. Many homeowners count on their clothes dryers on a daily basis as part of their laundry routine. As a result, when a problem develops that prevents a dryer from operating properly, resolving it as quickly as possible is imperative.
What to do if dryer says "AF"?
You may also want to check the dryer's exterior vent exhaust hood for debris. If the "AF" error code continues to appear, your dryer's vent may need to be professionally cleaned. Advertisement.
What does PF mean on Maytag dryer?
The "PF" error code appears in a Maytag dryer's display when the appliance has experienced a power failure. If the dryer is only without power for a short period of time, it may be restarted by holding down the "Start-Pause" button. However, after a lengthy power failure, a new cycle must be started by pressing the "Power-Cancel" button.
How to clear L2 code on dryer?
The code may be cleared by pressing any button on the dryer's keypad, and the dryer will continue its cycle. However, if the "L2" error code appears, you should check your home's circuit breaker or fuse box to determine if the breaker needs to be reset or fuses require replacing.
Where is Jennifer Blair?
Jennifer Blair. Based in New York City , Jennifer Blair has been covering all things home and garden since 2001. Her writing has appeared on BobVila.com, World Lifestyle, and House Logic. Blair holds a Bachelor of Arts in Writing Seminars from the Johns Hopkins University in Baltimore, Maryland.
When did we buy the Maytag Bravo XL?
We purchased our Maytag Bravo XL in 2012. Over the past year and a half we
Does a Maytag dryer wrinkle?
Maytag washer leaves clothes more wrinkled after a wash than they were in before being cleaned. And these are not full laundry loads. Then using the Maytag dryer is a joke. Need to run double times or extended times on most of the settings to get them completely dry. When it comes to the wrinkle free setting... what a joke. Clothes might be close to dry but wrinkled. Have always had Maytag products since forever. Tried Samsung for the last set-----washer lasted 6 years and then needed a full overhaul. Cheaper to buy a new set. Went back to Maytag. MISTAKE. Samsung did a lot better job of washing and drying. Now stuck with Maytag until... when? Retired and dont have the funds to get new replacements. Just my opinion though.
What is my Check Vent Light?
The Check Vent Light is located on the console of the dryer (see diagrams below) and indicates that dryer airflow is restricted. Your dryer requires adequate air flow to ensure proper performance and dry times.
How to prevent dryer vent from crushing?
If the venting it crushed, replace it with rigid or flexible metal venting. Allow a minimum of 4" between the dryer and the wall when reinstalling the unit to prevent further crushing. Check that the vent hood on the exterior of the house is not clogged or being blocked by ...
Can you clean a vent hood?
Check that the vent hood on the exterior of the house is not clogged or being blocked by landscaping. Clean internal house venting ; this may require a Vent Cleaning service person depending on venting installation. This cleaning is not covered by warranty and will not be performed by an Appliance Service Technician.
