Why does my Whirlpool washer keep saying OL?
2 Answers. First, OL stands for “Overload”, so in other words, the washer thinks the tub is too hard to move because it's overloaded and the motor is struggling or the unit is way out of balance causing the washer to struggle. The most common problem is a nut below the inner tub that needs to “float”.
How do I reset my Cabrio Whirlpool washing machine?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
How do I fix my Whirlpool Cabrio code?
0:112:30OL error code on Whirlpool Cabrio washer after bearing changeYouTubeStart of suggested clipEnd of suggested clipIt basically lets it see or I guess it tells the processor. That it's not overloaded. So the tubMoreIt basically lets it see or I guess it tells the processor. That it's not overloaded. So the tub sort of floats inside of of there the wash tub. Inside of the main tub.
What does Ld mean on Whirlpool Cabrio?
The LD error code is short for "long draining." That means it's taking too long for water to vacate the washer if it drains at all, and the machine is shutting off despite water being in it.
Does a Whirlpool Cabrio have a reset button?
Try the Cabrio Reset Procedure Touch any button that you see on your display pad. This will clear the error code. Or you can press PAUSE/CANCEL. Choose a cycle and press START.
How do I reset my top load Whirlpool washer?
Follow these steps to reset your Whirlpool washer:Turn the washing machine off using the control panel.Unplug the washing machine.Wait three minutes.Plug the washer back in, and wait thirty seconds before turning the washer on.
How do you put a Whirlpool Cabrio washer in diagnostic mode?
3:148:04How to Put #Whirlpool #Cabrio #Washer into Diagnostic Test ModeYouTubeStart of suggested clipEnd of suggested clipSo i just press one two three. And and release one two three. And then until i get to the test modeMoreSo i just press one two three. And and release one two three. And then until i get to the test mode so you have to be very patient to be able to get on the test mode.
How do I reset my top load washer?
Motor Reset Procedure:Unplug the washer for 1 minute from the electrical outlet.Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. ... The motor has now been reset and is ready for you to start a cycle.
How long does a Whirlpool Cabrio washer last?
about 14 yearsHow long will it last? Top loaders typically have a longer life than front load washing machines. This model should last about 14 years.
Why is my Whirlpool Cabrio washer not draining?
If your washer still doesn't drain, remove the hose that runs from the pump to the drain. Make sure this hose is free from debris and blockages. If your pump is getting power, and no clogs are found it's best to replace the drain pump motor. You can also use a multimeter to check for continuity inside the drain pump.
What does Ld mean on a washer machine?
"LD" in the washer display indicates an issue with draining. If this display occurs and/or the washer is not draining: Verify the drain pump filter (where applicable) is clear (the filter is accessible through the door at the bottom of the unit).
What does error code Ld mean on Maytag washer?
Long Drainmamajtown, Ld code is for Long Drain: this could indicate that the washing machine is taking longer than 5 minutes to drain out enough water to reset the water pressure switch.
What does OL mean on Whirlpool Cabrio washer?
Whirlpool Cabrio Washer Error OL. The Cabrio Washer OL error code stands for overloaded which means the control has recognized that the load in the tub is to much for the machine to handle or there is friction on the drive system not allowing the basket to disengage.
Why is my washer thinking the tub is too hard to move?
First, OL stands for “Overload”, so in other words, the washer thinks the tub is too hard to move because it's overloaded and the motor is struggling or the unit is way out of balance causing the washer to struggle. The most common problem is a nut below the inner tub that needs to “float”.
What does F then 41 mean?
F then 41 flashes when the motor rotor position sensor (RPS) thermistor is detected to be open or shorted out.
Why is my washing machine basket not engaging?
This may signify excessive detergent usage, the basket cannot engage during drain step, or mechanical friction on drive mechanism not allowing the basket to engage.
What does UL mean on a washer?
uL is displayed when the machine/motor control detects an off-balance load and remains on while the washer runs a mini-cycle to rebalance the load.
Why does F then 51 flash?
F then 51 flashes when there is a motor rotor position sensor (RPS) failure.
How to clear the display on a washing machine?
Open the lid to clear the display, remove excess laundry, then restart the cycle.
What happens if mini cycle fails?
If the mini-cycle is unsuccessful, uL will flash until the lid is opened, allowing the customer to view and redistribute the load.
What is preventing the lock bolt from extending?
Lint and detergent residue is preventing the lock bolt from extending.
What to do when Whirlpool Cabrio is whining?
The first step is to find a repair manual or diagram of the internal workings of the washer on the Whirlpool site.
What does it mean when a Cabrio washer doesn't spin?
If your washer does not spin or agitates, it means your drive belt is broken or loose on your Cabrio washer’s pulleys. Replacing this belt will restore functionality to your machine.
Why does my washer lid not fill?
When your washer lid unlocks, it could throw off the calibration, which may cause your machine to overfill or not fill enough. These problems can throw off the wash time and cycle, leaving you with a load of laundry that’s not as clean as you expected, or worse, another load of laundry to do after the first one.
Why does my washing machine make a rumbling noise?
There are a number of reasons why this might occur. The washer can emit a rumbling sound while agitating while draining or spinning. Causes might include misalignment of the impeller, imbalance of load, or build-up of lint in the drain pump.
What is the purpose of a spin cycle in a washing machine?
The main function of the cycle is to take the laundry from being soapy and wet, and throw it around in a circle to get it clean. The Cabrio has an excellent spin cycle that can take even the most soaked items and get them clean and dry in no time.
Why does my Cabrio washer clog?
When the machine is draining the water from the tank, if there are any socks or other small particles that have been sucked into the pump, they can clog the pump. To ensure smooth functioning of the Cabrio washer, please take a few moments to remove and clean any obstructions that have been sucked into the pump.
How to take a break on a Cabrio washer?
When it’s time for your Cabrio washer to take a break, put the machine in standby mode. You can do this by plugging it in with all indicators off, or by turning on only the clothes clean or done indicator. Once the machine is ready to rest, choose any button except POWER, START, or STOP. Then follow the step-by-step instructions below.
