What does the SLP or SL message on the display mean?
Warning! If the SLP or SL Message is Alternating with the Water Temperature on the Display, the Spa is Operating in the Sleep Heating Mode. If the SLP or SL Message is ON Solid (Not Flashing) on the Display, the Spa is Operating in the Sleep Heating Mode, but there is No current water temperature because the Spa is between Filter Cycles.
What is a hot tub’s sleep mode?
Most hot tub owners are familiar with how to turn their hot tubs on and off. That’s fairly easy to explain. When the hot tub is placed into the ON position the water is heated to a temperature optimal for relaxation, and in the OFF position the hot tub’s heater, pump, and jets essentially have no power. So, What is a Hot Tub’s Sleep Mode?
What does--PR mean on my hot tub?
Pr : This message is displayed when your hot tub is first powered on. The Priming cycle will last from 4-7 min. There is no action required during this time, just wait to hit any buttons till this message goes away.--F or --C : Temperature unknown. There is no action required. After 2-4 min of the pump running the temp will be displayed.--
What does “watchdog” mean on a hot tub?
“Watchdog” (spa is deactivated), likely a bad temp or hi-limit sensor or water temp has reached 118ºF Unknown water temperature. (Displays when first powered up after refill) Cool condition. Water temp 20ºF below set temp. Low speed pump & heater activate
When to use sleep mode on hot tub?
Why do hot tubs go to sleep?
How long does it take for a hot tub to heat up?
What happens when you put a hot tub on?
How many times can you hit the temperature down button on a hot tub?
When does a hot tub heater kick on?
Is it better to sleep in a hot tub or turn it on and off?
See 4 more
About this website
What code is SLP on a hot tub?
Sleep Heating ModeIf the SLP or SL Message is ON Solid (Not Flashing) on the Display, the Spa is Operating in the Sleep Heating Mode, but there is No current water temperature because the Spa is between Filter Cycles. Ecn or Ec is Alternating with Temp: The Spa is Operating in the "Economy" (Ecn or Ec) Heating Mode.
What does SLP mean on a bullfrog hot tub?
sleep modeWhile your hot tub is in sleep mode (or 'SL' & SLP mode on some models), the jets will operate occasionally to filter the water. In sleep mode, your hot tub's heater will usually only kick on once the temperature dips below 20 degrees of the set temperature.
What are the codes on a hot tub?
Balboapd = Power supply, unit running on battery backup.OH = Sensors reading 112-118° F.OHH = Overheat. Spa has shut down. ... OHS = Overheat. ... Flo = Improper flow or pressure switch malfunction.Cool = Water temp 20° below set point.ICE = Potential freeze condition has been detected.Sn1 = Hi-limit sensor malfunction.More items...
What mode should my hot tub be in?
Economy is a good setting for those who use the hot tub daily. The drop in temperature fluctuates during the year from minor or no temperature falls in the summer, to larger drops in the coldest part of winter.
How do you fix the error code on a hot tub?
0:112:26Fix a Flow Sensor Error on Your Hot Tub and Fix Your Spa Not HeatingYouTubeStart of suggested clipEnd of suggested clipTurn your spa off and put the filter in finally turn your spa back on again and run your jets for aMoreTurn your spa off and put the filter in finally turn your spa back on again and run your jets for a few minutes. This should remove any air that's in your lines.
What does SL mean on hot tub display?
SLEEP MODE (Sl): In this mode, your hot tub will heat the water up to the set temperature but only during the filtering cycles. You have the option to set each filter cycle to run anywhere from 30 minutes to 6 hours, with each cycle in increments of 30 mins.
What does PR mean on hot tub?
priming modePr or Pr--, also known as "priming mode", runs after turning the hot tub on. If the priming mode does not clear after approximately 7-minutes you may need to prime the pumps (they may have an airlock). Pr may be followed by dr, dY, HH, OH, HL or LF (these errors indicate low or no water flow).
How do I get my hot tub out of economy mode?
0:191:14Evolution Spa Hot Tub Economy Mode - How to Cycle ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you do it one more time. It. Goes back to standard mode and that's what the normal runningMoreSo if you do it one more time. It. Goes back to standard mode and that's what the normal running mode that. Will keep the heater on when the temperature is going down on your spa.
How do I reset my hot tub jacuzzi?
1:112:01How to RESET your HOT TUB - YouTubeYouTubeStart of suggested clipEnd of suggested clipGo over to your breaker panel. And flip your breaker or breakers. Down there are some hot tubs thatMoreGo over to your breaker panel. And flip your breaker or breakers. Down there are some hot tubs that have two breakers. And some hot tubs that have one breaker.
What temperature should I keep my hot tub when not in use?
So, what is the ideal hot tub temperature when not in use? A good rule of thumb to follow is always keeping your hot tub's temperature 5 degrees below what it usually is.
What are the different hot tub modes?
"Economy" mode will allow your hot tub to heat only between the hours of 5 PM and 7 AM, "Day" mode will allow the water to heat only between the hours of 7.00 AM and 5.00 PM. These hours are not programmable. "Auto" allows the heater to heat, at all times, in order to maintain your preset temperature.
Should my hot tub be on standard mode?
Standard (Std or St) This is the most common operating mode, and is sometimes the only operating mode, depending on the system configuration. This mode allows you to heat your spa at any time, as long as the water hasn't reached the desired temperature.
How do I reset my Bullfrog hot tub?
You can often reset the spa unit by pressing the “jets” button. Means that the temperature of the water is unknown. When the pump has been running for a total of 1 minute, the temperature is displayed.
How often should I shock my Bullfrog spa?
once a weekExperts recommend shocking your hot tub at least once a week to keep your water clean and clear.
What is filter cycle for Bullfrog spa?
Filter cycle start times: 8:00 AM, duration 1.5 hours and 8:00 PM, duration 1.5 hours.
How do I get my hot tub out of economy mode?
0:191:14Evolution Spa Hot Tub Economy Mode - How to Cycle ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you do it one more time. It. Goes back to standard mode and that's what the normal runningMoreSo if you do it one more time. It. Goes back to standard mode and that's what the normal running mode that. Will keep the heater on when the temperature is going down on your spa.
How to get a hot tub to exit SL sleep mode? - JustAnswer
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts.
How to Get the Heat on a Master Spa From Economy to Standard
Standard is one of the three programmable modes on a Master Spa. Standard mode is designed to keep the Master Spa hot at all times by maintaining the last set temperature. Economy mode is designed to save energy, heating the spa to the last set temperature only when a filter cycle is running.
How to switch hot tub mode?
Keypads without a "Mode" button. Press "Temp", then "Light" to switch to the next mode. Repeat the process until you reach the mode that you're looking for.
What are the operating modes on a Balboa hot tub?
Most Balboa hot tub control systems have three operating modes: Standard , Economy and Sleep. These modes affect the times at which the hot tub will heat, and therefore affect the overall power consumption. This is the most commonly-used mode, and in some cases it may be the only one available, depending on the configuration of your hot tub.
Does a hot tub pump run all the time?
Note that this mode still has an effect if you have a 24-hour circulation pump. Even though the pump runs all the time, there will still be hidden "filtration cycles" programmed in your hot tub control system.
Flow errors
Flow errors are one of the most common error codes triggered when the hot tub’s sensors detect a lack of water flow through the heater element. Specific examples of flow error causes include:
Low water errors
Low water error codes tell you there’s a lack of water in the hot tub pump. Your hot tub water line should be sitting at the waterline indicator typically located somewhere on the shell or by the filtration skimmer.
High limit errors
High limit error codes are typically caused when the hot tub water gets too hot. To diagnose, get your thermometer out and check the temperature of your tub. If it’s above 110 degrees Fahrenheit, you might have a problem with your heater or spa pack. If it’s normal, you might be dealing with a faulty temperature sensor.
Cold water and frozen water errors
Cold water error codes happen when the hot tub detects much colder water than the set temperature. Get your thermometer out and test out your water. If it’s colder than the set temperature by 10 degrees or more, then you likely have a problem with your heater.
Panel errors
Panel error codes come up when there are signs or symptoms or a broken electronic component. This could be anything ranging from a broken sensor to a blown fuse. Your best bet is to call a professional to help you diagnose and repair the issue.
Circulation pump errors
Circulation pump error codes occur when there’s a problem with the hot tub’s circulation pump. If you also have noise coming from your pump, that’s a good indication of a problem. Common causes include air trapped in the lines, scale deposits, clogged impellers, or bad bearings.
What does "slp" mean on a water heater?
SLEEP (SLP) mode means it will only heat when the water reaches freeze temp.
What does the flashing light on a water heater mean?
The display will flash between econ and preset temperature whenever the water temperature is less then the user set temperature.
Is a patinum spa always ready?
The Patinum spa is always ready and clean and not complicated as some spas are with filter cycles, clean cycles ect. What is nice about your spa control is you can order a indoor wireless control and a floating remote that both are simple plug and play devices. I plan on ordering the remote wireless pad so I can see and change the settings from inside my house.
What temperature should my spa water be?
One of the sensors has detected that the spa water is 110°F. Remove spa cover and let the water cool down. At 107°F the spa should reset. If spa doesn’t reset there is an issue with sensors or PC board.
How many times a day does a hot tub filter?
While in Sleep mode your hot tub will filter 2 times a day for 2 hours a piece. Your hot tub does NOT heat during this time in this mode.
What does "hfl, lf, dr" mean?
For the error messages of HFL, LF, Dr, or DRY. This means that there is a flow issue through your heater. Try and clean your filters. While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump. Run a hot tub temporarily with filters out of the hot tub and see if the problem continues. If error message goes away you have dirty filters. If the problem continues make sure circulation pump is moving water. Order replacement filters.
When to use sleep mode on hot tub?
When to Use Sleep Mode. Sleep mode is useful when you don’t plan on using your hot tub for several days, such as when you go on vacation. Some hot tub models can even be pre-programmed to enter sleep mode during certain hours of the day. This is a great way to conserve energy while keeping your hot tub nearly ready to use.
Why do hot tubs go to sleep?
To summarize, your hot tub’s sleep mode is a useful way to conserve energy while also keeping your hot tub at a temperature that will be easy to heat up once the hot tub leaves sleep mode and enters into a standard mode of operation . Be sure to stay up on hot tub maintenance, and if you ever have an issue in getting your hot tub out of sleep mode, simply contact your friends at Master Spa Parts. We’re always here to help!
How long does it take for a hot tub to heat up?
After all, depending on the temperature outside, it can take upwards of 24-48 hours to heat up a hot tub — that’s a long time to wait for an impulse session in the spa. So, instead of always keeping a hot tub’s water always ready for use (or completely cold), sleep mode will keep your hot tub’s water at a temperature that can be easily raised in ...
What happens when you put a hot tub on?
When the hot tub is placed into the ON position the water is heated to a temperature optimal for relaxation , and in the OFF position the hot tub’s heater, pump, and jets essentially have no power.
How many times can you hit the temperature down button on a hot tub?
Now, you could simply hit the temperature down button a couple dozen times when you won’t be using your hot tub for a spell, but then you also have to do the same button-tapping process to raise the temperature. Sleep mode saves you from having to do this repetitive task.
When does a hot tub heater kick on?
In sleep mode, your hot tub’s heater will usually only kick on once the temperature dips below 20 degrees of the set temperature. Your hot tub is going to run its normal filtration (whatever you have the spa set at) time and during that time is when your heater will run.
Is it better to sleep in a hot tub or turn it on and off?
While it may seem counterintuitive, according to the laws of thermodynamics, it takes less energy to keep your hot tub at a steady, warm temperature than turning the unit on and off regularly. Plus, your hot tub is likely insulated and will therefore retain a good amount of heat. So, if you are looking to save some money while keeping your hot tub primed for use, the sleep mode should be a beneficial feature for you.
