What is a BoWrench used for?
BoWrench ® Easily and quickly straightens twisted and warped boards. The BoWrench ® gives you a fast, one-person way to straighten decking boards. This is great, because decking material… whether redwood, cedar, or pressure treated pine… is often warped, especially in 12 to 16 foot lengths.
How do you use a deck wrench?
1:022:04DeckWise Hardwood Wrench - Deck Board Straightener - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply place the wrench on joist or furring. And position the joist pins. And cam against the boardMoreSimply place the wrench on joist or furring. And position the joist pins. And cam against the board tightly rotate.
What can I use as a spacer for decking?
Reuse Plastic Lids. Sixteen-penny nails work great as spacers when you're installing deck boards, but they often fall through the cracks. Keep the nails in place by pounding them through plastic jar covers. They're easier to move and will stay up on the deck instead of falling on the ground.
How do you take deck boards together?
2:316:33Five Ways To Cinch Deck Boards || Dr Decks - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then when you push down on the lever. It actually grabs here and then pushes the board in and itMoreAnd then when you push down on the lever. It actually grabs here and then pushes the board in and it does the same thing it keeps everything locked together nice and tight.
How do you tighten deck boards?
0:324:35Replace Deck Boards and How To Straighten Bent Wood Planks To ...YouTubeStart of suggested clipEnd of suggested clipI start at one end of the board. And then go to the other end to bend the board in position beforeMoreI start at one end of the board. And then go to the other end to bend the board in position before securing it with the screws. Then i could install screws over the rest of the joist. Locations.
How can I make my deck boards straight?
0:003:23“installing” decking boards STRAIGHT and even - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn order to make sure that the wood doesn't split when we put in our two and a half inch deckingMoreIn order to make sure that the wood doesn't split when we put in our two and a half inch decking screws i'm going to pre-drill it with an 8-inch. Bit. Using a clamp i'm going to readjust.
Do I need spacers for decking?
Proper deck board spacing should have a 1/8-inch gap after the decking has dried out. If you install your decking using wet boards, pressure-treated decking that has not yet dried out, then you should install them with no gap as a gap will be created as they dry and shrink.
Why are spacers used in decking?
The protective decking spacer strip is inserted between timber decking and the substructure when face fixing the deck boards. It is designed to help prevent moisture from becoming trapped between timber components by increasing air circulation.
What gap should be between decking boards?
¼” to 3/8” inchThe amount of space between deck boards should be anywhere from ¼” to 3/8” inch. You want plenty of space for water to flow between the boards and to allow small debris to fall to the ground. Deck board spacing greater than 3/8” of an inch can become problematic.
Can I flip old deck boards?
1:243:06How To Flip A Deck Board (Refinishing A Deck) - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt over and I can show you that by flipping the deck board over I can get a much better look and aMoreIt over and I can show you that by flipping the deck board over I can get a much better look and a much better surface on the deck board without actually replacing. Anything.
Why are my deck boards cupping?
When the external forces become too powerful for the wood, the wood will move, typically cupping upwards at the outside edges. Too much sun on the top, combined with too much moisture below.
How do I keep my deck boards from warping?
Generally, six screws placed the length of your board will keep the board flat and secure. Use two screws at either end of the board and two more towards the outside of the board at every joist. This will keep the boards in place, giving them no room to move or warp.
Product Overview
The Universal Bowrench BW90 is a simple to use tool that is great for both professional deck builders and also for those who want to do it themselves. You simply fit the adjusted gripper onto a joist, swing the lever and release. This tool is great for warped wood especially at longer length.
Info & Guides
You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.
