What is a door tongue? The beveled "tongue" spring mechanism that extends from the edge of the door into the door jamb to hold the door shut when closed. Click to see full answer. People also ask, what are parts of a door lock called? The lock body, or lock cylinder, is the core of a door lock.
What is a tongue on a door lock?
The beveled "tongue" spring mechanism that extends from the edge of the door into the door jamb to hold the door shut when closed. Click to see full answer. In this manner, what are parts of a door lock called? The lock body, or lock cylinder, is the core of a door lock.
Why choose tongue and groove doors?
This style of door is attractive and imparts a country feel to the surroundings reminiscent of farms and ranches. With the right bracing, a door made from tongue and groove wood is solid and will hold up over the years.
How do you make a 36 inch tongue and groove door?
Start by building a door for a 36-inch opening with typical 4-by-96-inch tongue and groove wood. Lay nine pieces of tongue and groove wood face down parallel to each other on a flat surface. Match the tongue on one board with the groove on the other board.
What are the parts of a door called?
This door has a top, bottom, and a mid-rail. A stile is the narrow vertical segment located on either side of a door panel. One is called the lock stile and the other a hinge stile. A mullion resembles a stile.
What are the parts of a door handle called?
Handle.Rose.Lock Cylinder.Spindle.Latch Assembly.Deadlock Latch.Strike Plate.
What do you call the tongue of a lock?
Latch – This is the part of the lock that actually protrudes from the door into the door frame/jamb, providing the physical means for securing the door. In some types of locks, this is often referred to as the 'bolt' or 'tongue'.
What is the hole in the door jam called?
Bore hole. A bore hole is drilled into a door to accommodate a lockset.
What do you call the part of the door the lock goes into?
CylinderCylinder (Lock Body) The cylinder, or lock body, is the part of the door lock where you insert the key. When it's locked, the cylinder engages a series of spring-loaded pins which keep the cylinder from turning.
What is a door striker?
When discussing door hardware, a "strike" or "door strike," refers to the metal plate or assembly that's installed into or onto a door frame to "catch" the latch or bolt to hold the door closed. You've seen thousands, maybe millions, of door strikes in your lifetime.
What is a Deadlatch on a door?
“Deadlocking plunger” (also called “deadlatch plunger” or “deadlock plunger”) is the name of a very important piece of a door lock assembly; it keeps a locked door from being opened with a small screwdriver or credit card.
What is the metal thing at the bottom of a door called?
A door jamb runs vertically along the side of the door. It helps provide support for the door panel and door frame. What is the piece at the bottom of the door called? The piece at the bottom of a door is called a sill. Door sills help prevent air and water from getting in your home.
What is the door catch called?
The latch is the mechanism that slides into the enge of the door and retracts or protrudes with the turn of the door knob. The latch keeps the door closed and when the knob is turned allows the door to open.
What do you call doors that open in the middle?
Dutch doors are essentially a single door that is split in the middle to allow the top half to open while the bottom half remains shut.
What are the metal things on doors called?
The strike plate is placed on the door jamb where the hole for the bolt of the door and the bolt meet. It is a small metal plate that is screwed to the door jamb.
What is Door Knob?
A door knob handle or a round knob door lock is a mechanism used to open up or shut a door. The standard door knob has a bolt or spindle running th...
What did people use before door knobs with locks were designed?
Before knobs and locks, as well as door handles were designed, people often simply made use of locks with tricks, if they might pay for to have a l...
What are the different types of door knobs?
Generally speaking, according to different structures and usage environments, door knobs can be divided into the following four types: Keyed door k...
ow does door knob work?
A door handle controls the door by the control of a lock, which attaches the gate with its frame. Every time you lower on a door deal with, you are...
What are the common surface finishes for door knobs?
The most popular door knob locks are polished brass, polished chrome, satin chrome, and satin nickel door knobs. Refined brass is just the base bra...
What is a twist pin door?
The main feature includes a twist , push pin, or turn button to open or lock the door from one side (inside or outside), but the other side no key device on the outside knob to open the door. It is often used in bathrooms and toilets.
How do door knobs work?
A conventional doorknob lockset contains a set of knobs, one on each side of the door, attached via the door by a pin and held together by placing screws. The spindle goes through the lock screw, which is inside the door perpendicular to the pin.
What happens when a door knob turns?
When either knob turns, it rotates the spindle, and the spindle retracts the latch and allows the door to open. In most cases, the spindle is spring-loaded so that the latch springs back into the closed position when the doorknob is released.
What is a doorknob lock made of?
The most popular doorknob locks are polished brass, polished chrome, satin chrome, and satin nickel doorknobs.
What is the faceplate on a door?
The faceplate is a flat steel plate on the edge of the door where the latch protrudes; it is secured to the door with screws and also holds the lock in place.
What is the bolt on a door knob?
The standard door knob has a bolt or spindle running through it that rests just above a cylindrical tube to which the spindle is attached. Turning the handle draws the cylindrical tube in the direction of the turn. The end of the cylinder is the “latch bolt” (even more just referred to as the “lock”), which extends right into space carved out ...
What are the components of a handle?
The essential components are the knob climbed, shank, pin, as well as knob-top. The knob-top is the upper and also majority that is understood by the hand. The shank is the predicting stem of a handle and has a hole or socket to receive the spindle.
Step 1: Cut Rails & Stiles to Length
I starting by cutting my pieces to length on the miter saw. I set up a stop block to first cut the 2 sides (which are also called stiles) and then did the same to cut the top and bottom pieces (which are referred to as rails).
Step 2: Cut Thin Grooves
The first step is to set the height of the blade, which will be the depth of the grooves. I cut a scrap piece of wood to exactly 3/8ths and used that as a gauge to set the height. I adjusted the blade height until the very tips were flush with the top and then locked that height in.
Step 3: Widen the Grooves
With that step complete, I have a thin groove in all 4 of my pieces, as well as my test piece. Next it’s time to widen the grove to the perfect size.
Step 4: Cut the Tongues (tenons)
With the grooves done, it’s time to move onto the tenons. Back to my test piece, I drew a line flush with the bottom of my groove. This will help me set my table saw so that the tongues are the exact same depth as the grooves.
Step 5: Cut the Center Panel
Next I need to cut the center panel to size, and in order to figure out how big I need to cut it, I assembled the frame and measured the inside of the frame. I then added 3/8 on each side to account for the grooves, then removed an eighth just to give me some wiggle room.
Step 6: Assembly
After doing a dry fit to make sure everything fit without issue, it’s time to glue it up. I didn’t glue the center panel to allow for any potential movement. I only applied glue to the tongues, spreading the glue all around and sliding the rails into place.
Step 7: Apply Finish
All that’s left is a little sanding and this door is a wrap! I’ll be using this door in my workshop for my miter station, so I’m leaving it unfinished, but you can paint, stain, oil or varnish the door however you like.
What is a door sill?
Sill. Sills are the bottom component of a door frame. They are the part of the door that gets sealed and fastened to the floor. Only exterior doors (those that lead to the outdoors or garages) have sills. Learn how to prep a floor for a door sill .
How many hinges does a door have?
This is the piece of hardware that allows the door to swing open and closed. Standard sized doors have three hinges, but larger doors will have four or more. The color or finish of the hinges typically matches the finish of the lockset.
What are door frames made of?
Residential door frames are most often made of wood but can also be made of aluminum, fiberglass, or a composite material. Door frames can be purchased primed (ready to paint) or ordered with a factory finish in a variety of colors.
Do all exterior doors have deadbolts?
Residential interior doors are not equipped with deadbolts, and not all exterior doors have them either. Deadbolts are considered an additional form of security and are most often set apart from the handle assembly, which means that a door with a deadbolt needs an additional bore hole.
What is pocket door?
A type of door installed on a sliding track that slides into and out of a hollowed space in a wall. Any standard door can be used as a pocket door. Pocket doors are used to free up space in a room by eliminating the necessity to maintain clearance for the action of a swinging door.
What is a double door set?
The door in a double-door set that does not contain a latch-set, but instead is bolted at the top and bottom to hold it stationary when shut. This door receives the latch or bolt of the active door.
What is a key in door knob?
Key-In Knobs or Lever. Knobs or levers that contain a cylinder on the exterior side that can be locked/unlocked by a key. The interior side has a thumbturn to operate the locking function. Key-in door knobs and levers are often combined with a deadbolt installed above it for best security.
What is a single dummy handle?
A single dummy handle indicates one handle that has no latching or locking function. It is surface mounted to a door simply to give the door a handle to pull it open. Single dummy handles are usually used on closet doors, bifold doors, or other doors where one handle is needed, but no latching or locking function is.
What is a dummy pair?
A dummy pair indicates a pair of handles that have no latching or locking functions . They are surface mounted to a door simply to give the door a handle to pull it open. Dummy pairs are usually used for the inactive door in a double-door set and other doors that need a handle on both sides, but no latching or locking function.
What is the direction of a door swing?
Door Swing. The direction the door opens while standing on the outside. If you stand on the outside of the door and you push it away from yourself to open, it is IN-SWING. If you stand on the outside of the door and you pull it towards you to open, it is OUT-SWING. (Back to top)
What is a door bore hole?
The large hole that is physically drilled through your door to allow for installation of hardware (such as a latchset like a door knob, lever, deadbolt, entry set, etc.). Bore holes are usually 2-1/8" in diameter.
What is the hole in a door latch?
The latch bore, also known as the edge bore, is the hole drilled from the side of the door into the cross bore to allow the latch of the lock to be installed and to accommodate the sliding of the deadbolt. The diameter of the latch bore is generally 1” to accommodate bolts from either mechanical or electronic locksets.
What is the trim on a door knob called?
Trim: Sometimes called a rose , the trim is a decorative plate attached to the door under the knob or lever. Depending on the lock you choose, there are a number of available trim styles and finishes to meet your specific preferences and that fit the uniqueness of your home’s look and style.
What is a faceplate on a door?
Faceplate. A metal plate on the edge of the door, next to the latch or deadbolt, the faceplate protects the lock from wear and tear. It may have rounded corners or be a circular drive-in faceplate. The shape of the faceplate used during installation depends on your door’s preparation.
What is a cross bore door?
The cross bore is the main hole drilled into the face of the door where the body of the lock (chassis) is installed . The latch bore, also known as the edge bore, is the hole drilled from the side of the door into the cross bore to allow the latch of the lock to be installed and to accommodate the sliding of the deadbolt. The diameter of the latch bore is generally 1” to accommodate bolts from either mechanical or electronic locksets.
