Full Answer
What is a handle puller used for?
The General Tools 180 Faucet Handle Puller allows you to remove stuck faucet handles from old showers and sinks. Its adjustable clamp design works on both small and large handle sizes up to 3" in length. The drive shaft is made from forged steel to hold up to lots of regular use.
How do you use a tap handle puller?
0:040:56Superior Tool Faucet Handle Puller - Easily Remove Faucet & Shower ...YouTubeStart of suggested clipEnd of suggested clipMake sure the feet of the tool are underneath the handle and the pin is located in the screw holeMoreMake sure the feet of the tool are underneath the handle and the pin is located in the screw hole and then simply twist in a clockwise motion. And the handle is removed from the faucet.
How do you remove a faucet handle without a puller?
Squirt a few drops of penetrating oil or spray lubricant into the space between the handle and the valve stem. Wait a few minutes, then tap the handle and try pulling it off.
How do you remove a faucet handle?
0:313:48How to Remove a Stuck / Frozen / Tight / Hard to Turn Price Pfister ...YouTubeStart of suggested clipEnd of suggested clipIt if your handle has some movement try spraying some wd-40 on the gap between the base and theMoreIt if your handle has some movement try spraying some wd-40 on the gap between the base and the handle. And wiggling it back and forth until it loosens.
What are the different types of faucet handles?
There are almost three types of faucet handles: lever handles, blade handles and cross handles. The type of handle that a faucet can accommodate is somewhat dependent on the type of faucet itself. Usually , you could see the double-handle or single handle in the market.
How do you loosen a stubborn tap?
0:402:42How to remove a stubborn tap head gear - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then also do is wrap it around their swords it's tight. And then put a piece of tape. On. JustMoreAnd then also do is wrap it around their swords it's tight. And then put a piece of tape. On. Just swirl it in place. And then all I do is get a box spanner. And slide that over the cardboard.
How do I remove a kitchen faucet handle?
0:402:02Stop Faucet Handle Leaking - How to Replace a Kitchen Faucet ValveYouTubeStart of suggested clipEnd of suggested clipWith the handle off you will be able to unscrew and remove the bonnet without tools this will exposeMoreWith the handle off you will be able to unscrew and remove the bonnet without tools this will expose the valve mounting nut. Now use your lock jaw pliers to remove the mounting. Nut.
How do you remove a faucet handle when the set screw is stripped?
Insert a cobalt drill bit into your drill. Use a bit that is just big enough in diameter to fit in the original screw head slots. ... Position the drill bit over the the first hole and drill out the screw head. Drill just enough to reach the inside diameter of the handle. ... Pull the faucet handle away from the faucet.
How do you remove an American standard faucet handle without screws?
0:466:13How To Fix A Leaking Faucet Without A Screw In The Handle - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt. Off once you get the cap off you can use a small flat head screwdriver to pop out the cartridge.MoreIt. Off once you get the cap off you can use a small flat head screwdriver to pop out the cartridge. Then it should just come out by. Hand.
How do you remove widespread faucet handles?
Widespread Faucet Handle Removal:Hold the handle with one hand. Using your other hand, turn the skirt, the decorative flared piece below the handle, counterclockwise. ... Remove any remaining components to expose the valve. ... The valve can now be replaced or other repairs made.Reassemble handle parts in reverse order.
What is the faucet handle called?
Faucet lever: This is the control for the water supply. You'll use this to turn water on and off during normal operation. Most kitchen sinks utilize a single lever that can be turned left or right to control the temperature of the water.
How do you remove a stuck Delta faucet handle?
It should just pull off. If it doesn't, you might try gently wiggling it side to side as you pull up. If you have a rubber or plastic mallet, you could try giving it a gentle tap to free it up. The trick is to be gentle enough to not break anything, but firm enough to knock it loose.
How do you remove a stuck mixer tap handle?
1:257:59How to remove the handle on mixer taps - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first thing to do is to get a color base make sure you've got it wd-40. And we're going to sprayMoreThe first thing to do is to get a color base make sure you've got it wd-40. And we're going to spray it straight in there at the head there in that hole.
How do you remove a lever tap head?
Open the tap up as far as it will go and then look directly at the opening under the crosshead. Located inside is a nut that can be reached with some circlip pliers. This is a tricky little job but once this is undone, the tap head should just lift away.
How do you unscrew a tap head?
How to Remove a Tap Head. To remove the tap head, simply prise off the tap indicator cover and remove the retaining screw beneath it. Once the screw is removed the tap head should then pull off. Occasionally, once the retaining screw has been removed the head of the tap will still not come off.
Product Overview
The Husky duel use Compression Sleeve and Faucet Handle puller offers a reliable way to remove seized 1/2 in. fittings. With its A3 steel design and zinc coating, this is sure to provide you with the leverage you need. This item is backed by the Husky lifetime warranty and satisfaction guarantee.
Info & Guides
You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.
