Removed Sections A section removed from its normal projected position in the standard arrangement of views is called a “removed” section. Such sections are labeled SECTION A-A, SECTION B-B, etc., corresponding to the letter designation at the ends of the cutting plane line.
What are removed sections and how do they work?
Just like any other view, Removed Sections provide the ability to break alignment, should you need to move the view to another area or show it in a different orientation. In the picture below, the removed section views have been aligned horizontally.
What is the difference between section view and removed section view?
Here the section drawing is rotated by 90 degrees from its actual position. A removed section drawing is when the section view is not positioned as projected from another view of the object. Removed sections are typically used when there are space constraints in the layout space.
What is the removed Section Technique in technical drawing?
The removed section technique is a very useful technique to show the important details of a complex part on the technical drawing sheets. To create a removed section from a part, you need to show the section as section A-A, section B-B, etc. on the main part. Then show the section cut view on the other part of the sheet to show additional details.
What is a half section?
Here is an object sectioned from two different directions. If the cutting plane is passed halfway through an object, and one-quarter of the object is removed, the resulting section is a half section. A half section has the advantage of showing both inside and outside configurations. It is frequently used for symmetrical objects.
What is a removed section in engineering drawing?
Removed Sections In Technical Drawings The removed section technique is a very useful technique to show the important details of a complex part on the technical drawing sheets. To create a removed section from a part, you need to show the section as section A-A, section B-B, etc.
What is the removed sectional view?
The removed section view is a zero-thickness slice through the model showing only cut edges and hatching perpendicular to the cutting line. That's different than the traditional section view, which is projected parallel to the cutting line.
What are the 7 types of section views?
There are a number of different types of sectional views that can be drawn. A few of the more common ones are: full sections, half sections, broken sections, rotated or revolved sections, removed sections, offset sections, and assembly sections.
What is a revolved section?
A revolved view is a cross section of an existing view, revolved 90 degrees around a cutting plane projection. You can use a cross section created in the 3D model as the cutting plane, or you can create one on the fly while placing the view.
What is the difference between full section and half section?
This is the most common section (called a full section) with the imaginary laser cutting a line across the entire construction, offering a view of a portion of the building with the rest of it put to one side. Half sections or views. In this type of section, only half of the space or object is cut away.
When should a full section be used?
Full sections This type of section is used for both detail and assembly drawings. When the cutting plane divides the object into two identical parts, it is not necessary to indicate its location.
What kind of section is imagined to be cut away quartered?
half sectionUsually, all visible edges behind the cutting plane should be shown. In a half section, ¼ of the object is imagined to be cut away.
In which type of section one quarter of the object is removed?
In this type of section, one quarter of the object is removed:1)Quarter section2)Half section3)Revolved section4)Removed section5)NULL
What is a section view?
A sectional view represents the part of an object remaining after a portion is assumed to have been cut and removed. The exposed cut surface is then indicated by section lines. Hidden features behind the cutting plane are omitted, unless required for dimensioning or for definition of the part.
What are the different types of sections?
Examples of different Section Types and how to use themHeadline.Row section.Columns section.Buttons section.Text + Buttons section.Grid section.Side-by-Side section.Tabs section.More items...•
What kinds of parts are usually not sectioned?
In addition to thin structural features, parts not sectioned also include standard mechanical elements such as shafts, bolts, screws, nuts, rivets, keys, pins, bearings, and gear teeth. The shaft, bolts, and nuts of the assembly are not sectioned even though they are cut by the cutting plane.
What is auxiliary section?
An auxiliary view is one that is projected on a plane other than one of the regular planes. A rectangular object is in normal position for regular multi-view orthographic projection when each of its faces is parallel to one regular plane of projection and perpendicular to the other two.
When is it possible to section an object?
It is possible to section an object whenever a closer look intentionally is desired. Here is an object sectioned from two different directions.
What is section lining?
Section Lining. The lines in the figure above, which look like saw marks, are called section lining. They are found on most sectional views, and indicate the surface which has been exposed by the cutting plane. Notice that the square hole in the object has no section lining, since it was not changed by sectioning.
What is a hidden line in a sectional drawing?
Hidden lines are usually not shown on the un-sectioned half unless they are needed for clearness or for dimensioning purposes. As in all sectional drawings, the cutting plane take precedence over the center line. Here is another example of a half section.
What is the process of sketching the internal configuration of an object by showing it cut apart?
The process of sketching the internal configuration of an object by showing it cut apart is known as sectioning. Sectioning is used frequently on a wide variety of Industrial drawings.
What is offset section?
An offset section is a means of including in a single section several features of an object that are not in a straight line. To do this, the cutting plane line is bent, or “OFFSET” to pass through the features of the part.
What is a cutting plane?
Cutting Plane. A surface cut by the saw in the drawing above is a cutting plane. Actually, it is an imaginary cutting plane taken through the object, since the object is imagined as being cut through at a desired location.
How far apart are section lines?
When sketching an object or part that requires a sectional view, they are drawn by eye at an angle of approximately 45 degrees, and are spaced about 1/8” apart. Since they are used to set off a section, they must be drawn with care.
When to use removed sections?
Removed sections are typically used when there are space constraints in the layout space. Most often the removed section does not show details of what is behind the cutting plane. The concept behind a removed section drawing. Source: makingthat.wordpress.com.
What is section drawing?
A section drawing is a view taken after you 'slice' an object, then look at the surface created by the slicing. An elevation drawing is a view taken from a point outside the object without any slicing. In both cases, the object should be standing on its base when the view is taken. Elevation Drawing Example.
What is longitudinal section drawing?
A longitudinal section drawing is when the cutting plane is along the larger axis of the object.
How to draw section of an object?
The best way to create a section drawing of an object is to use CAD (computer-aided design) software. There are several such software platforms available with varying capabilities, and the more the capabilities the higher the prices, which range from $30 to more than $10,000 (!!).
Why is a drawing on a separate sheet?
It is often drawn on a separate sheet to provide space for the dimensions which could not be fitted into the complex drawing. Sometimes several detail drawings will fit onto the separate sheet. The drawing below contains two detail drawings in circular outlines, magnifying parts of the larger drawing on the left.
What is section drawing in engineering?
Section Drawing in Engineering. Engineering objects often have complex inner structures, such as the inside of a jet engine. Like any modern-day objects, they are manufactured based on drawings with comprehensive details. It is frequently necessary for manufacturers to know what the inside of such objects looks like.
What does section line always end in?
The section line always ends in arrowheads. To understand how the section drawing is orientated in real space, imagine you are standing on the side of the parent object opposite the side the arrowheads point to .
What is a section break?
A section break is a line that divides paragraphs of text from each other. These breaks can help divide your paragraphs, graphs or entire sections of the document into separate parts. By using section breaks, you can divide your document into different sections. Each can have independent headers, footers, fonts and paragraphing styles.
Why is it important to remove section breaks?
It is important to remove section breaks because they can interfere with the formatting of your document. If you have a section break, the text before and after that break has different formatting principles in each. If you add a header to the text before your break, the text after the break won't have the same header.
Steps for removing section breaks in Word
If you want to remove section breaks from your documents, consider some of the following steps:
Benefits to removing section breaks in Word
Because section breaks are slightly larger than paragraph breaks, if you have multiple section breaks within your document, this could make your document longer than normal. Eliminating unneeded section breaks can help reduce unused space within your document, but it also reduces the amount of pages you need to print.
Remove Section and Page Breaks in Word on Windows 10
To get started, open the Word document that contains the section and/or page breaks that you’d like to remove. Once it’s open, you’ll need to locate the exact position of the section or page break in the document. To do so, click the “Show/Hide” icon in the “Paragraph” group of the “Home” tab.
Remove Section and Page Breaks in Word on Mac
On your Mac, open the Word document that contains the section and/or page breaks that you’d like to delete. You’re going to need to be able to locate the exact location of the breaks, so click the “Show/Hide” icon in the ribbon of the “Home” tab.
What is a continued revolved section?
Views, Continued Revolved sections Revolved sections are cross sections of an elongated form or object rotated toward the plane of projection to show its shape or contour. Drop a cutting plane perpendicular to the axis of the object and revolve the plane 90-degrees around a centerline and at a right angle to the axis.
Can you use a cross section in a 3D model?
You can use a cross section created in the 3D model as the cutting plane, or you can create one on the fly while placing the view. Likewise, what are the different types of section views? There are a number of different types of sectional views that can be drawn. A few of the more common ones are: full sections, half sections, broken sections, ...
