What is the difference between an so-238 and a PL-259 connector?
A double-ended SO-239 connector is designated as an SO-238. PL-259, SO-239, PL-258, and several other related military references refer to one specific mechanical design collectively known as the UHF Connector. In some countries, for example in Israel, the term 'PL connector' is confusingly associated rather with the analog phone connector.
What is the difference between SO-239 and UHF-female?
UHF-Female (or UHF-Jack) is THE SAME as SO-239. The above connectors are used in applications like amateur / HAM radio, CB / Citizens Band radio, Marine radio & VHF radio. Typically, the SO-239 (UHF Female/UHF Jack) is installed ON THE RADIO, and the PL-259 (UHF Male/UHF Plug) is installed ON THE CABLE.
What is another name for pl259 plug?
Sometimes the PL259 plug is also referred to as a UHF plug. PL-259 solder type with no spacer. Silver plated, silver plated tip and teflon insulator.
What does a PL259 connect to?
The PL-259 plug fits RG8U cable and, with suitable adaptors, RG8X and RG58. The PL259 connector mates with a SO-239 socket fitted to quality antennas. Suitable cables include RG-58 (smallest), RG-8X, RG-8U and RG213 - see Optimising VHF performance.
Are UHF and VHF connectors the same?
The design was named during an era when "UHF" meant frequencies over 30 MHz. Today, Ultra high frequency (UHF) instead refers to frequencies between 300 MHz and 3 GHz and the range of frequencies formerly known as UHF is now called "VHF".
How do you fit a PL259 plug?
1:142:30How to Install a PL-259 Coax Connection - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide the connector onto the coax. So that the tin connector fits through the center hole and screwMoreSlide the connector onto the coax. So that the tin connector fits through the center hole and screw the connector down over the braided shield until it's. Tight.
How do you solder a PL259 connector?
2:536:52Pl-259 Solder On Installation Guide for RG8X Coaxial Cable Full HDYouTubeStart of suggested clipEnd of suggested clipNow place a small amount of solder back onto the tip of the iron and touch it to the center pin aMoreNow place a small amount of solder back onto the tip of the iron and touch it to the center pin a special note make sure to heat the pin before touching and solder to it. Do not get impatient.
ARE SO 239 and PL 259 the same?
The above connectors are used in applications like amateur / HAM radio, CB / Citizens Band radio, Marine radio & VHF radio. Typically, the SO-239 (UHF Female/UHF Jack) is installed ON THE RADIO, and the PL-259 (UHF Male/UHF Plug) is installed ON THE CABLE. The two "mate" and are collectively known as a UHF Connection.
How do I know if my antenna is UHF or VHF?
If you see both V-shaped elements and a smaller cluster of straight elements on the same antenna, it receives both signals. The simplest indoor antenna is the basic rabbit ears design, which receives VHF. A loop-shaped antenna, whether it's arranged horizontally or vertically, is for UHF.
How do you hook up a coaxial cable to a CB antenna?
2:0211:30How to Properly Install a CB Antenna - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is my antenna coax cable. And then this here is a ground for the antenna bracket. And we'llMoreThis is my antenna coax cable. And then this here is a ground for the antenna bracket. And we'll talk about this in a minute I basically have this running through the tailgate.
Can you extend CB antenna cable?
Use the RG-58 coax cable when 18' just isn't enough! Our extended length CB coaxial is often used for base station installation and for long mobile applications, such as RVs and motor homes.
How do I connect my UHF coaxial cable?
1:122:25Rugged Radios: How to Install a UHF Connector - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull back the braided shielding being careful that no strands are making contact with the innerMorePull back the braided shielding being careful that no strands are making contact with the inner connector wires. Now slide the UHF connector over the coax cable being sure to get a tight fin.
How do you put an end on a VHF antenna?
0:467:25Soldering A PL-259 Connector For A VHF Antenna - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can use the razor knife or sharp pair of scissors to do that you want to cut back approximatelyMoreYou can use the razor knife or sharp pair of scissors to do that you want to cut back approximately 3/4 of an inch of the outer jacket. Taking care not to cut the shield underneath.
How do you solder RF connectors?
3:176:34How to solder Semi Rigid Coax - RG402 hardline - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext thing we want to do is just slide the connector shell over the cable and push until you push itMoreNext thing we want to do is just slide the connector shell over the cable and push until you push it into position. You can see there that the the pin is at the right length.
How do you solder a p259 connector?
11:3517:27Ham Radio Basics: How to Solder a PL259 Connector - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut remember you don't want this solder to flow all the way down. Into there where it's gonna touchMoreBut remember you don't want this solder to flow all the way down. Into there where it's gonna touch that ground she'll down in there. But you want enough that it's a good solid connection here.
What is the difference between a BNC and N connector?
BNC and N connectors are constant impedance and weatherproof. The BNC connector handles as much power as a UHF connector (500V peak) and is easier to connect and disconnect. The N connector handles more power (1500V peak).
Can UHF connectors cause problems?
Most of the time, UHF connectors will not cause any problems. If you have lots of connections, low-quality connectors, or are operating above 300 MHz, you should probably consider a more modern connector. I'm not sure what you mean by "M" type, but here are some points to address your question.
How many Ohms is a SO-239?
Virtually all of the impedance bump and loss is in the UHF female. A typical SO-239 UHF female, properly hooded, has an impedance bump of about 35 Ohms. The length of the bump is typically 1⁄2 inch, where the female pin flares to fit over the male pin.
What is a UHF connector?
The UHF connector is a name for a threaded RF connector. The connector design was invented in the 1930s for use in the radio industry, and is a shielded form of the " banana plug ". It is a widely used standard connector for HF transmission lines on full-sized radio equipment, with BNC connectors predominating for smaller, hand-held equipment.
