Full Answer
What can you do with Wiremold?
Explore Wiremold floor boxes, poke-thru devices, cable raceways and more. Think outside the wall. Bring power to open floor plans in commercial spaces where connections are necessary, but corners and walls are far.
What is Wiremold products trust?
Wiremold® Products Trust the industry's largest provider of end-to-end wire and cable management for indoor and outdoor applications. Explore Wiremold floor boxes, poke-thru devices, cable raceways and more. Think outside the wall.
What is Wiremold 700 series?
No rating value average rating value is 0.0 of 5. Read 0 Reviews Same page link. Wiremold 700 Series is ideal for surface mounting small amounts of electrical wiring or communication cables. This rugged raceway offers a low profile appearance which blend with any decor. Available in our exclusive ScuffCoat finish. Remove from favorites?
How to install Wiremold on the wall?
Once it is showing up as level, apply firm pressure to it until it is tightly sealed to the wall. Wiremold can be split at either the top or button depending on how you placed it. Take a small screwdriver to help you peel the edges apart and push the wire inside. When the wire has been run, push on the wiremold to close it back up.
What is Wiremold used for?
Product Details. The Legrand Wiremold 500 series raceway is ideal for surface mounting small amounts of electrical wiring or communication cables. Surface metal raceway allows you to add fixtures and outlets without disturbing the drywall, plaster or insulation in your home.
What is a Wiremold Raceway?
Wiremold® Raceway has defined the cable raceway category as an alternative to electrical conduit for close to a century. Attractive, cost-effective and an easy way to bring cables and wires to where they're needed—in virtually any room.
How is Wiremold installed?
7:218:18Wiremold: How to Install Metal Raceway - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe entire system must be grounded remove the existing ground wire from the green ground screw onMoreThe entire system must be grounded remove the existing ground wire from the green ground screw on the receptacle. Then cut to six inch lengths of new ground wire.
How do I get rid of Wiremold?
You might try rubbing what is left on the wall off manually, wearing rubber gloves. Or you can try scraping it off with a putty knife. If the wall has a gloss finish then you can also consider using an alcohol based solvent to remove the tape residue.
Can I run Romex in Wiremold?
Senior Member. Yes, NM cable is permitted in metal and nonmetallic surface raceways; however you must check the manufacturer's instructions for permitted number of conductors or cables and what cables and conductors are DESIGNED to be installed. Yes, the occupancy type makes a difference.
Is Wiremold rated for outdoor use?
The company states on the packaging that it is only rated for interior and dry locations. Also, the NEC (National Electrical Code) rates surface metal raceways for dry locations only. So, while it is easy to install and less visually intrusive when seen running along a wall than conduit, it should not be used outdoors.
What is a raceway in electrical terms?
The NEC defines a raceway as: “An enclosed channel designed expressly for holding wires, cables, or bus bars, with additional functions as permitted in this Code [Art. 100].”
Who makes Wiremold?
Legrand SAIn July 2000, French electrical manufacturer Legrand SA acquired the Wiremold Company for $770 million. Wiremold now works in cooperation with Ortronics, Inc, a Legrand-owned sister company based in New London, Connecticut.
How do you install plastic Wiremold?
2:013:43Wiremold: How to Install Nonmetallic Raceway - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor horizontal runs be sure to space the anchors 18 inches apart and install an anchor 1/2 inch fromMoreFor horizontal runs be sure to space the anchors 18 inches apart and install an anchor 1/2 inch from each end secure the base to both walls using the screws provided.
How do I remove Raceway?
To remove, slowly pull the raceway from the wall, using a wallpaper scraper or sharp knife behind the adhesive to slowly peel away… then for any additional residue left, use an adhesive removal spray.
How do you remove wire from casing?
0:352:38How to Strip Wire - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can buy a little cable stripper like this for three bucks at any home center just slide it overMoreYou can buy a little cable stripper like this for three bucks at any home center just slide it over the cable squeeze to puncture the sheathing. Then. Pull.
How do I install Plugmold?
1:414:31Wiremold: How to Install Plugmold Multi-Outlet Strips in Your KitchenYouTubeStart of suggested clipEnd of suggested clipWhen mounted the base should be flush to the surface. If you are joining two or more plugmold stripsMoreWhen mounted the base should be flush to the surface. If you are joining two or more plugmold strips connect the wiring harnesses between covers as follows cut to black white and green wires.
How do you use Wiremold Raceway?
4:508:29Wiremold: How to Install Metal Raceway - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide the elbow tongue onto the Raceway. Slide the raceway onto the starter box tongue tap the raceMoreSlide the elbow tongue onto the Raceway. Slide the raceway onto the starter box tongue tap the race into the support clip with the mallet. Then screw the flat elbow to the wall.
What color is Wiremold?
White color, but paintable. The Legrand Wiremold 700 series raceway is ideal for surface mounting small amounts of electrical wiring or communication cables.
How do you use Legrand Wiremold?
1:1715:27Simple Installation of Wiremold, Surface raceway - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay we're using an inch and a half box. Basically all you have to do is Mount this box to the wall.MoreOkay we're using an inch and a half box. Basically all you have to do is Mount this box to the wall. Run your wire through the conduit. Make your splice put your devices in put the cover on it you're
Who makes Wiremold?
Legrand SAIn July 2000, French electrical manufacturer Legrand SA acquired the Wiremold Company for $770 million. Wiremold now works in cooperation with Ortronics, Inc, a Legrand-owned sister company based in New London, Connecticut.
How small is a wiremold?
When selecting the type of wiremold you will use it is important to consider the number of wires you will be concealing inside of it. The smallest is ¼ inch. This will hold one standard low-voltage wire comfortably although you may be able to get two in.
What is wiremolding in a wall?
Level. Wiremold is a plastic molding which is designed to be attached directly to the wall with wires hidden inside of it. The main purpose of wiremold is to conceal wires in an attractive manner in situations where it is not possible to run the wire in any other fashion.
How to attach wiremold to wall?
Wiremold comes with preattached double-sided adhesive tape. There is a thin strip of plastic over this. Peel this plastic off. Line the wiremold up at the height you wish for the molding to be placed at. Gently attach the wiremold to the wall keeping it straight. Do not apply any pressure to it yet.
How to split wire on wiremold?
Wiremold can be split at either the top or button depending on how you placed it. Take a small screwdriver to help you peel the edges apart and push the wire inside. When the wire has been run, push on the wiremold to close it back up.
What connector do I need for a wire to go up and down?
If the wire is going around from one wall to the next wall, you will need a 90-degree L connector. To go up or down from the current level you will need a 90-degree connector. If you have sections which require two or more wiremolds to be in a line, you will also need an I connector to join them together.
What is a 700 series wiremold?
Wiremold 700 Series is ideal for surface mounting small amounts of electrical wiring or communication cables. This rugged raceway offers a low profile appearance which blend with any decor. Available in our exclusive ScuffCoat finish.
What is surface mounting?
Surface mounting. Eliminates disturbing the building structure or wall finish to make renovations easy.
Departments
At Lowe's, we have an extensive electrical department with all the tools and equipment you'll need to tackle any electrical project in your home. From electrical outlets and wall switches to battery chargers and generators, we've got the hardware to help you get your job done right.
Power Up With All Things Electrical
At Lowe's, we have an extensive electrical department with all the tools and equipment you'll need to tackle any electrical project in your home. From electrical outlets and wall switches to battery chargers and generators, we've got the hardware to help you get your job done right.
Product Overview
The Legrand Wiremold 700 series raceway is ideal for surface mounting small amounts of electrical wiring or communication cables. Surface metal raceway allows you to add fixtures and outlets without disturbing the drywall, plaster or insulation in your home.
Info & Guides
You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.
