CWF Oil Wood Stain provides a natural or tinted finish that protects wood from sun and water damage. Recommended for use on exterior wood decks, fences, siding, railings, outdoor furniture and other wood surfaces. May be used on new wood, pressure-treated wood, weathered wood and wood with a weathered solvent-based clear or semi-transparent stain.
Is flood CWF oil stain any good?
Flood CWF Oil Wood Stain Review. Flood CWF-UV 5 OIL is a high quality translucent, transparent and semi-transparent wood finish for exterior wood. It is a deep penetrating oil that is fortified with Flood’s Penetrol additive for maximum protection.
What is a CWF finish on wood?
FLOOD ® PRO CWF ® Penetrating Oil Wood Finish provides a natural oil-based finish that protects wood against moisture and sun damage. Fortified with PENETROL ® for excellent penetration.
What is CWF UV ready mix finish?
FLOOD ® PRO CWF-UV ® Ready Mix Penetrating Oil Wood Finish provides a natural finish that protects wood against moisture and sun damage. Fortified with PENETROL ® for excellent penetration.
What color does flood CWF UV5 stain look like?
– The Flood CWF-UV5 had a nice rich color when applied to the ACQ Pine decking. Golden with a hint of orange color. Knots were a little lighter in color than the rest of the deck but, that is normal for a true oil-based stain. Grain was highlighted well. – Color retention was decent.
Is CWF oil or water-based?
CWF® Oil Clear Wood Finish provides a natural or tinted finish that protects wood from sun and water damage. Alkyd/Oil resin provides the deep penetration of natural oils to enhance wood grain....Specifications.Available Sizes:1 Gallon/3.78 L , 5 Gallons/18.9 LVOC:Does not exceed 350 g/L2 more rows
How long does CWF last?
Top positive review Flood CWF-UV lasts for at least 6 years without the need for a recoat.
How do you apply a CWF stain?
Apply to a small area and allow stain to dry to ensure acceptable appearance. Apply one thin coat with a high quality brush, roller, paint or stain-pad, or with spray equipment. When applying by roller or spray, always back-brush for best results. Apply second coat wet-on-wet before the first coat has dried.
Can CWF be tinted?
CWF-UV can be tinted to 3 wood tones — Cedar, Redwood and Honey Gold. Recommended for use on any properly prepared exterior wood, including decks, fences, siding, railings, outdoor furniture, and other wood surfaces.
Is CWF a sealer?
CWF-UV® Clear Wood Finish provides a natural finish that protects wood from sun and water damage. retailers....Specifications.Available Sizes:1 Gallon/3.78 L , 5 Gallons/18.9 LDry Time:24 - 48 hours, depending on tempature and humidityVOC:Does not exceed 275 g/L1 more row
What is the best deck stain for pressure treated wood?
Best Stain for Pressure Treated WoodDEFY Extreme Wood Stain (semi-transparent)#1 Deck Solid Color Wood Deck Stain – (solid/opaque)TWP Stain (semi-transparent)
How long does it take CWF to dry?
24 to 48 hoursRemember, Flood CWF-UV is not a surface coating. It protects by penetrating the wood surface. For porous or older wood, if required, apply a second coat before the first coat has dried (within 20 minutes). Allow the finish to dry for 24 to 48 hours.
Can you spray CWF?
Apply an even coat with a brush, roller, or a low-pressure garden-type sprayer or spray equipment, avoiding heavy application. Application by brush is recommended. When applying by roller or spray, always back-brush for best results.
Does ppg own flood?
23, 2016 – FLOOD® wood care, a brand of the PPG (NYSE:PPG) architectural coatings business, today announced the launch of its new comprehensive Flood Pro Series line of professional stains, finishes and preparation products available exclusively at PPG PAINTS™ stores and independent retailers nationwide.
Is flood a good fence stain?
– The Flood CWF-UV 5 OIL is a decent stain. Better than most acrylic-based stains as this semi-transparent oil-based stain penetrates well into the wood grain. Little disappointing on the color retention and mold.
Can you add color to oil-based stain?
Stain and paint can be mixed safely to achieve your desired color. For successful results, mix oil-based stain only with oil-based paint and water-based stain only with water-based paint. You can also mix two colors of stain together to achieve the tint that you wish.
Can you add color to clear stain?
did you know that you can mix PAINT with stain? Sure you can! Just make sure that if you are using an water-based paint that you use a water-based stain. If your stain is oil-based you'll have to use an oil-based paint so that they will mix together.
How do you apply flood stain to wood?
0:000:30Apply Flood One-Step Wood Stain to Protect Your Deck - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor new wood use a wood cleaner brightener. Allow a minimum of two days for the wood to completelyMoreFor new wood use a wood cleaner brightener. Allow a minimum of two days for the wood to completely dry before applying the stain or use a product specially formulated to allow.
Is flood a good deck stain?
– The Flood CWF-UV 5 OIL is a decent stain. Better than most acrylic-based stains as this semi-transparent oil-based stain penetrates well into the wood grain. Little disappointing on the color retention and mold.
What is UV stain?
UV Plus is a penetrating deck stain, wood stain and oil finish that beautifies and protects exterior wood, providing a natural appearance. It is ideal for use on cedar, pine and redwood and comes in a variety of tones and semi-transparent colors. UV Plus contains fungicides and UV absorbers of the highest quality.
Where do CR test engineers stain?
To test wood stains, CR's test engineers apply two coats of stain to pine boards, then place them on the roof of our headquarters in Yonkers, N.Y. They face the boards south and angled down, like a roof, to intensify the effects of the sun and weather for up to three years.
How long does a semi transparent stain last?
But even the best semi-transparent stains in our tests aren't as tough as the top solid stains, and our data suggest that this type of stain will probably last only two to three years on a deck. The 11 stains in this category also vary widely in performance, garnering Overall Scores of 12 to 65.
How long does a deck stain last?
The best stains should last three to five years on a deck, and even longer if applied to siding or fences, which don't get as much abuse. "The sun and water beat down on a deck, snow can pile up, and even dirt and mildew spores can settle on the flat surface," says Rico de Paz, Consumer Reports' wood stain tester. "All those issues are minimized on a vertical surface."
Is Olympic Waterguard a good stain?
As a category, transparent wood stains, or clear sealers, don't fare well in our tests. The Olympic WaterGuard for Wood is the worst of the bunch, earning the lowest Overall Score in CR's stain tests—a 5 out of 100. It also earns a Poor for its appearance after one year in our simulated weathering test for decks, meaning this stain didn't take to the wood at all.
What is a solid stain for a fence?
While transparent and semi-transparent stains allow the finish and grain of the wood to shine, a solid stain helps to hide imperfections and signs of aging in the old wood.
What is Valspar fence stain?
Valspar Semi-Transparent Exterior Wood Stain and Sealer is a fence stain with sealer that provides color tone and long-lasting protection. This two-in-one formula saves even more time by only requiring a single application coat. As a water-based stain, you will only need soap and water to clean up brushes, spray equipment, and other tools. All things being considered, this fence stain with sealer is a quick and easy way to enhance your fence without the labor of applying multiple coats or products. The manufacturer backs this formula with a 6-year guarantee for fences when applied according to the product instructions.
What happens if you don't stain your fence?
Different than paint, fence stain penetrates into wooden boards to pigment the surface and, in many cases, protect the wood from exposure to UV rays and moisture. Without fence stain, your fencing may become dull, gray, splintered, and aged in a short period of time. When shopping for fence stain, you can either choose a formula ...
What is the best stain for cedar fence?
There are three opacity levels of fence stain: transparent, semi-transparent, and solid. Transparent fence stain is best for new wood, since the grain and condition of the wood will be easily seen. It’s also commonly used on cedar fences to highlight the natural color and beauty of this wood. Semi-transparent stains are a better choice for wood that is lightly aged or weathered, since they’ll conceal some aspects of weathering. Solid stain is best used on wood that is rough, splintered, and aged. This is the most opaque type of fence stain and will provide more coverage to give aged fence boards a uniform appearance.
How long does a fence stain last?
Most fence stains provide a limited warranty when used on vertical surfaces—like fencing. These warranties are usually for 4 to 6 years, with some formulas extending the warranty to 10 years or more. This will give you an idea of how long your fence stain may last.
How long does it take to stain a fence?
This can take as little as a month or might be as long as six months or more, depending on the environment. If you have softwood, you might consider doing a spot test to determine how porous the wood is and whether or not you should use a pre-conditioner to ensure even absorption.
How long does it take for a fence to dry before staining?
Allow the fence to dry for at least 48 hours before moving on to the staining process. If the fence is new, ensure that it has had plenty of ‘drying’ time and is ready for stain application.
What is a Kilz stain?
KILZ Exterior Waterproofing Wood Stain imparts a semi-transparent layer of color and protection to new and older wood decks that still allows the wood grain to show. Best of all, it’s available at an affordable price point in several popular hues.
What is the best stain for a deck?
Deck stain is available in four opacities: Toner: This stain is closest to a clear sealer. It contains just a hint of color and imparts only a slight hue to the wood that won’t change the deck’s overall look. Toner requires reapplication every year for the best protection.
How long does it take for a gallon of stain to dry?
For best results, apply only to clean, dry decking when the outdoor temperature is over 50 degrees Fahrenheit. Depending on humidity, dry time is approximately 24 hours. The stain comes in several size options, with 1 gallon covering about 200 to 400 square feet, depending on the thickness of the application.
What to consider when choosing a deck stain?
What to Consider When Choosing the Best Deck Stain. Choosing a deck stain is about more than just picking a color and brushing the product on the decking; the process requires considering the type and age of the deck wood and whether you’ve previously stained or painted it.
Can you stain a wood deck?
Photo: amazon.com. Harsh UV rays, battering rain, and temperature extremes can take a toll on a wood deck, leaving it faded and dull. Fortunately, staining a deck with a quality product can help revive its appearance while adding a measure of protection against the elements.
Is staining a deck the same as painting?
There’s a fine line between painting vs. staining a deck. The two products (paint and stain) are comparable and contain many of the same ingredients, but while stain is transparent and still shows the wood grain, paint covers and completely obscures the wood. Both products help preserve wood by repelling water and, depending on the brand, often include UV blockers and mildewcide to prevent mold and mildew growth.
