What is E-B emulsa bond?
Low Inventory Alert! Flood® E-B Emulsa Bond® is a latex-paint additive that helps alleviate peeling problems when painting over a sound but chalky or dusty surface. E-B Emulsa Bond® additive provides a bonding oil and stirs in easily.
Can you use emulsa bond on wood?
Use on wood, plywood, hardboard, T1-11, previously painted/coated surfaces (stucco, aluminum siding) and weathered but sound asbestos siding Always mix a small amount of E-B Emulsa Bond latex paint conditioner with the paint you are using to determine compatibility. Use only in the first coat of paint.
Can I mix E-B emulsa bond with latex paint?
Always mix a small amount of E-B Emulsa Bond latex paint conditioner with the paint you are using to determine compatibility. Use only in the first coat of paint. Do not add to gloss latex paints for one-coat work. You need Adobe Reader to view PDF files. You can download it for free if you don't have it.
What should I do before using emulsa-bond?
Always read the Emulsa-Bond (E-B) Product Information before using and follow the instructions carefully. Ensure the surface is clean and free from grease, residue, loose debris, or flaking paint.
What does Emulsa Bond do?
FLOOD® E-B EMULSA BOND® Latex-Based Coating Additive helps alleviate peeling problems when painting over a sound but chalky or dusty surface. It provides a bonding oil and stirs in easily.
How much Emulsa Bond do I need?
Normal ratio is 1 quart Emulsa-Bond to 1 gallon of latex paint. Paint may be applied by brush, roller, or spray. Paint can be topcoated in 4 hours or less.
What is Emulsa?
E-B EMULSA BOND® is a tough bonding primer for chalky exterior surfaces. Stir-in bonding additive for first coat. Improves adhesion of exterior water-based coatings to chalky wood, masonry or aluminum surfaces. Can eliminate priming step when added to first coat.
How much is a gallon of Emulsa bond?
32 oz.For latex house paint, add 32 oz. (1 qt.) E-B Emulsa Bond per gallon.
Do you add thinners to 2K paint?
Mix the paint: 2 parts paint, 1 part 2K Hardener then add 10% 2K Thinner to volume, this may vary depending on spray gun setup and air supply. Apply a cover coat of 2K paint, leave for 10-15 minutes, depending on conditions.
How do you use a paint adhesion promoter?
0:531:26How to Use Rust-Oleum Automotive Adhesion Promoter - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen applying adhesive promoter you want to make sure you keep the can upright. And at least 10 toMoreWhen applying adhesive promoter you want to make sure you keep the can upright. And at least 10 to 12 inches from the surface. And always work it in a back and forth motion just like.
What is EB for paint?
E-B acts as a stabiliser, penetrating deep into the surface to firmly bond the first coat of paint to the substrate, thus eliminating need for primer. Owatrol E-B provides a bonding primer, stirs in easily, and does not alter the original colour of the paint.
What is paint additive used for?
Paint additives are used to prevent defects in the coating (e.g., foam bubbles, poor leveling, flocculation, sedi- mentation) or to impart specific properties to the paint (e.g.. better slip, flame retardance, UV stability) that are otherwise difficult to achieve.
How much Owatrol do I add to paint?
Paint conditioner for wooden surfaces – mix 1 part Owatrol oil to 2 parts primer and apply as normal. Paint conditioner for wooden surfaces – mix 1 part Owatrol oil to 2 parts primer and apply as normal.
How many coats of bonding primer should I use?
Depending on how strong or bold the previous color is, it may be necessary to apply more than one coat of primer. However, it is not necessary to over apply the primer with so many coats. As long as the primer applies uniformly over the previous color, then one or two coats should be sufficient.
How many coats of 2K paint should I use?
Applying 2K Solid Colour Two to three coats are normally required, note 2K coverage is usually excellent. Spray gun set up will depend on your equipment. Normally a high pressure spray gun is used at around 45-50psi.
How long do you Inbetwean a coat of paint?
Adding a Second Coat After your first coat of paint is dry, it's safe to recoat typically after four to six hours. A good rule of thumb is to wait at least three hours to recoat your paint or primer if it's water-based. Waiting 24 hours is best for oil-based paint and primer.
What is Owatrol E-B?
Qty. Owatrol E-B is a high penetrating, stir-in paint additive for use in water-based masonry or interior paints. It will help alleviate peeling problems on all porous surfaces. Owatrol E-B is especially suitable for unstable, chalky and powdery surfaces, crumbling brickwork or render. E-B acts as a stabiliser, ...
How long to leave Owatrol E-B on paint?
Apply this to the affected areas, leave for 10-15 minutes, then rinse with clean water and allow to dry. • Shake container well. • Always mix a small amount of Owatrol E-B with paint to test compatibility. • Mix 1 part Owatrol E-B to 4 parts paint.
Does E-B paint work?
E-B greatly speeds up and simplifies the painting process, especially on difficult substrates. Mixing it with the first coat ensures a strong, wear- and peel-resistant bond without the need to apply a separate primer and then allow it to dry before you begin painting the final colour.
Does E-B bond with masonry paint?
Had to repaint a flaking asbestolux downpipe and, once cleaned of old paint, the first coat (with added E-B) seemed to bond really well with the surface. Client really happy with the results, too, which always helps!
Does Owatrol E-B need primer?
This, therefore, eliminates the need for primer. Owatrol E-B provides a bonding primer, stirs in easily, and does not alter the original colour of the paint. It offers a time-saving benefit by eliminating the need to separately prime.
Does Owatrol E-B work?
It will help alleviate peeling problems on all porous surfaces. Owatrol E-B is especially suitable for unstable, chalky and powdery surfaces, crumbling brickwork or render. E-B acts as a stabiliser, penetrating deep into the surface to firmly bond the first coat of paint to the substrate. This, therefore, eliminates the need for primer.
Bonding Primer & Paint Stabiliser
Owatrol E-B has been formulated to stop any peeling problems on all porous surfaces. It is a stir-in paint additive for use in water-based masonry or interior paints.
Properties
Provides a bonding primer and a first flat coat of masonry or interior paint in one.
Information
Coverage: Coverage will vary with the texture and porosity of the surface. Generally 20% less material is used than if the paint or stain had been applied without Owatrol E-B.
Frequently Bought Together
This item: E-B Emulsa-Bond 1-1-Qt. Acrylic Latex Off-White Stir-In Paint Additive
Product Overview
The Flood E-B Emulsa-Bond 1-Qt. Acrylic Latex Off-White Stir-In Paint Additive is designed to be used in exterior paints intended for wood, masonry and aluminum siding. It features a mildew- and UV-resistant, low-odor acrylic latex formula that is ideal for surfaces where adhesion is a concern.
Info & Guides
You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.
