The roll & tip method is a non-stop, fast-moving, two-person endeavor where one person applies a thin coat of paint with a roller, and the other person follows immediately behind with a brush to remove the roller stipple (‘orange peel’ texture) and smooth out the surface.
What does roll tips mean?
Rolling paper tips are a great way to help keep tobacco from getting into your mouth and to help prevent burning your fingers or lips. These cigarette tips are used on a rolled up cigarette where a filter normally would be. You simply take one piece and roll it up into a spiral and then place it in your rolling paper.
How do you roll and tip awlgrip?
1:388:34How to " Roll & Tip " an awl grip paint job - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow we're gonna start applying paint we're gonna use the rolling tipping method. First you roll onMoreNow we're gonna start applying paint we're gonna use the rolling tipping method. First you roll on your paint.
Do you need to roll and tip primer?
You can absolutely roll and tip the primer as well. In fact, the quality of the final finish coat is highly dependant upon getting the primer coat(s) on properly. You may not need a primer coat if you are going over a previous awlgrip finish that is still in good mechanical bond with the surface, but just faded, etc.
How do you roll tip like a pro?
0:391:55How-to Roll and Tip - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure to tip in the opposite direction of rolling. Tipping allows you to get rid of any airMoreMake sure to tip in the opposite direction of rolling. Tipping allows you to get rid of any air bubbles or small runs to ensure a beautiful paint. Job. Let the paint dry.
How do you roll and tip paint?
2:146:24How to easily roll and tip topside paint on your boat - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I roll and use quite a bit of pressure on the roller. And then I'll move over and roll it out aMoreSo I roll and use quite a bit of pressure on the roller. And then I'll move over and roll it out a little bit on the dry spot.
Can you buff Awlgrip paint?
Never apply or buff Awlcare with a machine. 2. Do not use abrasives or scratch pads to clean the surface. Scratching the surface gives dirt a place to cling while wearing out the resin layer.
Can you roll and tip metallic paint?
However, metallic paint can be successfully rolled as well, even by those with relatively little experience. Start by rolling the paint on the wall and then come back while it is still wet and lightly one-directional roll up with nothing more than the weight of the roller resting on the wall.
What is topside paint used for?
About Topside Paint Rust-Oleum® Marine Coatings Topside Paint provides gloss retention and UV resistance in extreme weather conditions. Apply to fiberglass, wood or metal surfaces above the waterline. Flexible formula is easy to apply.
Can you paint a boat with a brush?
Most people will use a standard “roll and tip” method for painting large surface areas of a boat. This requires two people and both rollers and brushes. As one person rolls out the paint, another follows behind with a brush and lightly strokes across the paint to brush out the roller pattern.
How do you roll a non skid Awlgrip?
0:502:21Creating a non skid surface using AwlGrip on a 23 mako - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe old grip grit I use a mixture of 50% coarse. And fine I have a bunch of holes poked into the topMoreThe old grip grit I use a mixture of 50% coarse. And fine I have a bunch of holes poked into the top of this so it's like a salt shaker. So I roll the paint. And then I sprinkle the non-skid.
Can you use Awlgrip below the waterline?
Awlgrip, or any other top coat paint, should not be used below the waterline.
Can Awlcraft be rolled?
So, Awlcraft 2000 is more suited for buffing and Awlgrip will require a Fairing Compound. Can be applied by spray or brush/roll.
How do you touch up Awlgrip?
Mix your Awlgrip HDT color as per product data sheet. Apply Awlgrip HDT over the damaged area, covering all of your 400 grit sand scratch on your first coat. Allow to flash off before applying your second coat. The second coat should be applied over your first coat and half way into your 800 grit sand scratch area.
What is rolling & tipping?
The roll & tip method is a non-stop, fast-moving, two-person endeavor where one person applies a thin coat of paint with a roller, and the other person follows immediately behind with a brush to remove the roller stipple (‘orange peel’ texture) and smooth out the surface.
Which direction should I roll & tip?
As far as what direction to roll and what direction to tip, the variations include: roll horizontally and tip horizontally, roll vertically and tip fore and aft (most common method for hulls or vertical surfaces), or roll fore and aft and tip vertically.
Tips for rolling & tipping
Whichever style you adopt, get into a rhythm and keep moving or the paint will dry and the brush will drag. If you run out of paint part-way down one side and stop to get more paint, you’ll get an ugly ridge at the point where you stopped and started up again. Don’t get discourage if the first coat is spotty or sags.
STEP 1. DEWAX THE SURFACE
For old Gelcoat Dewax and clean surface prior to sanding with a water based cleaner or a solvent. This very important step must be done prior to sanding. Sanding first will drive the wax into the sanding scratches. Water Based Cleaner: Use LBI 361 Verikleen or MaryKate MKT35 On/Off Cleaner.
STEP 2. SANDING
For Gelcoat in fair condition (not heavily damaged, just generally dull and faded) sand with 320 grit paper to completely sand the entire surface and remove all gloss. More coarse paper may open porosity (pinholes) in the old Gelcoat which will require more work to fill them.
STEP 3. PRIMING
You may want to apply Duratec primer to fair or coarse sanded surfaces as it will fill a lot of small imperfections and is very easy to sand. If the surface is pretty good and without the occasional deep sanding scratch apply the primer recommended by the manufacturer. This is a good time to practice you’re roll and tip technique.
STEP 4. FINAL SANDING
Completely sand the surface to at least 220grit (320 grit is better) use your finger tips to feel for imperfection as you sand. Touch is often better than sight. When sanding is completed clean off the sanding dust and gently remove the last dust particles with a tack cloth.
STEP 5. TOPCOAT APPLICATION
Mask as necessary and make sure the area is clean and dust free. The temperature of the area and surface to be painted should be 60 degrees F or above. The optimum temperature is 70 to 78 degrees F. If you have prepared a practice surface now is the time to perfect your technique. Use LBI WOR730-9 TIZ Roller and LBI RED12053 Onyx Brush.
