When is the best time of year to remove a tree?
That means if your tree has a pest, like emerald ash borer, or a disease like oak wilt, you should act fast. If your tree has a less severe problem, one of the best times to remove trees is during the dormant season, between late winter and early spring. Here’s why.
When is the best time of year to cut firewood?
Cutting in late September/early October has been the least amount of sap and lightest weight (easiest to handle) logs. Winter cut was not much different, but by late February the sap begins flowing.
What is the best time of year to cut logs?
Now as far as straight out cutting, it can be done any time of the year, but according to old carpenter's and sawyer's manuals, you get the best/most stable/whitest from logs cut in the fall to spring (cooler weather). Gene, that was interesting regarding the oxidizing.
When should I prune my evergreens for winter?
Never prune during early winters, as incisions could dry out if the temperatures drop below the freezing point. Unwanted lower branches on evergreen shrubs and trees need to be removed during later winters. Remove smaller or overgrown branches and increase the light and air at the crown of the tree.
Why do deer like hinge cut trees?
Hinge cutting makes open areas thicker and creates feeding, bedding and cover for deer. Hinge cutting also enables mast-producing trees to get more nutrients and water to produce more acorns and soft mast for the deer.
How many trees should you hinge cut?
2:4716:15Incredible Hinge Cuts For Deer Habitat - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou know for the majority of you should never be cutting at face high. So you're looking for treesMoreYou know for the majority of you should never be cutting at face high. So you're looking for trees up to six to eight inches in diameter. And. Those are gonna be the ones that you can hinge any hinge.
Is hinge cutting good for deer?
Hinge-cutting – which is the technique of zipping a saw halfway through a small tree then pushing it over so it stays alive but horizontal, providing cover and sometimes browse for deer – is a valuable tool for managing deer habitat.
How do you hinge a tree?
0:332:05How to make a perfect hinge when hinge cutting trees for deer habitatYouTubeStart of suggested clipEnd of suggested clipI'm just rocking it a little bit. I. Like that it's brushing through that other tree there from hereMoreI'm just rocking it a little bit. I. Like that it's brushing through that other tree there from here on it's going to come down pretty. Hard. This is a perfect hinge. This is a maple tree.
What trees are best for hinge cutting?
2:168:38Hinge Cutting Trees For Deer | What Trees To Cut? | Habitat ManagementYouTubeStart of suggested clipEnd of suggested clipNext up for a hinge cutting is a red maple one of the most widely distributed trees in a whitetails.MoreNext up for a hinge cutting is a red maple one of the most widely distributed trees in a whitetails. Range extremely important from a winter browse perspective. So in many cases not real high timber.
Can you hinge cut in the summer?
Hinge cutting trees is a great practice in late summer just as it is in late winter or early spring.
What happens when a tree hinges?
0:554:18Conventional tree felling Vs. Hinge Cutting - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen we do the back cut and this tree starts to fall this is gonna close up and when it meets itMoreWhen we do the back cut and this tree starts to fall this is gonna close up and when it meets it will pop this hinge.
How do you cut a hinge cut?
2:253:26How to Cut Perfect Door Hinges | Fast and Easy - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn. Always let your router come to a complete stop before you pull it out. And uh that's about it i'MoreOn. Always let your router come to a complete stop before you pull it out. And uh that's about it i'm gonna take this template off now by just turning this bolt. This twist head bolt.
Can you hinge cut aspen trees?
In All my experience with aspen, they regenerate better cut off completely than hinge cut.. Side note, if not very experienced, hinge cutting large diameter aspen is asking for an accident at some point from barber chairs..
How do you cut a tree so it falls where you want?
0:265:40How to Safely Notch a Tree for Direct Felling - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou have to leave wood in the middle you leave wood for hinge. That's what if you cut all the wayMoreYou have to leave wood in the middle you leave wood for hinge. That's what if you cut all the way through till you hit the notch. Then you've got no control in it and it'll fall on its own.
What is the proper way to cut a tree to fall?
Create a hinge in the trunk to steer the tree as it falls to the ground to ensure the tree falls the right way. To ensure your tree falls in the right direction, create a directional cut on the same side as you want the tree to fall. Next, make the felling cut by creating a horizontal cut from the opposite side.
How much hinge wood should be left when falling a tree?
The hinge holds the tree to the stump during most of the tree's fall, and it guides the tree in the intended direction. The length of the hinge should be 80 percent of the diameter of the tree. For example, on a 20-inch diameter tree, the hinge should be 20 inches x 80% = 16 inches.
What is the calculation for hinge wood?
It is recommended that the length of the hinge, measured perpendicular to the direction of fall, be at least 80 percent of the tree's diameter at breast height (DBH). How deep you go with the undercut will determine the hinge length.
How much hinge wood should be left when falling a tree?
The hinge holds the tree to the stump during most of the tree's fall, and it guides the tree in the intended direction. The length of the hinge should be 80 percent of the diameter of the tree. For example, on a 20-inch diameter tree, the hinge should be 20 inches x 80% = 16 inches.
What is the purpose of hinge wood?
The hinge is the wood between the undercut (face cut/notch) and the back cut. The purpose of the hinge is to provide sufficient wood to hold the tree to the stump during the majority of the tree's fall, and to guide the tree's fall in the intended direction. The position of the hinge will affect the direction of fall.
What is a triple hinge cut?
5:5511:30How To Tripple Hinge - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe idea of the triple hinges as it falls. This here wood will just kind of slide past each otherMoreThe idea of the triple hinges as it falls. This here wood will just kind of slide past each other you'll keep your fibers holding.
When is the best time to tap maple trees?
Indeed, sap moves at certain times of the year more than at other times. However, when tapping maple, the best time is likely in February before leaves are appearing.
What happens when maple is warm?
When warm, maple begins to oxidize, just like an apple turns brown after you take a bite of it. The oxidation reaction is more rapid as the temperature increases. Oxidation of maple can produce brown, pink and grayish colors. Also, when warm, the blue stain fungus is more active.
How long does it take to air dry 4/4 wood?
That is why air drying does not work well and leads to more problems with the boards. 4/4 boards take a year to air dry and the ambient humidity level is usually around 16%. Wood needs to be at 8% or lower for furniture and cabinet making.
How tall can a tree grow?
A tree can only grow about 430 ft from its roots. But if you go up a tree that is 430 ft tall and plant a tree in the crotch of a limb it will grow up 430 ft from its roots (just saying, I know the crotch will not hold it).
Does sap varies with the seasons?
The sap content varies very little if at all with the seasons. About the only variable you need to worry about is temperature, as some logs and lumber stain very quickly in warm weather.
Do sawmills work year round?
Sawmills generally work year round and the sawyer makes decisions based on each log as to what grades can be sawn. Proper handling in the stickering and air dry process greatly affect the degrade after sawing (twist, bow, checking, splitting, staining, etc.).
Can you cut wood during the rest of the year?
They said that if you cut them during the rest of the year, the wood is only fit for beams and other types of construction grade lumber. They said it has to do with the sap being down and that the wood will dry much faster and with less degrade. Forum Responses. (Sawing and Drying Forum)
