- Stir the Varathane thoroughly before applying it to the wood. Open the canister of Varathane and set it near your table.
- Load the Varathane onto a foam brush. Try using a 2 in (5.1 cm) foam brush for a consistent, controlled application.
- Drag the brush along the wood’s grain to apply the stainer. Start at one end of the wood and follow the grain toward the opposite end.
- Treat 2.15 sq ft (0.200 m2) sections at a time to prevent the stain from drying out. ...
- Wait 2 to 3 minutes for the stain to settle into the wood. ...
- Scrub off any excess Varathane with a cloth before it dries. Go back over the coated portion of the wood with a clean cloth.
Can I stain over Varathane?
Yes, as long as the Varathane wood stain has dried, you can apply Minwax polyurethane, polycrylic, or any other suitable clear coat over it. As they are rival companies, Minwax will only recommend you use their own products, but that isn’t necessary. The reverse of this is also true – you can put Varathane topcoats over Minwax wood stains.
Is Varathane wood stain oil or water based?
Varathane Water Based Wood Stains are formulated with premium pigments for clearer color. Varathane Water Based Wood Stains have been carefully designed to have the application and handling properties of an oil based penetrating stain with the ease of soap and water clean-up and low odor.
How long does water based Varathane take to dry?
Water based polyurethane dries very quickly and up to 4 coats can be applied in one day. Also to know, how long does varathane take to dry? Allow more time at cooler temperatures. Dries to the touch in 1-2 hours, dries to handle in 2 hours and can be recoated in 2 hours.
How long does Varathane take to dry?
The fastest drying Varathane polyurethane takes 2 hours to dry. When applied with an aerosol, it can be dry in just 30 minutes. The finished surface will be dry enough for light use after 24 hours and will be cured enough for normal use in 3 days.
How to apply varathane to wood?
Stir the Varathane thoroughly before applying it to the wood. Open the canister of Varathane and set it near your table . Varathane has a sediment in it that has to be mixed in so it doesn’t settle at the bottom. Use a wood stirring stick to swirl it around for 15 to 30 seconds. Make sure the Varathane is a uniform color with no solid sediment floating in it.
How long does it take for Varathane to dry?
Wait 2 to 3 minutes for the stain to settle into the wood. If you’re thinking that a couple of minutes seems like too short of a time for the stain to dry, you’re right. The Varathane will settle into the wood during this time, but it won’t begin drying.
What is Varathane stain?
Varathane is a special oil-based wood stainer created by Rust-Oleum. It can be applied to any piece of wood furniture to give it a deep, long-lasting finish. Before treating the wood, sand and clean it first. It will help the stain soak more evenly into the wood.
How to stain furniture without leaving inconsistencies?
Take any removable parts off the wood you’re staining. Staining a piece of furniture is far easier when you’re able to do it in parts. Make sure you remove anything that could get your way as well. Arrange the furniture so it’s accessible on all sides. That way, you will be able to cover it without leaving any inconsistencies in the finish.
How to get rid of discoloration on wood floors?
If that isn’t an option, spread a drop cloth or tarp over the floor and set the wood on top of it. Then, add protective plastic over any nearby walls or upholstery that could get dirty as well.
How to remove old wood finish?
Gently scrape the old finish from one end of the wood to the other. Press down with a light amount of pressure to avoid scratching the wood. The softened finish will peel off without difficulty. Make sure it is completely removed.
How to apply varathane to a table?
Brush the Varathane onto the table. Dip your brush into the Varathane. Wipe the excess off on the inside lip of the can, then use long, overlapping strokes to apply a thin layer to the table. Be extra careful around crevices and cracks. There should be no drips, unevenness, or pooling.
How to sand Varathane?
Sand the coat lightly with 220-grit sandpaper when dry. Now that the coat is dry, you can lightly sand its entire surface. If this is your first time working with Varathane, there may be some uneven spots. Aim for a smooth, uniform finish.
How to make varathane thicker?
Stir the Varathane to mix it. Shaking Varathane may cause air bubbles to form. Air bubbles can create a bumpy finish. Use a paint stirrer to mix the Varathane instead. If the Varathane seems especially thick, add a splash of mineral spirits to it as you mix.
How long does it take for a varathane coat to dry?
Test the coat for dryness. Oil-based Varathane will take 24 hours to dry; water-based ones only take 4 to 6 hours. After this time has passed, test its dryness by gently sanding an out of sight portion with 220-grit sandpaper.
How to prevent varathane drips?
Move your table to a well-ventilated work area. Varathane gives off fumes that can be dangerous if they build up. Choose a work area with good airflow to prevent this. You may want to lay out a drop cloth beneath the table to catch sawdust and Varathane drips.
What is varathane made of?
Varathane is a specific brand of polyurethane made by Rust-Oleum. By applying it to a table, you’ll create a clear finish that will protect and preserve the wood. This is a perfect way to showcase your table’s woodwork, and you can do it on your own. You’ll need to prep the wood by sanding and cleaning it before you can apply the Varathane.
What is the best varathane for wood?
Oil-based Varathane will be more heat resistant and durable. However, oil-bases usually have an amber tint that may hide the natural beauty of your wood. Water-based Varathane is better for showcasing wood’s natural beauty, but is less resilient. ...
How to apply varathane to wood?
Apply the Varathane in line with the wood grain and flooring boards. Begin against the end wall, at either side, working slowly across the room to cover approximately 5 to 7 feet of floor, depending on the length of your stroke. Coat the roller frequently with Varathane, and apply in long, smooth strokes, overlapping each stroke to eliminate drip ...
How long does it take for varathane to dry?
Allow the first coat of varathane to dry completely, for a minimum of 24 hours, or until the surface is no longer tacky to the touch. Use a floor buffer equipped with a polishing disc to buff the entire floor area. Buffing helps heat the finish to increase bonding and saturation into the wood.
What is a varathane floor?
Applying Varathane floor finish to a new or resurfaced wood floor enhances the beauty and texture of the wood, and provides a durable, low-maintenance protection from scuffs and scratches. Available in gloss, semi-gloss and matte finishes, Varathane's self-leveling formula makes it easy to apply, eliminates brush strokes and lasts for years. Applying Varathane requires using only a few tools and following a simple procedure.
