What is the front of a cabinet called?
The cabinet face frame is the front of the cabinet behind the door and drawer. It is typically make using solid wood but cheap cabinetry often uses staples for attaching the face frame. Cabinet door hinges are also a very important part of a cabinet.
What are the parts of a cabinet?
The part of the cabinet door that is cut in front. The part of the door that has a decorative design in the edges of the door. The drawer box is one of the main components of any kitchen cabinet. The drawer in a kitchen cabinet is used more often than the cabinet doors themselves.
Where is the frame on a cabinet door?
The piece of the cabinet’s frame structure located at the top and bottom of the door. The piece of the cabinet’s frame structure located on the left and right of the door. The part of the cabinet door that is cut in front.
What's the difference between a door and a cabinet?
A cabinet style where the doors fit inside of the face frame when they are closed (as opposed to sitting on top of the face frame which is what you have in a frameless cabinet). A cabinet style where the cabinet door or drawer covers all of the cabinet frame so that only the cabinet door is seen with no part of the face frame visible.
What are the parts of a cabinet?
Cabinet Face Frame. Cabinet face frames provide stability, keeping the cabinet box square during shipping and installation. ... Doors and Drawer Fronts. Doors and drawer fonts are one of the most prominent cabinet parts. ... Hinges. ... Drawer Glides. ... Drawer Box. ... Interior Finish Material. ... Cabinet Shelves.
What goes on the bottom of cabinets?
Toe Kick. The set back or cutout at the bottom of a cabinet that allows room for feet when standing in front of the cabinet.
What are the pieces of a cabinet called?
Cabinet doors are typically made out of five parts: two rails, two stiles and the center panel. Rails are the horizontal pieces and stiles are the vertical pieces. You can learn more about the different types of cabinet doors here!
What is the recess at the bottom of a base cabinet called?
A toe kick is a notch-shaped recess at the bottom front of a base cabinet. It provides a recess for your feet so you can get slightly closes to the countertop.
How do you finish the bottom of a cabinet?
0:072:20Moldings, Finish and Trim with Gary Striegler - Part 14 - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you go to a furniture store look any piece of furniture you're not going to see just a blank railMoreIf you go to a furniture store look any piece of furniture you're not going to see just a blank rail at the bottom there's always going to be some sort of ornamentation of a molding at the bottom.
How do I fix the bottom of my kitchen cabinets?
2:233:30How to replace rotted sink base cabinet floor bottom. Easy! Home ...YouTubeStart of suggested clipEnd of suggested clipCut ours at about 21 place the board's in the cabinet. And fit the seams together. If you cut itMoreCut ours at about 21 place the board's in the cabinet. And fit the seams together. If you cut it upside down you can have a nice finished cup without splintering. I'm using quarter-inch. Plywood.
What is a cabinet Mullion?
Mullions are the dividing bars that separate glass panes in a door, much like those found in window panes. For many years, mullioned glass cabinet doors were the most popular choice among homeowners, mostly because there weren't that many styles of glass-front cabinet doors available.
What does butt mean in cabinetry?
What is a Butt Door?
Cabinet doors that open towards each other are known as butt doors, thus named because of the way they butt together when fully open. This term can also be used to refer to double doors not separated by a center stile.
What is a plinth in a kitchen?
Kitchen plinths cover the space underneath lower cupboards, so there are no gaps or openings on show, giving a continuous and streamlined appearance. As well as providing a sleek, sophisticated finish, they can be used to introduce a subtle hint of colour that will complement individual taste and style.
What is a kitchen kickboard?
Kitchen Cabinet Kickboards or also knowns as kick plates are what keeps your cabinets off the floor and protected, by selecting the right colour and material it can also transform your kitchen's look.
What are legs and plinth?
Legs: The basic legs are plastic and adjust to help level the cabinets on uneven floor surfaces; the plinth strips hide these. There are also metal legs with screw-type adjustment and sturdy bases; these are more like furniture legs that you don't cover.
What is cabinet carcass?
The carcass is the framework of the cabinet itself, onto which doors are hung and drawers are fitted. An inferior carcass will not last and doors and drawers will sag in time. You may only see the carcass when a door or drawer is open, but the importance of quality materials can't be overestimated.
What is cabinet Gable?
It's \"the vertical triangular end of a building from cornice or eaves to ridge\".
What is a cabinet nailer?
Nailers refer to the structural pieces of the cabinet that fasten it to the wall. Stretchers refer to the structural pieces in the tops of the cabinets that replace the tops. The thickness of nailers and stretchers is entered into the "Material Thickness" standards window.
What are cabinet rails?
A cabinet rail is a long thin piece of wood that sits like a board or a beam. The top and bottom horizontal pieces are called the rails. Rails are combined with the vertical pieces of wood, which are called stiles. Every door frame in cabinetry has two rails, with one at the top and the other at the bottom.
What is center panel?
Center Panel – The raised or flat panel in the middle of a door enclosed by stiles and rails.
What is edge profile?
Edge Profile – Shape put on the outside edge of a door or drawer front.
What is a stile in cabinet doors?
Stile – The vertical-framing members of a cabinet face frame or cabinet door.
What is face frame?
Face Frame – The structural portion of the cabinet to which doors are attached, consisting of both rails and stiles.
What is the back of a cabinet?
Back – The rear vertical surface used to mount the cabinet to the wall.
What is an inset cabinet?
Inset cabinetry features doors and drawers which fit inside of the cabinet face frame opening.
What is an overlay cabinet?
A full overlay cabinet is one where the doors and drawer fronts completely cover the face frame.
What is a framing bead?
Framing Bead: the decorative inside edge of the door frame. Panel Raise Profile: the decorative cut made to the face of the of the raised panel, which highlights the fact that the panel is a separate piece from the framing. The panel can be either flat or raised.
What is a stile door?
Stile: Vertical piece of cabinet door frame, there is one on the left and right side of the door.
Can a cabinet box be framed?
The frame and the panel meet, and the panel is elevated above the frame. A flat panel is exactly as it sounds. The panel will just be flat, straight across. The actual cabinet box can be either framed or frameless.
What is a mortise and tenon?
Mortise and Tenon. The basic mortise and tenon is comprised of two components: the mortise hole, and the tenon tongue.This is not a common joint in kitchens but may be used in certain components like islands, kitchen desks, and bathroom vanities.
What is a full overlay cabinet?
Full Overlay. A cabinet style where the cabinet door or drawer covers all of the cabinet frame so that only the cabinet door is seen with no part of the face frame visible. ...
What is plywood in cabinet construction?
Plywood. Layers of medium to softer woods glued together to form a strong cabinet building material. The wood grains of each successive layer run at different angles, this creates strength that exceeds solid hardwoods. Relatively easy to work with.
What is face frame cabinet?
The frame adds strength to the box and the cabinet doors are inset into the face frame for a clean look. Face Frame cabinets differ from frameless cabinets by adding this wood frame around the front of the cabinet, frameless cabinets have no front face frame.
What is the term for a thin layer of vinyl that is vacuum pressed onto cabinet doors and drawer fronts?
Thermofoil. A thin layer of vinyl that is vacuum-pressed onto cabinet doors and drawer fronts that are typically constructed of medium-density fiberboard. Creates an easy to clean surface, wide range of colors and the option for high gloss finishes.
What is a base cabinet?
Base Cabinet. A cabinet that sits on the floor. These cabinets usually support the countertops. They differ from wall cabinets which hang on the wall. Base cabinets are typically 24" deep, and vary by width.
What is a cabinet that does not use a frame on the front edge of the cabinet?
A cabinet that does not use a frame on the front edge of the cabinet The front of the cabinet exposes the sides, top and bottom of the cabinet box, the full width and height doors then cover the cabinet box to the edges.
What is the difference between a full overlay and a partial overlay?
It is significant that you know what the difference between a full and a partial overlay is in cabinets, and also, what inset cabinets are. On a full overlay cabinet or drawers, the doors or drawers will cover the face frame completely. With a partial overlay, the cabinets are going to show some of the frame still.
Why are cabinet hinges important?
Cabinet door hinges are also a very important part of a cabinet. They hold the cabinet door up and are opened and closed thousands of times throughout their lifetime. It is always wise to buy high quality hinges due to the rigorous wear they go through.
What is frameless cabinet?
The cabinet’s frame can be either way, framed or frameless. Making the cabinet frameless will make it have more accessibility, ‘All access’. This type of structure is constructed without a face frame, having a thicker box structure, making it more stable.
Why are drawer slides important?
Drawer Slides. Drawer slides need to be high quality due to the rigorous wear and tear they go through when being opened and closed thousands of times throughout the years. Consumers can choose either traditional drawer slides or drawers with power outlet options called drawer outlet kits.
What is a flat panel door?
The part of the frame’s door that is given a cut on the raised panel, enhancing the fact that the panel is separated from the frame itself. This panel may also be flat. When the panel has been raised it will resemble the pictures of the door above. It shows that where the frame and panel come together, the panel has been elevated, and stands out from the frame. A flat panel however, is like it sounds, flat, and straight across.
Where is the frame of a cabinet located?
The piece of the cabinet’s frame structure located at the top and bottom of the door.
Is cabinet making confusing?
Knowing all of this a head of time can bring greater end results! After all, the process of cabinet making is not as confusing or befuddling as some may think. Of course, if you are a cabinet professional, you will most certainly want to learn as much about it as you can, and hopefully, this article has provided you with a little bit of knowledge into the world of making cabinets. I know I have learned a lot that I did not know before from it.
What is partial overlay?
If the face frame is partially visible under doors or drawers when closed , it creates a partial overlay. You can opt for a full overlay where all you see is the door, or a full inset where the doors fit flush within the frame. You’ll also find frameless cabinets with no center stile between doors, giving you all shelving with nothing in the way.
What are upper cabinets called?
If located above a stove, sink, or fridge, they’re often called bridge wall cabinets .
What is a blind corner cabinet?
If you have a corner where two cabinets meet at a right angle, a blind corner cabinet can help to maximize the space. You’ll often find a rotating circular shelving unit called a Lazy Susan within.
What is a cabinet frame?
Many cabinets have a layer of vertical and horizontal wood sections attached to the front edges of the cabinet box. This frame provides structure, strength, stability, and a place for the hinges of cabinet doors to be inset.
What is plywood used for?
More expensive than MDF or particleboard, plywood is commonly used in shelving, cabinet box construction and doors. • Laminate: Known as a countertop material, laminate often serves as a covering on cabinets. • Melamine: Much like laminate, melamine is a plastic-like product that covers cabinets.
What materials are used to build cabinets?
Cabinet construction materials. Manufacturers use a variety of materials to construct cabinets, including: • Solid wood: Solid wood cabinets use one piece of wood for each piece. You may see variations in the wood grain where multiple pieces join together.
What is semi custom cabinet?
Semi-custom cabinets are similar to stock, but with a limited selection of made-to-order features like custom shelves, racks, organization inserts, molding, and more.
What is Scribe molding?
Scribe molding is a thin piece of trim that covers any gaps between your cabinets and the wall. This is an easy way to solve any visible inconsistencies once your installation is complete. It's common for the walls and ceilings to be inconsistent if you're remodeling a kitchen in a historic home, so keep in mind that you might need ...
Why do you need risers on crown molding?
Riser molding helps raise the crown molding so it bonds with the ceiling. Some people like to show space above the cabinets to display decorative items, but if you rather close them off and avoid the buildup of dust, risers will help you close off the space if your crown molding isn't quite thick enough.
What is toe kick molding?
Toe kick molding covers the toe space of the cabinets to cover the exposed wood and allows your feet to stand closer to your workspace. This is both important for functionality and having a clean design. You can either use the same wood as the rest of your cabinets or use a color or material that pops against the rest.
Can you put molding on cabinets?
You can add molding to your cabinets in the same way you would install molding on your wall. Many cabinet companies sell pre-cut molding styles to fit the cabinets for sale, or you can purchase molding and make your own measurements and cuts. Then you simply have to nail and glue the molding in place, allowing the glue to dry overnight.
Can you add molding to kitchen cabinets after installation?
If you notice some unexpected gaps or feel like your cabinets are lacking design elements, you can always introduce molding to your kitchen after the installation without needing to alter the cabinets themselves.
Does crown molding help with spacing?
Cabinet molding can help customize your kitchen project by adding detail or the necessary support that your new kitchen cabinets need. You may have heard of how crown molding adds detail, but did you know that molding can also help guarantee spacing alignment and ensures that there is no exposed wood or noticeable sharp edges after installation?
Can crown molding be installed above cabinets?
Crown molding can either bond with the ceiling or allow for space above the cabinet. If you have high ceilings, we recommend leaving space below your ceiling so your cabinets aren't installed out of reach. x.
