What is a gutter drip edge?
Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components.
Should drip edge go over gutter?
It is recommended that gutters are placed under or 'behind' the drip edge of your roof. A drip edge refers to a component that hangs over the roof and has an outward projecting lower edge.
What are the 2 types of drip edge?
A drip edge is a type of angled roof flashing typically made with a metal like aluminum, copper, or steel. If installed properly, the drip edge is on the edges of a roof around the entire house. There are three main types of drip edges—L, C, and T—all differentiated by their relative shapes.
What is gutter apron used for?
A gutter apron is a specially designed drip edge folded at 120 degrees that helps direct water away into your gutter. We all know just how dangerous water seeping underneath your shingles can be, right? A gutter system that doesn't collect rainwater can be just as detrimental to your roof.
Why does rain run behind my gutters?
Water Gets Behind the Gutter If water is dripping behind your gutter, it's probably because it was installed without any flashing over the back of the gutter. The gutter apron will prevent the dripping. A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter.
What is another name for drip edge?
It's important to note that gutter apron and rake metal are often referred to as 'drip edge. ' This isn't necessarily incorrect, but it is a generic or slang term at best.
How do you install drip edge with existing gutters?
1:563:26How To Properly Install Drip Edge on your Roof -Jonny DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipBefore you mount it about a half inch. So you want about a half inch between the drip edge and theMoreBefore you mount it about a half inch. So you want about a half inch between the drip edge and the fascia a gap. So that the water just doesn't run off the edge onto your fascia.
Where should drip edge be installed?
The correct placement of a roof drip edge is on top of the roof's exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
How far should gutter be from drip edge?
How Far Should Gutters Be From the Roof Edge? The gutter should be installed as close to the shingles as possible; no more than 2 or 3 inches. If the gutter distance is more than 3 inches, the rain will run off the roof and won't drain properly.
How do you install drip edge after gutters?
1:474:03Gutter Installation tip "Drip Edge"#4 - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat's going to happen is the water is going to come off the edge of the roof stick to that dripMoreWhat's going to happen is the water is going to come off the edge of the roof stick to that drip edge and go behind your gutter and eventually it's gonna ride out your wood. So.
How far should shingles hang over gutters?
1/4 to 3/8 inchMost shingle manufacturers recommend a 1/4 to 3/8 inch overhang over your eave, which is where your roof ends by your gutter. In many cases, and particularly as the home ages and settles, the roof edge at the eave edge can wave in and out by more than this amount.
How do you extend shingles over gutters?
To fix an overhang that's too short, buy some aluminum drip edge (aka drip-cap flashing). It's typically sold in 8-ft. lengths, and can be cut with tin snips or even poultry shears. Slide the wide, flat flange of the flashing under the first course of shingles and adjust it to extend over the gutter.