What is a door strike on a door?
Definition of Door Strike in Construction. The door strike is located on the side of the door that accepts the swinging door when closed. The opposite of the hinged side, the door strike is the actual receptor of the lockset or latchset bolt mechanism that will secure the door closed when the door has hit the door stop.
What is the difference between hinged and strike plates?
The opposite of the hinged side, the door strike is the actual receptor of the lockset or latchset bolt mechanism that will secure the door closed when the door has hit the door stop. The strike plate is the plate, normally stainless steel or painted metal, that covers the opening in the door jamb that accepts the latching bolt on the hardware set.
What is a stop side door?
The term stop side comes from interior flat jambs that require a piece of material to stop the door from swinging too far and pulling on the hinges. The stop material is applied on the opposite side of the hinge.
What is the specialty side of a handed door?
When ordering a handed door, it is important to specify if the specialty side is on the hinge side or the stop side. The term stop side comes from interior flat jambs that require a piece of material to stop the door from swinging too far and pulling on the hinges. The stop material is applied on the opposite side of the hinge.
What is the Purpose of a Strike Plate?
How Do you Enlarge a Strike Plate Hole?
Do Door Knobs Come with Strike Plates?
Do Door Strike Plates Come in Different Sizes?
Where is the strike plate on a door?
The strike plate attaches to and protects the door jamb. This is the plate the latch-tongue, or deadbolt-tongue will connect with. It should sit flush with the door jamb. Any passage or privacy set needs to have a strike plate for the door to latch.
What is a strike on a door frame?
Strike plates help to keep your door tightly closed. They keep it securely in place until a lever or knob is used to open the door. A strike plate is fastened into the door jamb, guiding the latch into the receiving hole in the jamb, and holding it in place, all without needing to use your lever or knob.
Which side is the latch side of door?
Lock stile – This is the vertical edge of the door which sits on the opposite side of the door to the hinges, and contains the lock or latch.
What is the jam side of a door?
A jamb is the flat surface that runs vertically up either side of the door frame. The door jamb is vital to the running of the door. This is where the hinges are placed to hang the door, as well as the striker plate on the opposite door jamb which helps you to open, close and lock your door.
What is a lock strike?
Definition of lock strike : a metal fastening on a doorframe into which the bolt of a lock is projected to secure the door.
How do you measure a strike plate on a door?
The easiest way to determine what size strike you'll need is to measure from the center of the screw holes on the prepared jamb to the edge of the trim and then add ¼”. So, if your trim measures 1-1/2” from the center of where the screw holes are, you should order a 1-3/4” extended strike.
What is the gap between door and frame called?
Margins (sometimes also called “rebates”) are the spaces between the door and the door frame. These are often important if you're looking at issues with your hinge jamb. Again, these spaces can be broken down into specific types: the hinge margin, strike margin, top (header) margin, and bottom (sweep) margin.
What is a latch on a door?
Door latches are a type of mechanical hardware used to fasten doors and keep them shut. A door latch uses a fastener attached to two ordinarily separated surfaces, most often the door and the frame, to prevent the door from swinging while still allowing normal operation when the latch is released.
What is the hole on the side of a door knob for?
On the inside of that hole is a groove that will fit a small flat head screwdriver. Think of it as a very small screw that turns the lock. When you insert a small enough flat head screwdriver into this groove it will open your locked door.
What is the jamb side of a hinge?
The hinge jamb is the side where the hinges are installed, and the strike jamb is the side where the locking mechanism latches into the strike. The jambs are also used to mount the frame to the surrounding wall. The horizontal member that connects the two jambs is called the head.
What is the difference between a door jamb and door casing?
Door Jamb Basics They are vital for the connective element of a door with its doorway space. Now, it's important not to confuse door jambs with other components of the door frame. In particular, they are often mixed up with the door casing, which is the wood surrounding the door frame.
Are all door jambs the same?
Other Door Jamb Sizes Of course, there isn't a one-size-fits-all policy when it comes to doors. You may find that the measurements above are too large, or too small, for your opening. Other typical sizes for door jambs are: 4 9/16-inches if you have a 2x4 frame and a ½-inch drywall.
What is the purpose of a strike plate?
A strike plate is a piece of hardware that works with a lock to keep a door secure. Strike plates are installed on the door frame and contains a hole which receives the spring loaded latch or bolt which comes out of the latch or lock.
How do you fix a door strike?
Move the Strike PlateYou can move the strike plate up or down and in or out.Use a sharp chisel to enlarge the strike plate mortise. Then hold the strike plate in place and drill new 1/16-in. ... Install the strike plate and fill the gap in the mortise with wood filler. Remove the strike plate to paint or finish the patch.
What is a deadbolt strike?
A strike plate or "Strike" is a metal plate that is secured to the door jamb for the purpose of reinforcing the latch on the lockset or deadbolt. They come in many different shapes and sizes, for various applications.
How does a door striker plate work?
The door striker plates are installed in the door jambs, and precisely aligned with the door latches so that the latches catch onto the striker plate when the doors are closed.
What is a door strike?
A door strike is one of the primary components of a typical door locking system. Most regular doors have three major parts that work together to keep the door secure. The first two parts are the handle and the latch, both of which combined (along with several other smaller components) are commonly called the lockset.
How do door strikes work?
The door strike is fastened, usually by screws, onto the frame of a doorway, and it is carefully aligned with the lockset in order to give the latch a place to sink into when the door closes. Door strikes are designed to conform to the shape of the latch, as well as the thickness of the door frame. They help to protect the doorjamb from ...
What is a fail secure door?
With the fail-secure (a.k.a. fail-locked) configuration, applying an electric current will cause the door to unlock. Should a power outage occur, you can still utilize the mechanical lock on the secure side of the device to open the door. Fail-secure strikes are the ones that are commonly used for remotely buzzing in guests or customers. Electric strikes such as the World Strike 77V57 can be set to operate as either fail-safe or fail-secure, offering you premium flexibility. In addition, the 77V57 requires no special cutting or drilling into your door frame in order to install the device.
What is a fail safe strike?
The fail-safe (a.k.a. fail-open) configuration will cause the door to lock when an electric current is applied to the strike via a remote command. In this respect, the fail-safe strike operates somewhat similar to a magnetic lock.
Why are electric strikes used?
Electric strikes are commonly used in commercial access control systems, because they allow doors to remain locked on the exterior side in order to prevent public access. The main difference between electric strike plates and regular strike plates is that with an electric strike, the locking function is partially controlled by special mechanisms within the strike plate itself. Any time the release system is activated, a hinged piece of metal found inside the electric strike will pivot out of the way in order to allow the door to be opened without having to turn the door handle. A common example of this is a door that remains locked until someone “buzzes you in.” Electric strikes are often used for doors that are utilized in heavily trafficked areas.
What is a latch on a door?
The latch is the small metal bolt that you will see sticking out of the side of the door when the door is open . Latches are typically spring-loaded, and they lock into place when the door is fully closed, keeping the door secure.
What is an example of an electric strike?
A common example of this is a door that remains locked until someone “buzzes you in.” Electric strikes are often used for doors that are utilized in heavily trafficked areas.
Where is the door strike located?
The door strike is located on the side of the door that accepts the swinging door when closed. The opposite of the hinged side, the door strike is the actual receptor of the lockset or latchset bolt mechanism that will secure the door closed when the door has hit the door stop.
What is a strike plate?
The strike plate is the plate, normally stainless steel or painted metal, that covers the opening in the door jamb that accepts the latching bolt on the hardware set. The door strike side of the door is the opposite side as the hinged side and all the references of the strike and the strike plate will reference this location.
What is a door strike?
A door strike is one of the primary components of a typical door locking system. Most regular doors have three major parts that work together to keep the door secure. The first two parts are the handle and the latch. Both of which combined (along with several other smaller components) are commonly called the lockset.
Do you need special door strikes for going keyless?
The answer depends upon which type of keyless device you’re going to install. The majority of mechanical and electronic keyless locks available do not require any kind of special door strike, but there is a certain type of strike plate known as an “electric strike” that is unique in its function and application.
What is a sliding door?
Sliding doors. Doors and gates that do not extend to within 10” of the finish floor or ground. Existing doors or gates with kick plates (so long as cavities created by kick plates are capped) Tempered glass doors without stiles if the top edge of the bottom rail or shoe is tapered at least 60⁰ from the horizontal.
What causes a door to be recessed?
Thick walls, casework, shelving, columns and other elements can cause doors or gates to be recessed. If any obstruction within 18” of the latch side projects more than 8” from the face of a door or gate, maneuvering clearances for a forward approach must be provided. This space must be inset at obstructions so that it is no more than 8” from the face of the door or gate.
What is the maximum force required to open a door?
The 5 lbf maximum applies to the continuous application of force necessary to fully open a door, not the initial force needed to overcome the door’s seal resulting from unequal pressure. Latch bolts must be retracted and other devices that keep doors or gates closed must be disengaged prior to measuring the opening force. (Such devices, like other door and gate hardware, must operate with a maximum 5 lbf force (§404.2.7), but their operating force is not included in the measure of door or gate opening force). Door pressure gauges and other products are available to measure the opening force.
What are the requirements for a door in 404?
Requirements for doors, doorways, and gates in §404 apply to those that provide “user passage” (§206.5). Doors serving walk-in closets or pantries must comply. Doors to shallow closets or pantries, cabinets and other storage elements not providing user passage do not have to comply with provisions for doors, but must meet requirements for storage (§811), including those for clear floor space and operable parts.
How do low energy doors work?
Low energy doors and gates usually require activation by the user through a push plate or control and are often used in moderate traffic locations as an alternative to manual operation. Most function like a manual type but with a powered opener and closer option.
How high should a push gate be?
The bottom surface of doors and gates on the push side must be smooth to a height of at least 10”. This facilitates access since mobility aids, including wheelchair footrests, are sometimes used to push or prop open doors. Kick plates can be used to help protect door surfaces, but any gaps or cavities between the kick plate and the door surface must be closed or capped. Horizontal or vertical joints in this surface cannot exceed a 1/16” variation in plane.
How many inches separation is required for hinged doors?
At hinged or pivoted doors or gates in series, a separation is required that is at least 48” plus the width of doors or gates swinging into the space. This allows users to clear one door or gate before opening the next and applies to those doors or gates that are opposite each other where travel through both doors is required.
What side is the specialty side on a hand door?
When ordering a handed door, it is important to specify if the specialty side is on the hinge side or the stop side .
What is a stop side door?
The term stop side comes from interior flat jambs that require a piece of material to stop the door from swinging too far and pulling on the hinges. The stop material is applied on the opposite side of the hinge. Not all jambs use a separate piece of material. Some jambs have a built in stop, but the same concept applies.
What is a hand door?
A great example of a handed door is a louver door. The orientation of the door is associated with the blind side – or the side in which you cannot see into the next room or space.
Which way should a specialty door swing?
Swing. In addition to noting how the specialty door should be oriented, you will need to identify if the door will have a left or right hand swing. The stop or hinge side have no impact on which way the door needs to swing. Left Hand Swing.
What is the side with the hinge?
The side with the hinge is the Hinge Side while the side with the stop is the Stop Side. It is a good time to also mention another term that is often mentioned when it comes to units. The strike side references the side with the door knob.
How wide should a door be?
“Door openings shall provide a clear width of 32 inches (815 mm) minimum. Clear openings of doorways with swinging doors shall be measured between the face of the door and the stop, with the door open 90 degrees.”
How high should a door handle be?
The height of the door handle must be between a minimum of 34” and a maximum of 48”. A few exceptions are included in the bill. Things like:
What is the ADA door requirement?
Guide to ADA Door Requirements (Width, Clearance and Handle Guidelines) The Americans with Disabilities Act (ADA) is an American Law which was enacted in 1990. The legislation actually deals with the civil rights of individuals with disabilities. The law has imposed several guidelines and requirements on a number of different areas including:
How long does it take for a door closer to open?
Spring hinges are required to go from 70 degrees to completed closed in no less than 1.5 seconds.
Is clearance required for ADA door handles?
Clearance and maneuvering width is vital to the structural layout of a building, but the ADA doesn’t stop there. In addition to the components we’ve covered, there are also extensive ADA door handle requirements laid out in the legislation.
Where is the fixed table on a wheelchair door?
As you can see, the fixed table is right at the latch side of the door, leaving no space to maneuver for someone using a wheelchair. The required maneuvering clearance is addressed in both of the accessibility standards that are used in most US states – The ADA Standards for Accessible Design, and ICC A117.1 – Accessible and Usable Buildings and Facilities.
How much clearance is required for a push door?
For a front approach, the required maneuvering clearance on the push side of the door is an area that measures 48 inches perpendicular to the doorway; the 2017 edition of ICC A117.1 has increased this to 52 inches for new buildings. The required width of the maneuvering clearance depends on the door hardware. If the door has a door closer OR latching hardware, the required maneuvering clearance is equal to the door width. If the door has BOTH a door closer AND latching hardware, an extra 12 inches of maneuvering clearance is required beyond the latch side of the door.*
What is the Purpose of a Strike Plate?
As mentioned above, the position of the strike plate is essential to its purpose. There are three main functions of this part of the door.
How Do you Enlarge a Strike Plate Hole?
Your strike plate hole must be deep enough so that it can provide an adequate anchor to the latch or deadbolt. If it lacks depth, the bolt won't be able to extend fully, and your door won't stay closed.
Do Door Knobs Come with Strike Plates?
If you're buying a door knob, the set usually includes the strike plate, latch mechanism, mounting screws, and of course, both sides of the knobs. This makes it easier for you to install the knobs properly and make sure that they are ready for use right away.
Do Door Strike Plates Come in Different Sizes?
Because of the essential function that strike plates serve within a door, it is important to ensure that their fit is perfect.
