In thermodynamics, the Volume Correction Factor (VCF), also known as Correction for the effect of Temperature on Liquid (CTL), is a standardized computed factor used to correct for the thermal expansion of fluids, primarily, liquid hydrocarbons at various temperatures and densities.
Full Answer
What is volume correction factor (VCF)?
In thermodynamics, the Volume Correction Factor (VCF), also known as Correction for the effect of Temperature on Liquid (CTL), is a standardized computed factor used to correct for the thermal expansion of fluids, primarily, liquid hydrocarbons at various temperatures and densities.
What is the volume correction factor for gas?
The volume correction factor is used to consider the temperature, pressure and atmospheric conditions at a property. This factor is typically 1.02264 unless your property has unusual atmospheric conditions. Subtract the new meter reading from the previous read to work out the volume of gas used What should I do if I smell gas?
What is the correct volume correction factor for diesel blends?
Refer to bulletin V-18 for more information on product classes. Volume correction factors to 15 °C for use with all grades of diesel, bio-diesel and diesel blends (including B100) Temperature °C 0 0.10
What is the volume correction factor in the retail market procedures?
The system performs volume calculations and retrieves values for the following fields: Weight of Product, Primary Stock UOM (PSAU), Product Volume (Ambient), Product Volume (Standard), Volume Correction Factor. This value is the Volume Correction Factor as defined within the Retail Market Procedures.
What is the gas volume correction factor?
The volume correction factor is used to consider the temperature, pressure and atmospheric conditions at a property. This factor is typically 1.02264 unless your property has unusual atmospheric conditions.
What is VCF in oil and gas?
Volume Correction Factor or "VCF" means the coefficient of expansion for petroleum liquids at a given temperature and density. The product of the petroleum liquid volume, and the volume correction factor, equals the liquid volume at a standard temperature of either 60 degrees F or 15 degrees C.
What is corrected volume change?
There is a need for accurate natural gas measurement, and volume correction is the process of taking a gas meter's uncorrected volume and converting it to corrected volume based upon the effects of temperature and pressure. This correction increases the accuracy of natural gas measurement.
How is WCF and VCF calculated?
M. – T 54B (VCF) > Density @ 15*C 0.9903 = 0.9870 (see the above picture you need to interpolate if any different numbers on both columns). (Quick formula with reducing factor for WCF is Density @ 15*C – 0.0011 = 0.9903 – 0.0011 = 0.9892).
What is correction factor?
A Correction Factor (sometimes called insulin sensitivity), is how much 1 unit of rapid acting insulin will generally lower your blood glucose over 2 to 4 hours when you are in a fasting or pre-meal state. However, you should keep in mind: this is an estimate. it may need to change as your baseline dose changes.
What is corrected volume flow?
Corrected Volume is defined as mass over the density at reference conditions (eg at 0°C and 1013.25mbar; 1.29kg/m3 for air), thus it is a mass term. A volumetric flow rate with units of CFM or m3 implies that the flow rate was measured at actual conditions (actual pressure, actual temperature).
What is correction factor in heat exchanger?
The correction factor is a measure of the heat exchanger's departure from the ideal behavior of a counter flow heat exchanger having the same terminal temperatures. The correction factor depends on the efficiency of the temperature and the ratio of heat capacity for a particular flow arrangement.
How do you calculate volume change?
To calculate the change in volume we will subtract the initial volume from the final volume.
Examples of Volume Correction Factor in a sentence
Measurement Canada, Selection of Volume Correction Factor Tables and Standard Density Values for Some Common Products, Bulletin V‐18 (rev.
Related to Volume Correction Factor
Load Factor means the ratio of average demand for a designated time period (usually one month) to the maximum demand occurring in that period;
How to find the net volume of a liquid at 15°C?
To obtain the net volume of liquid at 15°C, multiply the uncompensated meter reading by the Volume Correction Factor (VCF) which corresponds to the average measured temperature of the liquid during the delivery.
What is the cubical coefficient of expansion at 15°C?
Cubical coefficient of expansion at 15°C = 0.001180 / °C
Most recent answer
Seem to me every country has its own specification, This just show the dangers of applying factors to a given tested result from some sort of specimen. Everybody above is correct with what they advise, but before you apply any factor think what you want to do and what you use, to get a result. Here are a couple of pointers.
All Answers (6)
According to North American standards, compressive strength is measured on cylinders with the length to the diameter (L/D) ratio of 2/1. With this ratio, the end conditions (friction and shear stresses at the contact surface with the testing machine) don't have a significant effect on the test results.
Similar questions and discussions
If I am using a standard drug which is not in a salt form and the formulation is in salt form (sodium, palmitate etc.) then I have to use the correction factor for the calculation. But if both the standard drug and the formulation are in the same salt form (ex.
