what saw to cut laminate flooring

Best Saw for Laminate Flooring

Full Answer

What is the best circular saw blade for laminate flooring?

Top 4 Best Circular Saw Blades for Cutting Laminate Flooring

• Freud D1216LF PCD Laminate Flooring Blade. ...
• Festool 496309 Laminate 48-Tooth Saw Blade. ...
• Freud D1084L 10-Inch Diameter 84t TCG Saw Blade (Editor’s Choice) The Freud D1084L Laminate flooring blade’s clean-cutting design ensures premium cutting results when working on hard laminate floors.
• Bosch DCB1072 Daredevil 10-Inch 72-Tooth Circular Saw Blade. ...

What are the best ways to lay laminate flooring?

• Remove the existing flooring, baseboards and moulding.
• Check that the subfloor is solid, flat and clean. ...
• If you are installing the flooring below grade or in a room with high humidity or moisture, such as a basement, lay down a vapor barrier before you install the ...
• Lay out the unopened boxes of laminate planks in the room. ...

More items...

How to cut laminate flooring with a Jigsaw face up?

Rules for laminate flooring or cutting with a jigsaw

• Set the electric motor of the jigsaw at the maximum speed while cutting the laminate.
• Please don’t cut it in steps, cut it at once.
• You must turn off the pendulum mode.
• Only use the blades which have been specially designated for the cutting of laminate. ...
• Thin blades will be more effective in their cutting.
• Before cutting, fasten the boards with clamps.

More items...

How to cut laminate with a jigsaw?

Requirement for Cut to Laminate Countertop with a Jigsaw:

1. Measuring & Marking: A tape measure is the most important tool in installing new laminate countertops. ...
2. Tape: Masking tape is a great way to prevent chipping on laminate surfaces by creating an expansion joint between the blade and surface.
3. Square: A square is a handy tool for cutting countertops and other materials. ...

More items...

What type of saw is used to cut laminate flooring?

What is the best saw for laminate flooring?

What is a bullet saw?

What is the difference between electric and manual flooring cutters?

How much does a flooring cutter cost?

Do you need a miter saw for angled cuts?

Can you cut laminate flooring with a saw?

See 2 more

What type of saw is best for cutting laminate flooring?

A jigsaw is a real all-rounder when it comes to cutting laminate floors. It's best used to cut out shapes from your board. For example, when you want to place boards around your toilet or maybe a pillar. Always use a fine toothed blade and have the saw blade spinning before you touch the board.

Do you need a special saw to cut laminate flooring?

If you are just learning how to cut laminate floors, understand that you don't need a special saw. In fact, you can cut the planks using a table saw, miter saw, circular saw, hand saw or laminate cutter.

How can I cut laminate flooring without chipping?

How to Cut Floor Boards Without ChippingMark and measure where you want to cut the boards beforehand with chalk or pencil.Keep your board in place using a stand or a clamp.Wear goggles, a mask, and gloves.Use a table or circular saw to make long, straight cuts. For angles, use a utility knife or a jigsaw.

What is the easiest way to cut laminate flooring?

0:011:49How to saw or cut laminate flooring | Tutorial by Quick-Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can actually do it with a regular handsaw. First make a short cut and then saw on but the sawMoreYou can actually do it with a regular handsaw. First make a short cut and then saw on but the saw line as close as possible to the bearing surface and clamp the loose piece down.

How many teeth blade for laminate flooring?

Straight Cuts A blade with a tooth count of 100 or more is best, and to reduce chipping, its leading edge always should contact the face of the board.

How do you cut laminate flooring cleanly?

0:131:44Cut Melamine With No Chips - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis. So I have my blade set to just barely pierce through the face of the melamine. And I'm gonnaMoreThis. So I have my blade set to just barely pierce through the face of the melamine. And I'm gonna make my first cut. So.

Do you cut laminate flooring face up or down?

The best technique for cutting your laminate is to cut downwards into it with the décor side facing upwards. The plank is then ready for installation.

Do I cut laminate from the top or bottom?

Always cut from the underside of a laminate countertop when using a circular saw or a jigsaw with a standard blade. This is because the blades cut as they come up through the material, and the top side (in this case, the underside) is much more likely to chip than the bottom side.

Can I cut laminate with a utility knife?

Since all plastic laminates are essentially the same, cutting Formica with a utility knife is identical to cutting most laminates. This method works well for one or two shorter cuts, but is too time consuming and inconsistent to use for larger projects.

What is the best tool to cut vinyl plank flooring?

Utility Knife Also known as a box cutter, a utility knife is the most common tool to cut vinyl plank floors. The knife is used to score the plank before bending the offcut piece to snap the plank across the scoreline using the score-and-snap method.

How do you cut laminate flooring by hand?

To cut laminate flooring, measure and mark the laminate's surface so you know where to cut, then use a circular saw or a handsaw with at least 18 teeth per inch to make straight cuts.

Do you cut the tongue off the first row of laminate?

Place the first plank with the tongue side towards the wall, being sure to allow 1/8" for expansion. We recommend cutting off the tongue on this first row to avoid any problem with the expansion gap.

Is laminate flooring hard on saw blades?

You see, laminate flooring will destroy a wood cutting blade with alternating top bevel (ATB) teeth in no time at all. The sharp points on this type of blade can't handle anything that hard – they dull quickly and those tips are what the blade uses to cut cleanly through wood.

Can laminate flooring be cut with a utility knife?

A regular utility knife blade can be used to cut flexible, self-adhering laminate strip material. The caveat is that you must change the blades frequently so the knife cuts properly -- a dull blade will not cut effectively.

Can I cut laminate flooring with a table saw?

Table saws produce straight, accurate cuts. Use them to make crosscuts against the grain of laminate flooring when you must trim boards to the proper length. Table saws are also great for rip cuts, made with the grain.

Will a circular saw cut laminate flooring?

For circular saws, they're best for making straight cuts in laminate floorings. Any other types of cuts will require a different tool. For example, a few curves in your laminate flooring will require a jigsaw. Circular saws, however, have greater tendencies to kickback when being used with thinner materials.

10 Best Saw For Cutting Laminate Flooring { Review 2022} - Pro Tool Guide

The Norske tools NMAP001 13 inch laminate flooring and the cutter is a newly improved saw with heavy duty aluminum, a fence, and a miter setting with a built-in precision angle.

How to Cut Laminate Flooring With a Circular Saw [2022]

When you’re certain that your measurements are precise, you can now place these marked laminate flooring boards on your sawhorses. Make sure to place the flooring correctly across this setup to prevent the possibility of incurring injuries or kickbacks, too!

What blades does Bosch use for laminate flooring?

Users can rely on these Bosch T503 saw blades for hardwood and laminate flooring projects. The affordable set comes with two hardwood blades and one laminate blade with each blade measuring 3¼ inches long. The laminate blade has 40 carbide-tipped teeth that cut smoothly through high-pressure laminates, while the hardwood blades have 35 teeth and a piercing tip to help start cuts on flat surfaces.

What is a Makita miter saw blade?

The Makita A-93681 miter saw blade is made with durable hardened steel that will resist bending or warping, even after extensive use. The saw blade is 10 inches in diameter and features an incredibly thin kerf that measures only .091 inches thick, allowing the blade to cut through flooring materials such as laminate with little resistance or strain on the saw’s motor.

What is the blade on a Norske miter saw?

The eight diamond-tipped teeth on the Norske Tools NCSBP284 miter saw blade are ideal for getting through hard materials like concrete and the abrasive wear layer of laminate flooring. The 12-inch laser-cut blade resists abrasion and features anti-vibration slots to help prevent the blade from jumping and reduce sideways movement while cutting.

What is a jigsaw blade?

The jigsaw blades are made with bimetal construction and they have an aggressive tooth pattern that cuts easily through tough material like laminate or deck boards. While these blades can make straight cuts, they are better suited for making curved cuts or small precision cuts in larger flooring projects.

What is a tungsten carbide blade?

The blade is designed for cutting through strong materials like laminate flooring, hardwood, and engineered wood flooring with its 40 tungsten carbide teeth that resist heat and abrasion damage. The thin kerf allows the blade to cut through laminates without a lot of material waste, and a lower hook angle on the teeth make the cut smoother. However, its thin profile can increase the amount of pressure required to cut through laminate flooring. The blade has a ⅝-inch arbor.

How many carbide teeth does a Bosch saw blade have?

This Bosch blade has 80 carbide-tipped teeth that resist impact and abrasion, helping it remain sharp for a longer time even while working with tougher materials like laminate flooring. The teeth on the saw blade have a negative hook design that doesn’t tear at the side of the laminate, so there is less risk of chipping.

What is a miter saw?

Miter saws have the benefit of being stationary, so it is easier to make straight or angled cuts with precision accuracy. For working with laminate, these saws use a blade that is shaped like a round cutting disc and typically has between 80 and 100 teeth that make smooth, fine cuts.

What is the best tool to cut laminate flooring?

Flooring Saw. The flooring saw is an effective way to cut your laminate boards when installing a floor. It combines the benefits of miter and table saws while offering more portability. This tool functions in the installation area so that you spend less time moving between the tools and floor while working.

What blade to use to cut laminate?

Following are some of the best blades to cut laminate flooring. Chose the right blade according to the arbor size and the type of power saw that you use to cut the laminates. 1. Freud LU79R010 – Circular Saw Blade for Laminate. This 10-inch circular blade from Freud works well on table saw, miter saw and circular saw.

What blades work well with a table saw?

This 10-inch circular blade from Freud works well on table saw, miter saw and circular saw. The 80 carbide tipped teeth cuts the laminate very smooth. It creates thin-kerf (3/32-inch), which is the main reason I recommend this blade.

What power tool to use to cut laminate?

This power tool gives you a vertical blade to use. That means you’ll need sawhorses or a stand to perform your cut correctly. Jigsaw works best if you need to cut a curve or angle into your laminate floor. If you clamp a board to a workstation, you could make some cross-cuts with this tool.

What brands of blades are used for laminate?

Brands like Bosch offer a three-pack of blades that let you tackle each aspect of your installation work. You’ll receive two that work with plywood, OSB, and natural products, with another made specifically for your laminate boards.

How many TPI should a jigsaw blade have?

If you purchase a jigsaw blade independently, it should have at least 20 TPI. Choose a design with a curve-cut edge that can handle the shapes you must install.

How to use a reciprocating saw?

If you have no other choice but to use a reciprocating saw, select a blade with the highest tooth count possible for your tool’s brand. Clamp the board firmly, but not to the point where you could damage it. Slowly run the blade through your line to get the cleanest cut possible.

What to do if your laminate blade isn't reverse cut?

Pro tip: if your blade isn’t reverse cut, flip your laminate piece over and make your cut line on the bottom. The upward slice of the teeth will spare the finish better than if you cut it normally.

What is reverse cut laminate?

This means that instead of cutting up through the piece, the teeth slice down into it – and any splintering or chipping should happen on the bottom side.

How to cut laminate with a pencil?

Step 1: Measure and Draw your Cut Line. Accurate cuts start with accurate measurements, and it doesn’t matter how straight your cut is if the line you’re following isn’t. Draw out your cut line on the laminate with a pencil or your grease pen following a straight edge.

How to make a curve in laminate flooring?

Step 1: Measure and Draw your Cut Line. Step 2: Place your Tape and Draw the Line Again. Step 3: Attach the Guide and Put on your Safety Gear. Step 4: Clamp the Board and Start the Saw. Step 5: Complete the Cut. How to Make Curved Cuts in Laminate Flooring.

How to prevent chipping on a blade?

Once you have your cut line, carefully place the masking tape on top – centering the tape on your line. You want a small margin of overlap on each side, and once your tape is set you can draw your cut line back on top.

What is the simplest cut?

Straight cuts are the simplest cuts you’ll make, but before you get to cutting you’ll want to gather the following supplies:

Can you use a cordless jigsaw to cut laminate?

They’re one of the safest saws to work with. The only drawbacks to using a cordless jigsaw are that they are less accurate for long, straight cuts and there is more potential to chip the finished surface of the laminate.

How many degrees can a miter gauge cut?

Its miter gauge allows you to perform three different angled cuts—0, 22.5, and 45 degrees—and the die cast aluminum rip fence adds to this model's durability.

How long can Norske cut boards?

The adjustable platform of this Norske cutter provides a sturdy work surface when dealing with long boards, and can extend up to 41 inches long. The 28.5-inch handle provides a ton of leverage when cutting too, and the wide blade has an impressive 13-inch cutting capacity.

Do you need a saw to cut vinyl flooring?

If you’re installing your own laminate, vinyl, or wood flooring, you’re going to need a flooring saw. These tools will allow you to create the necessary cross cuts, rip cuts, and miters. Although there are a couple dedicated flooring saws that are designed to perform all these cuts, this term can also refer to any type of power or manual saw being used on your flooring. Regardless of the type of flooring saw you use, make sure you’re using the appropriate blade for the material being cut.

Does the Worx saw have a laser guide?

While it's true that handheld saws tend to be less accurate and more prone to wandering off your cut line, this WORX model features a laser line guide to help minimize these accuracy issues.

Can you use a non-slip saw as a scroll saw?

Nonslip feet give the entire unit a solid, sturdy foundation, reducing the chances of slipping and making inaccurate cuts. You can even use it as a scroll saw if you need to make angled or irregular cuts.

Can you cut miters with angled cuts?

It won’t be ideal for cutting miters, though, so if you have a lot of angled cuts in your project, you may want to consider a different option.

Do you need a special blade for cutting vinyl?

You'll always want to consider the blade you are using. Depending on if you're cutting wood, laminate, or vinyl flooring , you may need a special blade to avoid damaging the material or the saw.

How to cut laminate with a circular saw?

You can easily wipe the chalk off the surface after you are done cutting. Leave the laminate facing right-side-up and cut it with a circular saw or handsaw.

How to cut curved laminate?

Cut out the curved shape. With a standard jigsaw blade, flip the laminate plank upside down. Place the pattern on the backside of the laminate, making sure to flip the pattern, so your cut laminate is positioned to come out correctly when the plank is flipped face up.

How to cut laminate face up?

If cutting the laminate face up, place painter's tape on the laminate along the pattern to keep it from chipping. Mark the cut line on top of the tape and cut with a jigsaw with a special blade.

What to wear when cutting laminate flooring?

Wear protective goggles and ear plugs or muffs while you cut laminate flooring. Also use a face mask to avoid breathing in the fine dust created from sawing laminate flooring.

How to make a curved cut on laminate flooring?

Make a paper pattern to help you make curved cuts and avoid wasting laminate flooring. Hold a piece of paper around the pillar or pipes and trace around the objects. Cut out the paper pattern, and then lay it back down to test for accuracy. This may take a few attempts to get the exact shape you want the laminate to be.

How many teeth per inch to cut laminate?

Article Summary X. To cut laminate flooring, measure and mark the laminate's surface so you know where to cut, then use a circular saw or a handsaw with at least 18 teeth per inch to make straight cuts.

Can you cut laminate flooring with a handsaw?

You might be able to get by with a handsaw for a small job. If you also need to cut laminate flooring in a curve, such as around pipes coming out of the floor or pillars, you'll need a jigsaw. Learn how to do both these methods by scrolling down to Step 1. Steps.

What type of saw is used to cut laminate flooring?

Moving away from the manual laminate floor cutters brings us to a sliding compound miter saw. A miter saw is excellent for angled cuts, if that’s what you need. The stainless steel miter detent has a total of 10 stops, which is more versatile when you cut laminate flooring compared to a guillotine-type saw.

What is the best saw for laminate flooring?

It’s no surprise that our team’s pick for the best saw for laminate flooring is a dedicated flooring saw from a reputable brand. The SKIL 3601-02 can handle laminate and engineered floors with miter detents so you can create angled cuts like a miter saw can. You can also make crosscuts and rip cuts with the help of a fence. The device is portable, solid, and reliable.

What is a bullet saw?

The Bullet Tools ES00-2009 is a siding and laminate cutter that is capable of cuts up to 9 inches wide and 9/16 inches thick. Because this type of laminate flooring saw does not require any electricity, it won’t generate much dust or noise, unlike electric cutters.

What is the difference between electric and manual flooring cutters?

Electric flooring cutters also cost more, and they are the complete opposite of manual cutters in the sense that they are noisy and messy , which will restrict your working hours and locations. The best saw for your needs will require you to weigh out the pros and cons of each type to decide.

How much does a flooring cutter cost?

Flooring cutters aren’t too expensive, with the most expensive models (depending on what type of saw you choose) being around 500. As our experts have said, the type of flooring saw will impact the price. Manual ones are cheaper and electric ones are higher in cost. The features, the quality, and the brand could affect the price tag as well, so these are all things you should consider.

Do you need a miter saw for angled cuts?

You then have miter saws, which can also make straight cuts but they are much better for angled cuts. You may not need to get a whole miter saw if your table and circular saws come with miter gauges. But just in case they don’t and you have miter saws in your arsenal, it’s useful to know that they make great flooring saws.

Can you cut laminate flooring with a saw?

You can either choose to cut laminate by bringing the boards to your saw or vice versa. However, sometimes it’s just easier to lug the laminate floor cutter around, especially if you’re in a large house or job site – this is where the portability comes in.