If your spreader is not listed in our guide, use this rule of thumb to determine your spreader setting:
- Place enough material in the hopper to cover 1,000 square feet. Place your spreader setting on a low setting (usually one-fourth of the spreader setting range or less). Spread the material over a 50 x 20-foot area (1,000 square feet). ...
- Keep in mind that it is always better to under fertilize than to over-fertilize and risk damage to the lawn.
What are some common Lesco spreader settings?
What Are Some Common Lesco Spreader Settings? Spreader settings for Lesco products vary according to pound concentrations per square foot, with settings divided according to letters, such as C1, D, E and G, and numbers, such as 9, 14, 15 and 16. These settings apply to standard grade spreaders. Lawn spreaders are designed to move fertilizer and ...
How to prepare a new seed bed for grass?
Preparing a perfect seedbed for new grass seed
- Mark out the area that you want to establish your new lawn seed with pegs and string.
- Decide whether it’s necessary to apply any weed killer, or if the soil is clean enough to begin cultivation. ...
- Next, you need to decide on how you will create your tilth. ...
- Decide if you want to apply a pre-seeding fertiliser. ...
How to set up a fertilizer spreader?
List of Fertilizer Spreader Settings
- Spreader Types. Calibration and fertilizer settings vary depending on the type of spreader. ...
- Drop Spreader Callibration. Initial calibration begins with marking off a testing area that will equal 100 square feet when multiplied by the width of the spreader's drop zone.
- Calibrating Rotary Spreaders. ...
- Application Amounts and Settings. ...
How to use a seed germination blanket over existing grass?
- Mow and rake the existing grass
- Prepare the bald or sparse patches of lawn ready for planting seeds, with tilling and adding fertilizer
- Measure the bald or sparse patches, and cut pieces of blanket to fit them
- Using seeds that are the same grass species as your existing lawn, sow them in the bare patches
- Cover these with the ready-cut pieces of blanket
What setting should my seed spreader be on?
Place your spreader setting on a low setting (usually one-fourth of the spreader setting range or less). Spread the material over a 50 x 20-foot area (1,000 square feet). If there is material left over, increase your setting. If you come up short, decrease your setting.
What setting should I use on my Scotts spreader for grass seed?
Since settings will vary based on seed, it's essential to verify this. For example, according to Scotts, the Scotts broadcast spreader settings for ryegrass seed should be set at setting 15 for new lawns and setting 5 for reseeding. Fertilizers will require a different setting as well.
How do you spread grass seed with a spreader?
0:041:36How to Lay Grass Seed | Lawn & Garden Care - YouTubeYouTubeStart of suggested clipEnd of suggested clipWould probably go down with say a quarter inch of space between the various seeds. You definitely doMoreWould probably go down with say a quarter inch of space between the various seeds. You definitely do not want to put down too much seed because even though that sounds good when the seeds sprout.
What setting should I set my Scotts spreader?
After choosing the best broadcast spreader for your yard, locate the orange dial on the spreader and turn it to the setting indicated on the seed or fertilizer bag. Turn clockwise for a higher setting of 12 or 14, which is for larger granules or grass seed, or counterclockwise to reach a lower setting of three or five.
What do the numbers mean on a seed spreader?
A spreader setting is the rate in which you apply product to your lawn. Each Jonathan Green product has recommended rates of application and coverage based on bag size. The application rate is defined as the amount of material applied per unit area of land.
Do you put fertilizer or grass seed first?
How soon after applying fertilizer can I plant grass seed? You can plant grass seed immediately after applying fertilizer. Please make sure there is no weed preventer in the fertilizer, as this will also prevent the grass seed from germinating.
Can you use a lawn spreader for grass seed?
At last, you can begin spreading seeds over the ground. You can do this by hand or with a lawn spreader. In either case, aim to deposit about 16 seeds over each square inch of soil.
How thick should you spread grass seed?
Most species should be planted at a shallow depth of ¼ to ½ inch. Larger seeds can be planted up to 1 inch deep. Most seedings are too deep if you cannot see a few seeds on the soil surface.
Can I just throw grass seed down on existing lawn?
By spreading grass seed over your existing lawn, you can thicken up the thin areas, and your lawn will start to look terrific again. (This is different from reseeding, which is when you start over and plant a completely new lawn.)
Can you use Scotts EZ seed in a spreader?
Answer: Per the manufacturer, Scotts EZ Seed Patch and Repair Sun and Shade should be applied with a spreader.
How do you use Scotts spreader?
0:231:32How to Use a Scotts® Broadcast Spreader on Your Lawn - YouTubeYouTubeStart of suggested clipEnd of suggested clipAt a steady pace apply a header strip counterclockwise. Around the outside edge of your lawn. ThenMoreAt a steady pace apply a header strip counterclockwise. Around the outside edge of your lawn. Then turn off the edge guard. And apply going back and forth inside the header strip in the longest.
What setting should I use on Scotts spreader for lime?
Pelletized lime should be applied every other year (approximately 15 lbs./1,000 ft²) once you have your soil pH to its optimum level, which is between 6.0 and 6.5....Lime.SpreaderSettingScotts (Drop)11.5Scotts (Broadcast)JEarthway EV-N-SPRED21Greenview3 or 45 more rows
Can you use Scotts EZ seed in a spreader?
Answer: Per the manufacturer, Scotts EZ Seed Patch and Repair Sun and Shade should be applied with a spreader.
Can you spread grass seed with a drop spreader?
Position your drop spreader near the edge of your yard and press the lever to engage it. Walk at a normal pace around the perimeter of your lawn to sow grass seed all along the edge.
How do you calibrate a Scotts broadcast spreader?
3:074:12How To Calibrate A Broadcast Spreader - YouTubeYouTubeStart of suggested clipEnd of suggested clipBegin your test run across the area that you marked off earlier. Be sure to give yourself enoughMoreBegin your test run across the area that you marked off earlier. Be sure to give yourself enough space to get up to speed before you reach the starting line. Once you hit that line open up the hopper.
Are Scotts spreader settings lbs per 1000 sq ft?
per 5000 sq. ft. or 8 lbs per 1000 sq ft.
Where to find spreader settings?
Spreader settings can be found on the "Details & Usage" tab on the product information pages. Or, you can use our spreader settings tool. If you still have questions, our experts are just a phone call away. Contact us at 1-800-543-TURF (8873).
Where to find spreader settings for Scotts lawn care?
Spreader settings for Scotts® Lawn Care products can be found on the product package. You can also find spreader settings on our product information pages (Lawn Food, Grass Seed, Weed Control, and Insect, Grub & Disease Control). Spreader settings can be found on the "Details & Usage" tab on the product information pages. Or, you can use our spreader settings tool. If you still have questions, our experts are just a phone call away. Contact us at 1-800-543-TURF (8873).
How many seeds can you distribute with a broadcast spreader?
How many seeds you’ll distribute with a broadcast spreader depends on two things: how fast you move and the size of the dropper hole. Some spreaders have adjustable holes to control drop rates. Even if your spreader doesn’t have this, you can still get a drop hole modifier.
What happens if you walk faster on a seed spreader?
The faster you walk, the more the wheels on this machine spins. The higher the spin rate, the higher the rotor speed and seed spread rate. These machines are more complicated to use than drop spreaders. Therefore, you should read the manual well before knowing about the drop rates and drop hole size adjustment.
How to control lime in Scotts broadcast spreader?
Scotts Broadcast Spreader Settings for Lime. One easy way to control lime application is by covering a spreader hole until only the 1/3rd part of it is open . Lime adds minerals to the soil and, if applied unbalanced, can wreak havoc on plant growth.
What does the number mean on a Scotts spreader?
What the numbers mean on a scotts spreader depends on one major thing; the type of spreader. If you’ve got a regular broadcast spreader, the number means Scotts spreader settings lbs per 1000 square feet area.
How does a drop spreader work?
A drop spreader works by dropping the seeds through a dropper. These droppers tend to be small, and this is quite helpful for working in space-constrained areas. A mini garden or a yard that isn’t too big can be easily covered with a drop spreader.
What is a Scotts spreader?
Before talking about the settings of a Scotts spreader, let’s have some ideas on some basics about spreaders in general; A spreader is a simple tool that has one main job: to evenly spread seeds and fertilizers on the ground. It can spread anything you want to apply in soil with consistency.
What are spreaders mainly of?
Spreaders are mainly of two types; drop and broadcast.