Use the remote control to adjust your pilot lights in these few steps:
- Turn on the pilot lights. The flames should burn blue and not orange.
- The remote control has an up and down button. Press and hold on to it until the fire goes out.
- Now adjust the flames to your liking by using the same controls. You can choose to lower or raise the flames.
What should a Pilot Light Flame Look Like?
How to see pilot flame on furnace?
What is the purpose of a pilot light?
What does it mean when a pilot flame is blue but weak?
Why is my furnace blue?
Why is it important to regulate gas pressure?
What color is a flame when oxygen is restricted?
See 2 more
What should pilot light look like furnace?
Your Furnace Needs a Cleaning Your pilot light should be bright blue, not red or yellow. A red or yellow flame indicates that your pilot light isn't getting enough fuel.
What color should a pilot light on a fireplace be?
blueThe color of the pilot light should be blue because that means that only natural gas—without any other condensates—is reaching the pilot light through the gas main. The principal chemical compound found in natural gas is methane, and methane burns blue.
Why is my pilot light flame yellow?
If you begin to feel unwell and your pilot light is burning yellow then seek medical assistance immediately. Yellow pilot lights mean that the gas-to-air mixture in your gas boiler is incorrect and that too much air is getting into the system.
What is the flame supposed to look like on a furnace?
The burner flames from your natural gas furnace should look blue or almost completely blue. A healthy natural gas furnace flame is characterized by a roaring blue flame with a light blue triangle in its center. There may be a tiny tip of yellow.
Should my pilot light be orange?
The flames from traditional pilot lights should burn a bright blue color. If your pilot light's flame is orange or yellow, it is burning inefficiently due to a lack of oxygen. The thermocouple should sense when this happens because the heat from the flame will not be as hot as it should be.
Is a pilot light supposed to be blue?
The pilot light should be a bright blue. The reason for this color is that natural gas consists primarily of the chemical compound methane, which burns blue. You might notice some slight red or yellow at the tip of the flame, but this is perfectly normal.
Should pilot light be blue or yellow?
blueInspecting a Gas Furnace Pilot Light Flame A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip.
How do you fix a orange flame on a gas heater?
Fixing Orange Flame On Your Gas Stove. Tips And RecommendationsDouble-check that all the burners on the stove are cleaned and placed correctly. ... Make sure that the burners of your stove have proper orifices.Check whether there is anything that clogs the orifices, and if you find it, remove the clog.More items...•
Should the flame touch the thermocouple?
The pilot flame should touch the thermocouple at a specific level. If the flame is blue and weak, and barely reaches the thermocouple, it needs to be stronger. If it extends well above the thermocouple, it's too strong.
What does a good flame look like?
A healthy, properly burning flame on gas appliances should be blue in color, sometimes with a tiny tip of yellow, with a little light blue triangle at the center. This blue color flame indicates that there is safe, efficient and more complete fuel combustion.
What does orange flame in my furnace mean?
When flames are yellow or orange it is a sign of dirt build up in the burner, or other possible issues. An unstable flickering yellow or orange flame is an indication that the furnace is not producing an appropriate mixture of gas and oxygen. Ignoring this sign can lead to a large gas leak and lead to disaster.
Is a blue flame safe?
Is a Blue Flame Safe on a Gas Fire? Since blue flames mean that your gas-burning object is working properly and efficiently, they are safe. The blue color is indicative that everything is mixing properly and burning hot. Any color other than blue or violet provides less heat.
What should my pilot light look like on my gas fireplace?
You should be able to clearly see the flame of the pilot light. The first thing to check is the color of the flame. A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip.
Should the pilot light always be on in a gas fireplace?
The pilot light needs to run continuously because, without it, the gas going into the fireplace would not have an ignition point. This would lead to fireplaces or entire gas fireplace inserts filling up with gas when they are turned on.
Is the pilot light on the gas fireplace always on?
The little flame you see in your gas fireplace after you have turned it off is called a pilot light. A Standing Pilot Light runs constantly, whether your fireplace is on or off.
Is it OK to leave the pilot on a gas fireplace?
Generally speaking, it is safe to leave your continuous pilot light on at all times, assuming it stays lit (more on this in a moment). While it does cost more to keep your pilot light on in between uses, it can actually have some benefits to your system.
My pilot light is way too high on my natural gas furnace after…
My pilot light is way too high on my natural gas furnace after changing the thermocouple tech said yes but should be okay (previously the pilot light was small and blue forever). Well 2 days in a row after restarting the furnace it built up pressure and overheated after about 7 hrs. Today we spent 1300 on all their suggested repairs and the same problem occurred 7hrs after completion.
How to Adjust the Pilot Light Flame on a Gas Furnace | Hunker
Adjusting the pilot light flame on a gas furnace is the best place to start, if it appears that your furnace is not getting as hot as it used to or if it seems like the flame goes out a lot. This is a very simple process and will only take a couple minutes.
How to Adjust the Pilot Light on Gas Logs | Hunker
Ideally, your pilot light should burn blue, but at times you'll find it's orange or yellow. You may also find the light burns too bright or dimly for your own personal tastes, which can also lead to increased soot buildup.
What causes the pilot flame to be yellow instead of blue. I… - JustAnswer
Hello and thank you for using this service, If the flame is too yellow there is not enough air. If you have just cleaned the pilot tube out a lot of times they will be yellow for a little bit. Now you need to take the pilot assy out to get it cleaned properly as the flame has to encompass the thermocouple bulb.
Pilot Light Lit But Burners Won't Ignite [6 Easy Solutions] - FireplaceHubs
The pilot light lit but burners won’t ignite! If this is the issue with your furnace, we bet you have an older model water heater. New models don’t include a pilot to ignite the heater or furnace.
Is There A Pilot Light On A Gas Fireplace?
Pilot lights are typically found inside gas fireplaces. The use of a pilot light helps to make the lighting of the main burner flames more efficient and effective. Pilot lights are a tried and tested component and have been incorporated into gas fireplaces for decades.
What Is A Gas Fireplace Pilot Light?
A gas fireplace pilot light is a small part that can be found as part of the ignition system for the fireplace and creates a smaller flame that’s used to help light the main flames generated by the larger burner. This pilot flame is required every time when lighting the main burner flames in a gas fireplace.
What Is The Pilot Position On A Gas Fireplace?
The pilot position on a gas fireplace is the position on the fireplace controls that is used to start the pilot flame. The pilot position is typically set on the control dial with either the dial depressed and turned, or used with a separate spark button to light the pilot flame.
What Happens If The Pilot Light Goes Out On A Gas Fireplace?
If the pilot light goes out on a gas fireplace the thermocouple and/or thermopile will help to shut off the gas supply. A pilot can be re-lit once it goes out but for gas fireplaces with standing pilot lights this re-lighting process may have to be undertaken after a short period of time.
Does A Gas Fireplace Pilot Light Use Much Gas?
The pilot light on a gas fireplace will use much less gas compared to the main burner. For electronic ignition gas fireplaces the pilot will turn off when the main burner is turned off. Gas usage for a standing pilot lights are small but can add up over time.
Why Does My Water Heater Pilot Light Keep Going Out?
It's pretty normal for a pilot light to go out every so often due to a normal fluctuation in gas pressure. But, once you get it relit, it should be fine again for a good period of time. If you light your water heater pilot light only to have it go out again a few minutes or hours later, that's a clear sign that something's not right—and that something is probably your thermocouple.
What Should a Water Heater Flame Look Like?
When you get your water heater pilot light flame back up and running, you should take a good look at it to make sure it looks as it should and everything is back to normal function. But what exactly is it supposed to look like? Your pilot flame should be mostly blue, and it might have a bit of yellow at the tip. There's not exactly a set height for the flame itself, it's more about how it is positioned in relation to the thermocouple. Basically, it should be covering about half an inch of the tip of the thermocouple. If it's not long enough to properly heat the flame sensor, or it's going too high, it will cause problems for the unit.
How Can I Make My Water Heater More Efficient?
The best way to keep your system running efficiently for as long as possible is routine maintenance services, but even a well-maintained unit that is nearing the end of its life is no match for the new, high-efficiency models on the market today. One way to help your unit run more efficiently is to add an insulating wrap to your tank. Just a simple foil "jacket" on the tank can help it hold in heat a lot better, which means it will use less energy keeping the tank hot.
How to see flame on pilot light on furnace?
Remove the furnace cover panel, which should expose the burner assembly and pilot. You should be able to see the flame of the pilot light.
What color is a pilot light?
The color of a healthy pilot light flame can vary a bit depending on whether your furnace uses natural gas or propane as a fuel. A natural gas flame should be a bright blue with the tip of the flame having just a tinge of yellow. A propane flame should have a bluish-green flame with a tinge of yellow at the tip.
What color is the flame on a propane burner?
A propane flame should have a bluish-green flame with a tinge of yellow at the tip. Remove the furnace cover panel, which should expose the burner assembly and pilot. You should be able to see the flame of the pilot light. If the pilot light is out, attempt to relight it.
Why is my furnace blue?
If the flame is too strong and improperly adjusted, it will be blue but may be noisy and lift off the thermocouple, causing improper furnace operation. If the pilot light is on, but the flame is a weak yellow in color, it will not get hot enough to heat the thermocouple to the proper temperature required to allow the gas valve to open.
How long does a standing pilot furnace last?
A lifespan of 15 to 20 years is typical for most forced-air furnaces, which means your standing-pilot furnace is nearing the end of its lifespan.
What causes a split flame in a pilot?
A split flame is caused by dirt inside the pilot tube. Take a needle or small nail and gently clean the tube. A flickering or wavering flame is usually caused by a draft. Check to see if there are obvious sources of drafts in the room.
Who is Bob Formisano?
Bob Formisano is a licensed architect and builder with 30 years of experience in the industry. Before the advent of modern electronic ignition furnaces, most gas furnaces featured a small standing pilot light that burned all the time. In such furnaces, the standing pilot works together as a team with the thermocouple ...
How does the pilot light works?
Gas fireplaces have the system of ignition based on the pilot light stand that provides flame and the thermocouple that sends an electric signal for the gas valve. When the pilot is on, the flame gives the right temperature to the thermocouple sensors and in its turn, the thermocouple gives the signal. These two devices depend on each other’s work. Thermocouple provides the signal that lets the pilot light stay on. The light provides the temperature needed for the thermocouple to work. This dependence is one of the main reasons for issues in the fireplace work.
How big should pilot light be?
To examine the work of the ignition system, first of all, see what does a pilot light look like. If it is too big or too bright it may give you a hint to the problem
Should I turn the pilot off on my gas fireplace during the summer?
Let’s explore the benefits and drawbacks of leaving the pilot gas on in the warm season.
What happens if the pilot flame is too long?
If the pilot flame is too long it will not reach the sensors and they could not ignite the system. Also, the bright orange light does not provide the temperature needed for the thermocouple to work. It probably would not cause any damage to the system, but it may have issues with the ignition.
What to do if your pilot light is too high?
So, if your pilot light flame also tends to be too high, ensure that your fireplace doesn’t have a button to bring the flame up or downward. If there’s no such button, adjust a screw on the fireplace.
Why doesn't my pilot light work?
Venting should work properly to provide enough oxygen to the system. Problems with the gas regulator or gas availability. These may be the reasons why the pilot light doesn’t work properly. Try to check each of them by yourself or get professional help for troubleshooting gas fireplace pilot lights.
What happens if the electric goes out on a fireplace?
The problem of the electronic ignition system is that if the electricity goes out you won’t be able to ignite the fireplace. The traditional fireplace ignition system is based on the pilot light. A pilot light is commonly used in many devices, like water heaters, stoves, and room heating systems.
What should a Pilot Light Flame Look Like?
The normal color your pilot light should be is deep blue, meaning it’s getting enough oxygen. It also needs to strong enough that it can cover half an inch of the thermocouple tip.
How to see pilot flame on furnace?
Take off the cover of the furnace panel which should reveal the burner assembly and the pilot. You should be able to view the pilot flame upon opening.
What is the purpose of a pilot light?
The main purpose of the pilot light is to provide a flame for the main burner system. Therefore, when the furnace is turned on, a valve will release gas in the burner and then the pilot light will ignite that gas.
What does it mean when a pilot flame is blue but weak?
Now, if you notice that the flame is still blue but weak and barely touching the thermocouple, then it means it needs to be adjusted to be stronger.
Why is my furnace blue?
Now, if you notice the flame is too strong and not adjusted properly, it is blue and noisy which can cause the furnace to function improperly.
Why is it important to regulate gas pressure?
It is important to keep an eye on gas pressure because once it starts to fluctuate then you could end up with some problems.
What color is a flame when oxygen is restricted?
When oxygen is restricted the flame will transform into a yellow color, with a lazy flicker.
