Full Answer
How to make a pocket screw joint?
- Set up jig depth and bit depth collar according to the material thickness.
- Align the drill guide to the edge where you need the pocket hole.
- Clamp securely to make sure there is no movement while you drill the hole.
- Drill the pocket hole.
What length pocket hole screws are generally used?
These screws have a narrow shank with a thread-cutting tip to avoid splitting hardwoods, and a strong head with a square recess for slip-proof driving. The most common length is 1-1/4 in., the best size for joining 3/4-in.-thick material.
How strong are pocket hole screws?
The superior strength of a pocket hole joint has actually been proven. Independent testing found that a pocket screw joint failed at 707 pounds when subjected to a shear load while a comparable mortise and tenon joint failed at 453 pounds - meaning that the pocket screw joint was approximately 35% stronger.
How to do Pocket screws?
Screw in the mounting brackets to the wall with a screwdriver or drill. Insert the rod through the rod pocket. Gently push the rod and try to avoid stretching or misshaping the valance.
What size screws are used for pocket holes?
There are 4 common thread lengths most commonly used, and they are 1”, 1 ¼”, 1 ½”, and 2 ½”. Again, the length of the screws you use will be determined by the depth of the drilling, and the depth of the drilling depends on the boards being joined.
What size are Kreg screws?
Kreg SPS-F125-100 Zinc Pocket Screws, 1-1/4 Inch #6 Fine Thread, Pan Head (100 Count)
Can you use any screws in a pocket hole?
1:275:42Will any screw work in a pocket hole? | MORE MINUTES - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is important because an advantage to using a pocket hole jig is that you only have to drill oneMoreThis is important because an advantage to using a pocket hole jig is that you only have to drill one hole in one board not in the receiving. Board that helps join the pieces together.
What size pocket screw do I need for 2x4?
What size pocket screws should I use for a 2×4? You should use 1.5″ pocket hole screws when joining a 2×4.
When should you not use pocket holes?
4:239:28When to NOT use pocket screws... and when you SHOULD! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd when you don't another place that you should definitely not use pocket screws is attaching aMoreAnd when you don't another place that you should definitely not use pocket screws is attaching a skirt to a table.
Do you need glue with pocket screws?
A:Technically speaking, David, pocket screws possess plenty of strength to hold a joint together without glue. So your joints likely won't fail from using pocket screws alone.
How long should screws be for pocket holes?
0:101:12Quick Tip: A Surefire Way to Check Kreg Screw Length - YouTubeYouTubeStart of suggested clipEnd of suggested clipAfter drilling a pocket hole which you can do in your workpiece or in a scrap piece that's the sameMoreAfter drilling a pocket hole which you can do in your workpiece or in a scrap piece that's the same thickness. Just drive in the screw you intend to use until it's seated in the pocket.
What can you use instead of pocket screws?
Alternatives to Pocket Hole ScrewsDrywall screws are one of the most common screw types, so you're bound to have some lying around. ... Cabinet screws are very similar to pocket hole screws and have nearly all of the same design features including wide washer heads, self-tapping tips, and partial threads.More items...
Why do my pocket hole screws stick out?
First, we need to be sure the drill bit and the drill guide are set for the proper thickness of our workpieces. Second, pocket screws will always stick out of pocket holes when they are drilled in ½” material. ½” material is just not thick enough to seat the head of the pocket screw below the face of the workpiece.
How long should a pocket hole screw be for a 2x4?
2-1/2″ Pocket Hole Screws for 2×4 Lumber Excellent Coarse Thread Pocket Hole Screws for use on Kreg or Castle Pocket Hole Systems. This is the wood screw for pocket hole joining 2×4 lumber (or other 2x dimensional lumber).
How far apart should pocket holes be?
6″ to 8″Pocket-hole spacing in plywood, panels, and long boards Whether you're drilling along the edge of long boards or you're working with sheet goods, our recommendations for spacing are the same. Place a pocket hole close to each end, and then space them out every 6″ to 8″ in between.
How are pocket holes measured?
0:051:10Kreg® 300-Series Pocket-Hole Jigs: Check Your Material ThicknessYouTubeStart of suggested clipEnd of suggested clipYou just need the material thickness gauge that comes with the jig. Simply hold the jig along theMoreYou just need the material thickness gauge that comes with the jig. Simply hold the jig along the edge of your material. And it will show you what thickness range your material falls in once.
Do you need special screws for Kreg jig?
Do you have to use Kreg pocket hole screws? You really do need to use Kreg screws when using the Kreg jig. The screws come specially designed to work with the holes that are drilled by the Kreg jig. Trying to use other screws will not properly bring the wood together.
How do I choose a Kreg screw?
0:061:18How To Choose the Correct Kreg Screw - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want a coarse thread screw those coarse threads will bite into these soft materials. And giveMoreYou want a coarse thread screw those coarse threads will bite into these soft materials. And give good holding. Power. For hardwoods like maple and oak you want a fine thread screw.
Are pocket hole screws different?
0:000:32Can you use regular screws in pocket holes? #shorts - YouTubeYouTubeStart of suggested clipEnd of suggested clipBoard tight. For this reason a regular screw won't work in pocket. Holes you.MoreBoard tight. For this reason a regular screw won't work in pocket. Holes you.
What size screws 2x2?
2x2's are actually 1.5" x 1.5", so the screw should be shorter than that distance plus the thickness of board you are using (1/2" or 3/4"), taking into account how far countersunk the screw is.
How Long Should Screws Be For Pocket Holes?
The length of the screw you use for pocket holes will depend on the jig setting and the depth of the drilling, each of which will depend on the boards being joined.
How Do You Size Pocket Holes in Woods?
When you’re joining workpieces of different thickness, the generally accepted rule is to think thin. When you set up the drill guide, the drill depth collar, and choosing the right screws for the different thicknesses, you should set it up to join the thinnest piece you are working with on your project.
Does the Wood Matter in Choosing Pocket Screws?
Pine, cedar, fir, and spruce, for instance, are softwoods, soft and not very dense. Plywood and MDF (medium density fiberboard) would fall into that same category when it comes to choosing pocket screws. The washer heads will help prevent overdriving the screws when you are joining particle board and plywood.
Should You Glue Pocket Holes?
It’s never a bad idea to take a belt-and-suspenders approach when you can. If you’re building a beautiful dining room table for your home and family, a bit of glue will give that little extra holding power to keep the joint from separating.
How To Fix Bad Miter Cuts
The two most common causes of miter cuts that just don’t fit the way we want them to is because:
How Do I Make Sure My Miter Saw Is Accurate?
There are several tests you can conduct on your miter saw to determine that everything is aligned properly to give you an accurate and true cut. Some inspections are obvious and results can make corrections and adjustments easy; some become a bit more involved.
How Do I Make My Miter Joints Tighter?
The surfaces of the wood being jointed in miter joints is end grain, and end grain soaks up glue very well. Gluing miter joints can last for years, even as the wood expands and contracts, since all of the pieces will expand and contract together.
What is a Kreg pocket hole screw?
The answer is that Kreg Pocket-Hole Screws are engineered for pocket-hole joinery, with specific features that ensure the best performance.
What type of screws are used for softwoods?
Coarse-thread screws for softwoods. Woods like pine and spruce, for example (known as softwoods), are soft and not very dense. That means they need a screw with deep, aggressive threads that will bite into those soft fibers. Coarse-thread Kreg Pocket-Hole Screws work great for these woods.
What is a blue kote screw?
Blue-Kote™ Kreg Pocket-Hole Screwsare the best choice for damp or wet applications, including projects for your porch, patio, detached garage, or outdoor areas. These screws feature 3 anti-corrosion layers to help them resist corrosion in wet areas for the long haul.
What is pocket hole jig?
The pocket-hole screw is actually what holds your pieces together to create a strong, long-lasting joint.
Why use pocket hole screws?from quickscrews.com
It’s important to use pocket hole screws to prevent damage, or a weaker hold when your project calls for it .
Can you hide pocket holes in a Kreg joinery?from learn.kregtool.com
But for any that can’t be hidden, or if you just want to plug the holes, it’s easy to do by using pocket-hole plugs.
What is a Kreg pocket hole screw?from learn.kregtool.com
The answer is that Kreg Pocket-Hole Screws are engineered for pocket-hole joinery, with specific features that ensure the best performance.
What type of screws are used for softwoods?from learn.kregtool.com
Coarse-thread screws for softwoods. Woods like pine and spruce, for example (known as softwoods), are soft and not very dense. That means they need a screw with deep, aggressive threads that will bite into those soft fibers. Coarse-thread Kreg Pocket-Hole Screws work great for these woods.
What is a blue kote screw?from learn.kregtool.com
Blue-Kote™ Kreg Pocket-Hole Screwsare the best choice for damp or wet applications, including projects for your porch, patio, detached garage, or outdoor areas. These screws feature 3 anti-corrosion layers to help them resist corrosion in wet areas for the long haul.
What is pocket hole jig?from learn.kregtool.com
The pocket-hole screw is actually what holds your pieces together to create a strong, long-lasting joint.
Pocket Hole Anatomy
When it boils down to it, there are three different things to consider when choosing pocket screws: Length/size, Screw Type (coating), and thread size.
Screw Length and Diameter
As you can see in the cut-away above, a properly sized pocket hole screw is just below the surface of the part. If you choose a screw that’s too long for your project, it’s going to zip through the face of one of your parts. Likewise, a screw that’s too short will not offer sufficient holding power.
Thread Size
Now that we’ve decided length of the screw you need, now you have to decide whether you want coarse or fine threads on the screw. And you might think “Of course I want coarse threads … They’ll hold better.” Well, yes and no. Coarse threads are indeed larger and hold better in softer woods.
Screw Coating type
The final consideration to give to your pocket screw is what type of project are you building? What I mean by that, is the project going to be exposed to weather? If it will, then you’ll want to make sure that your pocket hole screws have some form of protective coating on them.
How do you orient pocket holes?
The orientation of pocket holes is not as important as their placement. However, if you are using pocket screws to join two pieces of wood at right angles, the holes should be drilled perpendicular to the surface of the piece being joined.
What angle does a Kreg jig drill at?
The Kreg jig drill has a depth stop that limits how far the bit can go into the workpiece. The jig can be set to drill at any angle between 0 and 90 degrees.
How do you use a Kreg jig on a 90 degree angle?
Set the Kreg jig to the desired depth, then clamp it to the workpiece. Drill a hole at the end of the workpiece, then insert a screw to secure the jig in place. Drill pilot holes in the workpiece at the desired angle, then insert screws to secure the workpiece to the jig.
Do you need glue with pocket screws?
No, you don’t need glue with pocket screws. The screws should be long enough to go through the pocket hole, the plywood thickness, and into the second piece of plywood.
Do you need special screws for pocket holes?
Yes, pocket holes require special screws that are designed to grip the inside of the hole.
What is a Kreg pocket hole screw?from learn.kregtool.com
The answer is that Kreg Pocket-Hole Screws are engineered for pocket-hole joinery, with specific features that ensure the best performance.
What type of screws are used for softwoods?from learn.kregtool.com
Coarse-thread screws for softwoods. Woods like pine and spruce, for example (known as softwoods), are soft and not very dense. That means they need a screw with deep, aggressive threads that will bite into those soft fibers. Coarse-thread Kreg Pocket-Hole Screws work great for these woods.
What is a blue kote screw?from learn.kregtool.com
Blue-Kote™ Kreg Pocket-Hole Screwsare the best choice for damp or wet applications, including projects for your porch, patio, detached garage, or outdoor areas. These screws feature 3 anti-corrosion layers to help them resist corrosion in wet areas for the long haul.
What is pocket hole jig?from learn.kregtool.com
The pocket-hole screw is actually what holds your pieces together to create a strong, long-lasting joint.
The Correct Size Kreg Screw Length to Use
When choosing the correct length of pocket hole jig screw, you need to determine the thickness of the board you are joining with pocket holes.
How to Choose the Correct Kreg Screws
There are 3 main things to determine when choosing the correct length of Kreg pocket hole screws. They are: (1) whether it is an indoor or outdoor project, (2) the type of wood, and (3) the wood thickness.
Kreg Pocket Hole Jig Systems
Kreg Tool offers a lot of different options when it comes to pocket hole jigs that they sell. I used the K4 for years, but they don’t make it anymore. I have since upgraded to the 720Pro, which I highly recommend!
