What size thread is a radiator valve tail?
This radiator valve tail connects a radiator to a standard radiator valve. The male thread is 1/2 inch BSP (normal size for the connections on a radiator). The tail has a compression nut and olive to suit a valve with a 15mm compression type outlet. Click to see full answer.
What is a tail on a radiator?
Radiator valve tails are the devices that screw into the two bottom radiator tappings. They are connectors between the radiator and the valves that control the flow of water through the radiator. You might need to change a tail to fit a new type of valve. Click to see full answer.
What size are radiator fittings?
The tappings in a radiator are usually a standard 1/2 inch BSP female thread (see BSPT link at bottom of page for more info on plumbing thread sizes). Some radiator valves use a large union nut and tail, and others use a 15mm compression connection to the tail.
How big is a 650 isolating radiator tail?
Don’t forget your mobile number – Please ensure that your mobile number is added so that we can text you when your order is ready to collect. 650 Isolating Radiator Tails 15mm x 1/2" (Pair) is rated 4.8 out of 5 by 34 . Rated 5 out of 5 by Dave The Boger from Decorating Good quality!look good.
Do radiator tails come in different sizes?
RADIATOR VALVE TAILS VARIOUS DIFFERENT SIZES / COLOUR 1/2" 3/4" 1" CHROME B.
Are radiator tails universal?
The connection between your valve and the radiator is standard across all moderns radiators and valves. The size differences listed above refers to the width of your pipes that the valves will slot onto. Most of the time it's 15mm, but measuring your pipes will confirm.
How long is a radiator tail?
Plain 15mm part is 19mm long, total length of the tail is about 43mm.
What are the tails on a radiator?
Radiator valve tails are the devices that screw into the two bottom radiator tappings. They are connectors between the radiator and the valves that control the flow of water through the radiator. You might need to change a tail to fit a new type of valve.
What size are my radiator pipes?
The radiator circuits in most modern wet central heating systems are made from standard 15mm copper pipe, while the pipes that link the boiler, pump and points where the circuits split off will be 22mm or 28mm in diameter.
Are all radiator valve heads the same size?
15mm valves are the only size you're likely to encounter, since 15mm copper pipes are the most common. There are also other sizes, from 8mm to 28mm, and there are accompanying adapters.
How do you fit a radiator tail?
0:071:43How to fit a radiator valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd so I'm just going to show you simply how to install bit. So first off what we got do is put theMoreAnd so I'm just going to show you simply how to install bit. So first off what we got do is put the PTFE on the dark. And what the dark does that just holds the valve onto the red.
How do you replace a radiator tail?
0:030:59The Fast and Easy Way To Fit Radiator Tails - Power Tool DriveYouTubeStart of suggested clipEnd of suggested clipAnd we live in a standard hex shaft on the end of it it just fits into the end of a power tool. SoMoreAnd we live in a standard hex shaft on the end of it it just fits into the end of a power tool. So quite simply just fit into the panel. That would then fit over the top ERV.
How do you stop a radiator tail from leaking?
5:287:28Repair leaking radiator tail on radiator. - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou need to counter the valve with the Reverend. Now I'm gonna give this quite a bit of pressure nowMoreYou need to counter the valve with the Reverend. Now I'm gonna give this quite a bit of pressure now to make sure it's sealed.
Do radiator tails need PTFE?
Use jointing compound too If you are installing a new central heating component (like a radiator or a radiator valve) then it's advisable to use PTFE tape AND some silicone-based jointing compound, to make the joint completely watertight.
What size allen key fits radiator valves?
1/2 inchUse this 1/2 inch size allen key hex spanner to install or remove the tails of union type radiator valves that are screwed into a radiator. Made from high tensile steel, length approx 135mm. This IS NOT the tool you need to operate the air vent at the top of your radiator (we keep bleed keys for that in our store).
What saw would you use for cutting Rad tails?
The best rad tail saw to use for such an activity comes in the form of a jigsaw, which is the most versatile version available, offering a propensity to trim both curved and straight lines with equal accuracy and consistency.
terrymac Screwfix Select
If you want to keep the valves you have ,just remove the tails from the rad and fit them in the new rad ??
teabreak Screwfix Select
As above if the valves are good, a photo might help to advise if possible.
dvddvd Well-Known Member
thanks why would they put 2 sizes on each end of a radiator? The rest of the house is the same? will take a photo
teabreak Screwfix Select
One might be thermostatic or the control valve may have been changed for leakage or stiffness leaving the original lock shield ones in place. The picture will help.
dvddvd Well-Known Member
i was just wondering since the new radiator is 50mm shorter than the old one, i was going to use adjustable tails on the radiator. Is there a male coupling which is 3/4 to 1/2
dvddvd Well-Known Member
They are from when the house was built 40 years ago. Its microbore and all rads/valves are original and all have 1/2 on one side and 3/4 valve on other side ?
teabreak Screwfix Select
I doubt it my guess is one is a 15mm compression connection very common now and one is ground in union connection.
