What is the difference between a router and a wireless access point?
A router is actually a hub that you connect your devices to and is responsible for handling and managing your network. A wireless access point, on the other hand, is a wireless point you connect your devices to which then further connects you to the main network.
How can I ensure that the two wireless networks do not overlap?
The wireless networks do not overlap. Both of them use Wi-Fi Protected Access (WPA). You want to ensure that no unauthorized wireless access points are established. What should you do? A Change the two wireless networks to WPA2. B Change the two wireless networks to WEP. C Periodically complete a site survey.
What is the IP address of the wireless access point?
The IP address of the wireless access point is the IP address that is listed for Default Gateway. It’s worth noting that the default gateway is actually just the IP address for the router that connects to the Internet. In certain networks with more than one router, this might be the IP address of your ISP router,...
Which device is used to transmit data between networks between networks?
A router is a device that is designed to transmit data between networks on a TCP/IP internetwork. Bridges, hubs and routers are not used to create DMZs." "Which type of firewall is also referred to as an appliance firewall? A hardware firewall is also referred to as an appliance firewall.
What is another name for a wireless access point?
hotspotA WAP is also known as a hotspot.
What term refers to using an open wireless network without permission?
piggybacking: Using an open wireless network to access the Internet without permission.
What is a wireless access point in simple terms?
A wireless access point (WAP) is a networking device that allows wireless-capable devices to connect to a wired network. It is simpler and easier to install WAPs to connect all the computers or devices in your network than to use wires and cables.
What is an Internet access point called?
In computer networking, a wireless access point (WAP), or more generally just access point (AP), is a networking hardware device that allows other Wi-Fi devices to connect to a wired network.
When devices connect through a wireless access point they form an infrastructure wireless network True or false?
When devices connect through a wireless access point, they form an infrastructure wireless network. A router is a device that connects two or more networks together. You must install special software to create a peer-to-peer network. TCP/IP is the default protocol installed on Linux computers.
How do you recognize an unsecured wireless network?
How can you recognize an unsecured wireless network? The network icon will have a warning symbol. How would you set up your connection so that it connects to a particular wireless network every time you're in the area without requesting any manual intervention?
What are the types of access points?
Based on functionality an access point can be categorized in three types; standalone, multifunction and client. A standalone access point works in the wireless network exactly as the switch works in the wired network. To control the unauthorized access, Access point uses authorization.
What is an access point quizlet?
What is an access point (AP)? the computer or network device that serves as an interface between devices and the network.
What is an access point example?
An access point is a device, such as a wireless router, that allows wireless devices to connect to a network. Most access points have built-in routers, while others must be connected to a router in order to provide network access.
What is the term that defines the access point for the service provider's services?
A Service Access Point (SAP) is an identifying label for network endpoints used in Open Systems Interconnection (OSI) networking. The SAP is a conceptual location at which one OSI layer can request the services of another OSI layer. As an example, PD-SAP or PLME-SAP in IEEE 802.15.
What are areas around access points where users can connect to the Internet via Wi-Fi?
A wireless access point covers an area with a WiFi signal, and the area in which one can connect to the Internet over the air is called hotspot.
What is access point in security?
Advertisements. Access Point (AP) is the central node in 802.11 wireless implementations. It is the interface between wired and wireless network, that all the wireless clients associate to and exchange data with.
What is the purpose of a DMZ?
The main benefit of a DMZ is to provide an internal network with an advanced security layer by restricting access to sensitive data and servers. A DMZ enables website visitors to obtain certain services while providing a buffer between them and the organization's private network.
What type of network does not require a network operating system?
Peer-to-peer network (P2P) A network that does not require a network operating system, in which each computer is considered equal; each device can share its resources with every other device, and there is no centralized authority.
Which of the following is used on a wireless network to identify the network name?
Which of the following is used on a wireless network to identify the network name? Wireless devices use the SSID (Service Set Identification) to identify the network name. All devices on a wireless network use the same SSID.
Which type of network creates a private network through the public network?
VPNs, or virtual private networks, create a private network through the public network, the Internet, allowing remote users to access a LAN securely without needing dedicated lines.
What is a bridge in a network?
A bridge is a device that separates a network into distinct collision domains to control network traffic. A network divided by a bridge is considered to be a single network. A hub is a central connection device used on Ethernet networks. A router is a device that is designed to transmit data between networks on a TCP/IP internetwork. Bridges, hubs and routers are not used to create DMZs."
What is a network divided by a bridge?
A network divided by a bridge is considered to be a single network. A hub is a central connection device used on Ethernet networks. A router is a device that is designed to transmit data between networks on a TCP/IP internetwork. Bridges, hubs and routers are not used to create DMZs.".
How does IPSEC work?
IPSec can work in either tunnel mode or transport mode. IPSec uses Encapsulation Security Payload (ESP) and Authentication Header (AH) as security protocols for encapsulation. The IPSec framework is used in a virtual private network (VPN) implementation to secure transmissions.
Why do individual hosts not need real time monitoring?
Individual hosts do not need real-time monitoring because intrusion is monitored on the network segment on which the NIDS is placed, and not on individual workstations.
Why is an application-level proxy firewall most detrimental to network performance?
An application-level proxy firewall is most detrimental to network performance because it requires more processing per packet.
What is hardware firewall?
Explanation: A hardware firewall is also referred to as an appliance firewall. Appliance firewalls are often designed as stand-alone black box solutions that can be plugged in to a network and operated with minimal configuration and maintenance.
Why are host-based intrusion detection systems (HIDSs) so difficult to configure and monitor?
By contrast, host-based intrusion detection systems (HIDSs) are difficult to configure and monitor because the intrusion detection agent should be installed on each individual workstation of a given network segment. HIDSs are configured to use the operating system audit logs and system logs, while NIDSs actually examine the network packets.
What is wireless media?
Wireless media are also referred to as unbounded network media, where data signals are transmitted. through the air instead of cables. Wireless communication permits connections between areas where. it would be difficult or impossible to connect using wires, such as in hazardous areas, across long.
What is 802.11 standard?
802.11. standard is a family of specifications developed by the Institute of Electrical and. Electronics Engineers (IEEE) for the wireless LAN technology. 802.11 specifies an over-the-air. interface between a wireless client and a base station or between two wireless clients. 802.11 defines.
What frequency is radio?
waves in the 10 KHz to 1 GHz range. Radio networking is subject to electrical interference from
What is broadcast radio?
Broadcast radio. is a form of RF networking that is non-directional, uses a single frequency for. transmission, and comes in low- and high-power versions. Low-power RF transmissions travel a. short distance, often no more than 70 meters, but are inexpensive and relatively easy to install. High-.
What is antenna pathway?
antenna pathways to send additional data. It can also recombine signals it receives to increase
How many antennas does an 802.11ac router have?
than previous wireless standards. 802.11ac routers can also have up to eight antennas.
How many endpoints does a connection have?
connection has more than two endpoints. A signal transmitted by any device through a medium
Why do we need wireless access points?
Wireless access points are usually used to extend the range of the main network so more people can join the network . A router can have multiple wireless access points enabled on it for various purposes, and users can connect to them.
What app to use to find access points?
If you need to find these access points, you’re going to need to use a network scanner app . NetSpot (freemium) is one of the apps that lets you scan for both hidden and non-hidden networks around you. Using it is pretty easy as all you need to do is install and run it.
How to find my IP address on my wireless network?
If you’re already connected to the network via WiFi or Ethernet, you can head into your adapter settings menu to find out your wireless access point IP address. Right-click on the network icon in the system tray and select Open Network & Internet settings. On the following screen, click on the option that says Change adapter options.
What is the difference between a WAP and a router?
They’re actually two different things and so they work in a bit different way. A router is actually a hub that you connect your devices to and is responsible for handling and managing your network.
What is the Mac terminal?
The Mac Terminal has a number of commands you can use to execute various tasks and one of these lets you view your network information. You can utilize it to find the IP address of your wireless access point.
Can I find my wireless access point IP address on my Mac?
Your wireless access point IP can be revealed on your Mac machine as well. If you go for the GUI method, all you basically need to do is click on a few options and you’ll have access to the required IP address of your WAP.
Does each device have its own IP address?
This includes your wireless access point as well and it has its own IP address assigned to it. Sometimes, you may need to access this IP to do certain things like changing your network configuration, setting up a new WiFi password, and so on.
What is an active/active network?
Active/Active is where all nodes process simultaneously. In the case of failover, perfomance is reduced but service is maintained.
What is wireless engineer?
A wireless engineer implements a new Wi-Fi network organization. The engineer carefully planned the deployment of access points (APs) to maintain a configuration spacing of 25 MHz. Consider the given wireless network symptoms and determine which relates to the configured value.
What is privileged user?
A privileged user utilizes network resources to perform the job function. The administrator of a small bust fast-growing company sets out to develop a privileged user agreement (PUA) to ensure correct classification of network resources and information assets and that the correct staff member handles them.
Can a misconfigured firewall be accessed via a web interface?
A misconfigured firewall is not accessible via traditional web-based interface. To gain access, and engineer needs to use a serial cable directly connected to the firewall by using a com port on a PC. Which of the following is the connector type the engineert will need to connect to the PC?
Can a recently booted computer access network resources?
Recently booted computer systems at a large company are not able to access any network resources. IT investigates and finds the systems configured with automatic private IP addressing (APIPA) addresses. Consider the given choices and then determine which could cause the issue.
What is the MAC address of 802.11a?
An 802.11a compatible client can connect to the wireless network only if its MAC address is 00- ab-29-da-c3-40 and the encryption key is known by the client. C. An 802.11n compatible client can connect to the wireless network only if its MAC address is 00- ab-29-da-c3-40 and the encryption key is known by the client.
How many computers are on a remote site?
The remote site consists of ten desktop computers, ten VoIP phones, and two network printers. In addition, two of the desktop computers at the remote site will be used by managers who should be on a separate network from the other eight computers.
What is a 575 call?
575. A network technician receives a call from a branch office about a problem with its wireless connectivity. The user states the office is hosting a large meeting that includes some online training with local businesses. The guest users have all brought devices to connect to the guest network at the branch office.
What are the businesses inside an airport terminal called?
Businesses inside the airport terminal are known as concessions. These usually sell food, drinks or retail goods such as magazines, books, or souvenirs to passengers.
What is an airport kiosk?
Kiosk. An airport kiosk is an interactive, computerized device where people can get information or services. These are usually located throughout an airport terminal for easy access. A kiosk may be consulted about flight status, flight schedules or other inquiries.
What is baggage area?
The baggage area is the area of the airport that handles baggage carried by passengers. These often have several large moving belts. Passengers wait at the belt for their baggage to move to them.
What does it mean when a plane is in range?
If you hear them announcing that your flight is now "in range" that means that the plane is in the process of landing, but hasn’t touched ground yet. This announcement is to give you a heads up to get ready to board the plane, though how long it will take for the plane to actually land and be ready for passengers is never an exact science.
What is ramp in airport?
Typically, a ramp is an inclined plane that allows transit between two areas that have different levels. In an airport, this word refers to a staircase with wheels, which is used to load or unload an airplane. The word is also used in sea travel, referring to an inclined walkway installed between the vessel and the port.
What does "direct flight" mean?
Direct flight simply means that the flight number will not change, but in many cases your flight will indeed stop. You may even need to change planes completely.
What is the definition of airspace?
The space over the land or sea area occupied by a certain state or country. A country's airspace is considered part of that country's territory and therefore subject to its authority.
