Types of Ball Joint Grease
- Multi-Vehicle. When automakers design cars, it's their job to figure out exactly which lubricants should be used. ...
- Multipurpose. Multipurpose grease is exactly what the name implies. ...
- Marine. Marine grease is a blend specifically designed to deal with exposure to water. ...
- Moly Reinforced. ...
How to grease ball joints properly?
- Prepare your work area: Make sure you have everything you need to grease your car. ...
- Locate the joint you’ll be greasing: You’ll need to locate all of your car’s ball joints, rear-end joints, and suspension joints. ...
- rep the joint: Prep the joint with spray cleaner and wait for a few minutes if needed. ...
How do you add grease to sealed ball joints?
Sealed Ball Joint Greasing?
- Will puncturing the OE boot on 2nd Gen sealed Ball Joint's cause any issues, other than the obvious it might tear?
- Has anyone done this?
- Maybe can get into the void of the boot by slipping the needle under the boot rather than through it?
How to grease a ball joint without fitting?
What grease is best for ball joints?
- Best Grease for Water Resistance: Sta-Lube SL3121.
- Best Grease for Temperature Stability: Triax RED SPHERON HT-2.
- Best Grease for Load/Pressure Resistance: Lucas Oil 100005 Red ‘N’ Tacky.
- Best Grease for Longevity: Lucas Oil 10005 Red ‘N’ Tack.
Do ball joints need grease?
Why Do Ball Joints Need Grease? Grease provides smooth action for ball joints to operate efficiently and protect against wear. Packaging of ball joints, depending on vehicle design, may place it close to hot engine components where it needs to resist breakdown due to heat.
Can you use any grease for ball joints?
The best ball joint grease for your vehicle and environment will depend on a few factors but basically any grease rated "GC-LB" by the NLGI (National Lubricating Grease Institute) is graded to work for ball joints.
What kind of grease do you use on joints?
The best type of grease to use on U-Joints is MOLY grease. This grease is certified for this purpose. You can also use lithium-based EP NLGI 2 Grease, which is of high quality. This grease is also water-resistant and prevents the joints from corrosion and rust.
Is silicone grease good for ball joints?
Nye's Fluorocarbon Gel 880 is a PTFE-thickened, heavy viscosity dimethyl silicone grease with excellent water resistance and structural stability under a wide temperature range and is our recommended solution for most ball joint applications.
Which grease is best?
These are the three best greases from the current market for your vehicleBest Overall. Valvoline SynPower Synthetic Automotive Grease. Check Latest Price. Summary. ... Best Value. Lucas Oil 10301 Heavy Duty Grease. Check Latest Price. Summary. ... Honorable Mention. Maxima 80916 Waterproof Grease. Check Latest Price. Summary.
How much grease do you put in ball joints?
0:031:53How-To Grease Ball Joints, Tie Rods, and Other Suspension Components.YouTubeStart of suggested clipEnd of suggested clipThere it is the bottom side of the ball joint and once you start to see grease squeezing out like itMoreThere it is the bottom side of the ball joint and once you start to see grease squeezing out like it is right there that means you've got plenty of grease in your joint.
Is Green Grease good for ball joints?
Green Grease is used extensively for automobile and motorcycle applications. Where you see it used effectively is: U-joints, chassis lube, CV joints, upper and lower A-arms, ball joints, tie rod ends, polyurethane bushings, disc brakes, steering linkages and wheel bearings.
What is white lithium grease good for?
White lithium grease is used to keep components moving smoothly, free of friction and seizing. You can also apply it preventatively to protect against rust and corrosion. White lithium grease can be used to: Lubricate car door hinges.
What is joint grease?
Joint grease for recorders is used to keep cork joints and O rings lubricated to ensure easy assembly. This canister is specially made to fit inside the case of most recorders. This is a package of 6 joint grease canisters.
What is special about CV joint grease?
CV Joint Grease has excellent water washout resistance where in these applications, provides outstanding protection against rust and corrosion. It is also extremely shear stable for both high and low temperatures and provides protection for intermittent operation up to 200°C.
What kind of grease for tie rod ends?
Grease – You should use the OEM suggested grease or a Heavy Duty Lithium Synthetic or Marine grease. These are perfect for automotive applications and will last longer than other types.
How do you grease a drive shaft U-joint?
0:472:13How to Lube a New U Joint - YouTubeYouTubeStart of suggested clipEnd of suggested clipHowever what you're going to want to do is use your grease gun and fill it up until you see greaseMoreHowever what you're going to want to do is use your grease gun and fill it up until you see grease spooning out from the u-joint seals i'm going to go ahead and pop that on right now.
Can you lubricate ball joints?
If the ball joint is capable of being greased, use only the grease that is recommended for the job. Some ball joints come lubricated for life and are therefore incapable of being greased – the paradox though is that they don’t usually live very long.
Is red grease good for ball joints?
Color has no bearing on grease performance EXCEPT for one area: never use a black grease in a non friction bearing/wheel bearing/universal joint. Period.. Use yellow, purple, pink, red, whatever, just no moly. Moly will give a steel grey appearance to a grease.
What type of grease does Moog use?
MOOG engineers suggest using a premium heavy-duty lithium or synthetic grease.
Should I grease new ball joints?
Ball joints allow you to steer smoothly and are constantly moving so throwing a little lubrication their way is a small favor for the big job that they do every day. The rule of thumb is to grease these parts every, or every other, oil change which might seem excessive, but again; little thanks, big job.
How do you grease a ball joint without grease fitting?
Instruction to Grease a Ball Joint Without Fitting Check the Boot. At first, get the tire off. Prepare the Grease Gun. Inject Your Needle into the Boot. Start Pumping with the Grease Gun. Eject the Needle. Driving Test.
What is the difference between regular grease and lithium grease?
The most important difference between these two types of grease is that calcium-sulfonate greases do not typically need additives to meet certain performance requirements like lithium-complex greases do. Calcium-sulfonate greases are also compatible with lithium and lithium-complex greases.
Is Lucas red and tacky good for wheel bearings?
It appears you really can’t go wrong with either one for wheel bearings. I’ve had good results with Red, so I just stick to what I know works for me. Red seems to be recommended more for wheel bearings, green for more heavy duty applications where you won’t be inspecting or re-greasing often.
What is a grease gun?
A Grease Gun – We suggest a manually powered grease gun that will put you in direct control of how much grease goes in and allow you to “feel” any resistance that the ball joint might be giving while you grease it.
What is a grease zerk needle?
A grease zerk needle adapter – This needle is fitted with a grease zerk and will attach to your grease gun.#N#* Take care when attaching the needle, since some force is required you could easily skewer your hand. Most needle attachments come with a plastic sheathe, so leave that on until the zerk is attached to the grease gun.
What to use to clean zerks on car?
The grease zerks on many vehicle’s ball joints are almost impossible to connect to directly, even with a mini grease gun. Save the frustration and use a hose. Rag – To clean the zerk and wipe excess grease away.
What is the best way to cover a needle hole in a dust boot?
Weather stripping adhesive can be used to cover the needle hole in the dust boot if you’re worried that water or contaminates might make their way through to the smooth working surface of the ball joint. This adhesive forms a flexible, water-proof seal that is resistant to the elements.
Do aftermarket ball joints have zerks?
Most aftermarket ball joints have grease zerk fittings which make the lubrication process a lot easier, but some folks want to add a little grease to the sealed, stock ball joints on their vehicles that do not have zerks. This how-to will lay out detailed instructions for greasing sealed ball joints and those that have zerk fittings.
Can you grease a ball joint with a zerk?
You can use a grease zerk needle attachment to get past the dust boot and pump some grease into that ball joint. This can eliminate those noises and potentially extend the life of the part, but this method will almost certainly not grease the entire part.
Do ball joints need grease?
Most manufactureres use sealed ball joints that do not come with grease zerk fittings. Theoretically, these ball joints will not need any extra grease and are sealed up tight so contaminates can’t get inside, but if you notice a groaning while turning then the culprit might be a grease-thirsty ball joint.
