Where are the fuses located on a prelit Christmas tree?
0:201:14Christmas lights hidden fuse indoor/outdoor lights. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo with this unplugged you don't want to do this plugged in or you will get electrocuted unplug itMoreSo with this unplugged you don't want to do this plugged in or you will get electrocuted unplug it this right here slides open. So you can use a screwdriver your fingernail. Anyway slide that out.
Do pre lit Christmas trees have fuses?
Most prelit trees have fuses inside the electrical plugs. Double-check that the tree is unplugged from the wall and then check each plug and connector for a blown fuse. Unplug the cord from the wall. Open the fuse cover on top of the plug by sliding the cover toward the blades or prongs.
How do you change a fuse on a pre lit Christmas tree?
0:020:37How to Replace The Fuses on Your Christmas Tree - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse your finger or a flathead screwdriver to. Slide open the small compartment on the plug. The fuseMoreUse your finger or a flathead screwdriver to. Slide open the small compartment on the plug. The fuse should pop out with a small amount of force.
How do you fix a prelit tree that won't light?
This often occurs through rough handling or improper storage of a tree. Look to find the loose bulb, check the wires to ensure they are properly aligned, and secure the bulb tightly within the socket. This should fix the issue. If a short has occurred, the light string is usually not repairable.
How do I know if my Christmas tree fuse is blown?
The fuse is a small, glass cylinder with metal-plated ends and an internal metal filament. You can sometimes tell by sight if a fuse has blown; the metal filament inside the glass cylinder will have a break in it.
How do you troubleshoot a prelit Christmas tree?
General Troubleshooting Tips: Pre-lit TreesTry stepping on the ON/OFF foot pedal.If the tree is plugged into a switch controlled wall outlet, make sure the switch is turned ON.Be sure you have plugged all the sections together. ... Check for loose or burned out bulbs.More items...
How do you tell which light is out on a Christmas tree?
You can tell which bulb is out on your string of traditional Christmas lights by looking for the bulb that is “burned out” by looking at the tiny little filaments in the light bulbs to see which bulb is “burned out” or has lost it's filament. Many times the bulb will be “smoked” as well.
Do all Christmas lights have a fuse?
Short answer: Yes, most Christmas lights have fuses in the male plug end. If the entire string of Christmas lights has gone out, this is the first thing to check for troubleshooting.
How many fuses are in Christmas lights?
Most string lights have two tiny fuses inside the plug. Typically, a box of lights is also packaged with a replacement fuse or two. To replace a fuse, take a small set of pliers or flathead screwdriver and slide open the cover.
How do you fix LED lights on a pre-lit tree?
0:053:33How to Troubleshoot and Repair Christmas lights on a Pre lit Life like ...YouTubeStart of suggested clipEnd of suggested clipMost likely is a light set that is not working an entire set of 50 bulbs. And that's where you'reMoreMost likely is a light set that is not working an entire set of 50 bulbs. And that's where you're going to use light keeper Pro to fix that light set.
Can you remove lights from a pre-lit Christmas tree?
Step 1: Cut Wire Near Base or Trunk You don't have to worry about taking the cords off in one piece. You are never going to use these lights again! Cut away! Be sure to cut close to the base or trunk of the tree and then cut each wire that has a light.
What causes a whole string of lights to burn out?
The reason for this has to do with the nature of electrical circuits and the Christmas bulbs that depend on them. If a string of Christmas lights has a single wire connection, it can cause the entire string to go out when one bulb goes bad.
How do you change a fuse in a string of lights?
0:100:37How to Replace Fuses in Christmas String Lights - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst unplug the lights and open the fuse door located on the male end of the plug pop the fuses outMoreFirst unplug the lights and open the fuse door located on the male end of the plug pop the fuses out using a small screwdriver if necessary note the dimensions of the fuses.
How do you test Christmas tree lights?
Checking Faulty Christmas Tree LightsPlug the lights into an electrical outlet.Turn the light switch and the circuit breaker on.Check the fuse or fuses from the plug at the end of the light strand (usually the glass-cylinder type with a wire filament). ... If the fuse isn't the problem, there's a problem with a bulb.More items...
Introduction
In this guide, you will learn how to replace the fuse on a pre-lit incandescent (non-LED) Christmas tree. Incandescent lights are electric lights that have wire filaments that are heated until they glow. The filament is enclosed in a glass bulb that protects the filament from oxidation.
Step 3
Open the fuse cover, then use a small flathead screwdriver or spudger to carefully remove the fuse.
Step 4
Using a continuity tester and the fuse, place both tips of the continuity tester on either side of the fuse.
Step 5
Carefully insert the working fuse back into the tree plug, and put the cover on.
Step 7
Using the Christmas light function tester, go back to the same spot you initially checked. If the red light appears, you have successfully replaced the fuse!
FULL TREE
If the full tree does not light, make sure it is plugged into the wall. If the tree has a footswitch, step on it.
SECTION
If a section does not light, ensure that unlit strand (s) or section (s) are fully plugged into other strands and/or extension cords.
STRAND
If the issue is with individual strand (s), visually check for broken and discolored bulbs and replace as needed.
How to troubleshoot a prelit Christmas tree?
Most troubleshooting in trees centers around light strings that have gone dark, or the initial assembly of the new tree. Methods in troubleshooting include testing the light strings in an effort to find the faulty bulb, or simply replacing the existing light strings with working sets. Below you will find the most common problems and solutions associated with light strings on prelit Christmas trees.
What to do if fuses are not working?
If the fuses all look fine or replacing them does not fix the problem, there may be a problem with a bulb or the wiring itself. Replace any damaged bulbs with spare ones. If the issue is with the wire itself, remove the entire string and replace with a new strand of lights .
How to fix a plug that is burnt out?
Check the plug fuses. Slide open the door of the plug and replace any fuses that look burnt out . Then plug the strand into an extension cord to see if this fixes the problem. Need help? Watch this video on replacing fuses!
What happens if a mini light bulb is pulled out of socket?
If one of the wires is misaligned, or if a bulb is pulled out from its socket, the current is broken and the light strand will go out.
How many plugs does a tree need?
Many times the main plug that goes to the outlet is not in the lowest section of the tree, which can seem confusing. Larger trees often have 2 or 3 plug s that go into the wall, so look for these if the tree does not light completely. Each of these plugs will also have a fuse, so check to make sure they do not need to be replaced if a section of the tree is not lighting.
Why is my tree not turning on?
If the tree has multiple light plugs stacked together, the most common reason for a section not turning on or flickering is often as simple as one of these plugs coming loose. Check that all plugs are secure. If your tree is a power pole or one plug design, check each section where the poles meet to ensure that there is nothing obstructing the connection and that they are seated properly .
Why do lights go on and off in a tree?
If lights go on and off as the tree and branches are moved around, this is not always an indication that there is a short in the wire. Most likely a bulb is loose, and the connection is getting lost as the bulb moves in its socket. This often occurs through rough handling or improper storage of a tree. Look to find the loose bulb, check the wires to ensure they are properly aligned, and secure the bulb tightly within the socket. This should fix the issue.
