The seemingly constant water flow through your yard's sprinkler system mainly is due to the sprinkler pump. Typically located between your water source and the sprinkler valves, the pump moves water at a steady rate so that each spray head receives enough water for irrigation.
Where are sprinkler valves installed?
Some sprinkler valves are installed above ground and thus are easier to locate. These types of sprinkler valves are usually installed near the water source, so the best place to start is by looking around the perimeter of the house.
Can you put a sprinkler pump above the water source?
Because sprinkler pumps aren't designed for suction head over 25 feet, you want to install them as close to the water source as possible. Irrigation pumps aren't capable of sucking water beyond 25 feet above their water source. If you have to locate your pump higher above the water source, consider a different type of pump.
Where is the best location to install an irrigation pump?
It's much easier for a pump to push water out than it is for it to pull water upward, so it's best to install your irrigation pump as close to the water source as possible without risking water-damage to the pump.
How to install a sprinkler system in your yard?
Find the sprinkler controller to serve as the starting point for the path of the wires for the sprinkler valves. Sometimes tracing the path of the wires can lead to the sprinkler valves. You may need to dig up some of the yard to follow the sprinkler wires. Take care not to damage the wires when digging.
Do all sprinkler systems have a pump?
Water pump Water pumps are the heart of the irrigation system. For smaller systems, you may have a single booster pump. However, most can count on the need for a multiple irrigation pumps depending on their design.
What does a sprinkler pump look like?
0:395:29Landscape Irrigation Pump Overview - YouTubeYouTubeStart of suggested clipEnd of suggested clipOr the well or the storage tank. The water is boosted by the impeller. And it comes out theMoreOr the well or the storage tank. The water is boosted by the impeller. And it comes out the discharge side and on to the lawn sprinkler system so you can operate properly.
Where is my sprinkler system controller?
Often these are easily visible. In small yards, there is often a single valve box located near where the irrigation pipes enter the ground from the water source. Larger yards may have remote valve boxes set at the start of each irrigation zone.
How do I turn on my irrigation pump?
0:392:08How To Turn On An Irrigation System (Dedicated Irrigation Well) - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will want to make sure that the power to the well is turned on or the breaker is flipped to theMoreYou will want to make sure that the power to the well is turned on or the breaker is flipped to the on. Position. The next step will be to turn the irrigation controller.
What is sprinkler pump?
The fire sprinkler pump distributes the water via the pipe-system and discharged by the sprinklers. Fire sprinkler systems use water to suppress and in best case to extinguish fires in buildings. Piped systems are used to distribute the water throughout the building to where the fire is present.
How do I know if my water pump is pumping?
6:2610:50HOW TO CHECK IF YOUR WATER PUMP WORKS & CIRCULATES ...YouTubeStart of suggested clipEnd of suggested clipSometimes you can tell if the water is flowing if you just look down there all right sometimes youMoreSometimes you can tell if the water is flowing if you just look down there all right sometimes you can see the water flow and that'll let you know if your water pump is slowing.
How do I find my sprinkler valve box?
1) Start in the Most Likely PlacesProbe the soil. Determine the irrigation valve area, and sift through the soil in that specific section of your property. ... Look for valves box covers. If valve boxes were set over the valves when the system was installed, they are most probably just under the surface.
How do I find my sprinkler master valve?
0:091:37How to Locate your Water Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe customer service valve to the meter service is located in a round box just after the meter boxMoreThe customer service valve to the meter service is located in a round box just after the meter box fronting your property.
Where is my irrigation box?
In most cases, your sprinkler valve box will house your manifold and valves. Occasionally valves will be above ground. Valve boxes are generally around the permitter of your house - so when searching for your valves, start there!
Why is my sprinkler pump not turning on?
If it isn't turned on or if it's tripped, you may just need to reset it. If you reset a tripped breaker, and it continues to trip you may have an issue with the wires running to the pump or the pump motor itself — or some other issue that's causing your pump to get too little electricity – or too much.
How do I turn off my sprinkler pump?
0:001:00How To Turn A Sprinkler System Off in 3 Simple Ways - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition. Off position that's number one number two look for your double. Check get a little blueMorePosition. Off position that's number one number two look for your double. Check get a little blue handle right there there. All you have to do is turn off one of them.
How do I turn on my sprinkler system in the summer?
1:598:55Turning On House Sprinklers for Summer Season - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe pipe leading to the outside is over there. Down this is the valve we want to turn on so iMoreThe pipe leading to the outside is over there. Down this is the valve we want to turn on so i usually turn it on slowly to let the water fill up that pipe out to the spigot that we've turned.
Why does my sprinkler system keep flowing?
The seemingly constant water flow through your yard's sprinkler system mainly is due to the sprinkler pump. Typically located between your water source and the sprinkler valves, the pump moves water at a steady rate so that each spray head receives enough water for irrigation.
What are the problems with a sprinkler pump?
Available in various design choices, your sprinkler pump may experience problems over time that require basic troubleshooting skills. Loose electrical wires and leaking pipes tend to be the most common problems that you may repair on your own.
How to work out the size of a sprinkler pump?
To work out the required pump size, multiply your GPH/GPM by the number of sprinkler heads. For example, if you have 10 heads each at 5GPH, your sprinkler pump should deliver 50GPH. As the PSI remains constant and should be the same for all your sprinkler heads, your pump should simply match that requirement.
Where are Wayne sprinkler pumps made?
What's more, all Wayne sprinkler pumps are built and constructed in the USA, guaranteeing the highest level of quality and wide availability of replacement parts, should you need them. Wayne recommends keeping your sprinkler pump sheltered at all times to prevent rust and weathering.
What voltage do sprinkler pumps work?
Most sprinkler pumps are rated for both 230v and 115v, so depending on your power supply can be tailored to meet your situation.
What is the force of water exiting a sprinkler pump?
This simply refers to the force of the water exiting the sprinkler pump and sprinkler heads. It's a key factor in determining how much area each sprinkler can cover. The higher the pressure, the further distance your water will be expelled from the sprinkler head.
How long is a sprinkler pump warranty?
Most sprinkler pumps come with a 1-year limited warranty as a minimum, with some brands offering up to 3. Generally, you should expect to pay a little more for units with extended warranties.
What is irrigation pump?
A pump that uses a rotary motion with an impeller to create flow. These are the most popular type of irrigation pumps on the market, and widely available for purchase.
How far can you run a sprinkler head?
As a rule of thumb, if your distance from the pump to the last sprinkler head in your irrigation system is less than 100 feet, you can manage with the standard 1-1/2" discharge pipe, which should be enough to cover most homeowners.
What is a sprinkler system diagram?
Many sprinkler system installers provide a system diagram that outlines the location of sprinkler heads and valve. If the irrigation system required a permit for installation, your local permits department may still have an irrigation blueprint on file, which will indicate the location of the valves. It may be possible to follow the sound of the ...
How to find buried irrigation valves?
Often you can estimate the rough location of the irrigation valve, then find a buried valve box by probing the ground.
What is irrigation repair?
natbits / Getty Images. In a lawn irrigation system, repair or replacement of an irrigation valve is a very common repair. An irrigation system is typically divided into several zones, each of which feeds sprinkler heads in a different area of the lawn or garden, and each zone is controlled by a valve that receives signals from a centrally located ...
Where are valves located?
In this case, it's usually quite easy to find the valves. Often the valves are located inside one or more in-ground valve boxes. The tops of these boxes will be at ground level, and these, too, are usually fairly easy to spot and access. The valve box, or sometimes the valves themselves, are sometimes buried underground.
Where are below ground valves located?
Here are some tips for location below-ground valves, beginning with the easiest. Begin by looking for exposed valve boxes. In many instances, the valves will be conveniently located in green or black plastic boxes set into the ground, with covers that can be removed to expose the valves. These boxes have covers that can be removed to access ...
Where is the valve box located in a house?
Very often, the valve location is near the corners of the house or just slightly past the backflow preventer. Probe the ground to a depth of about 6 to 12 inches and listen/feel for the presence of the hollow valve box.
Can you find the sprinkler valves?
Surprisingly often, though, it can be difficult to locate the sprinkler valves. The task is complicated by the fact that the valve locations can vary greatly depending on the size of the yard and the design of the system.
What is a pump in a sprinkler system?
Every time you turn on your sprinkler system and the heads pop up to water your lawn, a pump is responsible for providing them with a steady water supply needed to maintain your lawn green and landscaping watered.
What is a sprinkler pump?
Lawn sprinkler pumps are centrifugal, which means they use an impeller to draw water in through a larger pipe and push it out through a smaller one. If air or gas accumulates in the impeller’s eye as a result of the pump casing having lost its prime, you run the risk of burning out your pump motor and causing major damage to your entire system.
What does priming a sprinkler pump mean?
Priming a sprinkler pump simply means filling up the pump casing and suction piping with water, turning on the pump switch, and ensuring there is no air in the inlet line. Please note that even self-priming pumps require at least the pump casings filled with water before they can start operating.
What is cavitation in sprinkler system?
Depending on the pumped water quality and duration of cavitation, the damage it causes to the sprinkler pump ranges from minor pitting to complete failure. Cavitation can also be caused by having an elbow ...
Why is my sprinkler pump not moving water?
If your sprinkler pump is on and moves water, but not enough to cover the entire lawn and landscaping, one possible cause is the suction pipe above the water line is not airtight, and the pump is sucking air through small cracks around the joints.
What happens when a water pump stops working?
When the pump no longer performs properly, water flow is significantly reduced, and it may not reach the entire area requiring irrigation. Some irrigation problems are easy enough to fix yourself if you have a fundamental understanding of how each component of your system operates, while others may require the assistance of a professional.
What happens if you reset a pump breaker?
If you reset the breaker and the problem is still not fixed, you may have an issue with the wiring running to the pump, such as loose wires and connections, or the motor may have shorted out. Check the voltage at the pump motor and pressure switch to identify which, if any, wires are loose and need to be fixed.
