Reasons why the chainsaw chain keeps coming off
- Worn-out drive sprocket If your chainsaw chain jumps off the bar many times, the likely perpetrator might be the wear and tear of the drive socket. ...
- Chain not properly set Another reason why your chainsaw chain jumps off the bar is that it wasn’t correctly set. ...
- Worn-out bar heel ...
- Fluctuating temperature ...
- Fatigued bar rails ...
- Impaired guide bar or chain ...
- Mechanical issues ...
- The chain isn’t loose ...
Why doesnt your chainsaw oil the chain?
The most common reason a chainsaw oiler stops working is that the oil hole gets clogged. To fix this, remove the chain and bar from your chainsaw and clean the oil hole and oil outlet port. If this doesn’t fix the problem, you’ll probably need to replace the oil line or pump.
How to replace the chain on a chainsaw?
Steps On How To Replace A Chainsaw Chain
- Disengage The Chain Brake Of The Chainsaw. In some chainsaws, the chain brake is attached to the side plate. ...
- Detaching The Side Plate Of The Chainsaw. To remove the chainsaw we need to remove the side plate to access the chain. ...
- Release The Chainsaw’s Tension. ...
- Detaching The Chainsaw’s Chain. ...
- Adjust The Tensioning Screw. ...
What is the best chainsaw ripping chain?
The sequence of Granberg ripping chain is compromised of two scoring cutters and two clearing cutters. The good folks at Granberg make the best ripping chains on the market and they can make you a custom chain to fit any size chainsaw setup you’re running.
Why did my chainsaw chain break?
Why did my chainsaw chain break? Below are some factors that can lead to a chainsaw chain break while in use. Not Maintaining your Chainsaw Regularly. Low-Quality Chain. Chain Rust. No maintenance of Guide Bar. Lack of Lubrication. Incorrect Chain Tension. Low oil levels in the oil chamber.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don't over-tighten the chain as this could cause it to break.
How tight should the chain be on a chainsaw?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can't pull the drive links out of the bar nose.
Why won't my chainsaw chain tighten?
Turn the tension control screw to the right to tighten the chain and to the left to loosen it, instructs eReplacementParts.com. Attempting to turn the tension screw without loosening the nuts first may be the reason you can't tighten the chain. Tighten the nuts back into place when you have the chain properly adjusted.
When should you throw away a chainsaw chain?
Chainsaw feels unbalanced, cuts unevenly, or rattles when in use. In short, if you have attempted to balance your cutting teeth, are certain of your depth gauge, and the tension is properly adjusted, but the saw still doesn't cut correctly- then you need to replace the chain.
How many times can you sharpen a chainsaw chain?
A chainsaw chain can be sharpened up to 10 times, sometimes more, before the entire chain needs replacing. It's mostly dependent on two things; the amount of wear your chain incurs and the amount of metal removed every time you sharpen. Different materials can have a harder impact on the chainsaw chain.
How do you know if your chainsaw sprocket is worn out?
0:000:45Have You Ever Seen A Chainsaw Sprocket Worn Out Like This? #shortsYouTubeStart of suggested clipEnd of suggested clipQuick video here guys have you ever seen a chainsaw sprocket worn out this. Much. You can see theMoreQuick video here guys have you ever seen a chainsaw sprocket worn out this. Much. You can see the grooves.
How do you tighten the tension on a chainsaw?
2:164:05How-To Properly Adjust The Chain Tension On Your Chainsaw - VideoYouTubeStart of suggested clipEnd of suggested clipAnd now while you're holding the bar reach in and turn the adjusting screw clockwise. You can doMoreAnd now while you're holding the bar reach in and turn the adjusting screw clockwise. You can do this in increments of a quarter turn or half a turn if you want.
Do chainsaw chains stretch over time?
Chainsaw chains stretch and become loose as they wear off due to time and usage. New chains that have not been used before are going to stretch a lot more in the beginning during the break-in period. Loose chains should always be tightened as they are posing a health and safety risk.
How do you know if your chainsaw chain is too tight?
The chainsaw chain should feel snug but still pull freely. Finally, perform a "snap" test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position.
How tight should a chainsaw chain be Stihl?
0:281:33Chapter 5: Adjusting Your Chainsaw's Chain Tension - YouTubeYouTubeStart of suggested clipEnd of suggested clipCover. You should now have a slight up-and-down movement of the bar. Holding the tip of the bar upMoreCover. You should now have a slight up-and-down movement of the bar. Holding the tip of the bar up rotate. The adjustment screw clockwise until the chain is seated against the bottom rail of the bar.
How long will a chainsaw stay sharp?
On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
What type of chainsaw chain cuts the fastest?
full chisel chainA full chisel chain is a chain with square cornered teeth, and they're known for being the fastest cutting blade shape available. A full chisel chain also has a higher number of teeth than other chain options(full chisel is also known as a standard chisel chain).
Why does my chainsaw chain keep coming loose?
1. Chain Not Set Properly. One of the most common reasons why your chain might be coming loose is because it was not set properly . When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
Why does my chainsaw come loose?
If there are any kind of malfunctions or damage with the internal components, it can cause your chainsaw to come loose.
How to unlock a chainsaw chain?
Start by loosening up the nuts of the sidebar, which will give you some room for the chain and chainsaw guide bar along with easy access to your chain. If your chainsaw has a break that is attached directly to the side panel, you’ll need to unlock it before you proceed .
What tool do you use to tighten a chainsaw chain?
To get the job done, you will need to use a scench. A scrench is a special tool that is a combination of a screwdriver and a wrench and is meant specifically for tightening and loosening the different nuts of a chainsaw chain.
What happens when you don't tighten the clutch cover nuts?
When you don't have the clutch cover nuts tightened securely to the bolts, the position of the bar can shift and wreak havoc on the tension of your chain. 2. Temperature Fluctuations. This one is basic science - when metal gets warm, it expands. As you use your saw, it is naturally going to heat up and get larger.
What happens if your chain doesn't lift?
If the chain doesn’t lift at all, your chain is too tight - and if the drive links come clear off the bar, it’s too loose.
How to tell if chain bar is damaged?
To determine if there is any damage to your chain or bar, remove the chain, bar, and chain cover. Check for any debris around the bar and make sure it’s not worn down. If it is, you’ll notice that the rails are shallow. If that’s the case, it will need to be replaced.
Why does my chainsaw keep coming off?
When the chainsaw chain becomes loose, it is likely to come off and stop working. This can happen because of a variety of reasons including improper maintenance or too much pressure being applied while using the tool in difficult conditions. To fix this issue, you will need a replacement ...
Why does my chain come off?
A worn-out chainsaw bar is the main reason why your chain comes off. If you are noticing that many of your teeth have been bent , it’s time to get a new one. The next most common cause for loose chainsaws is when they’re not well adjusted or tensioned correctly on their sprockets.
How to adjust chainsaw tensioner?
Step 1. In order to adjust your chainsaw correctly, the first step is loosening and tightening both tensioners. If you have a brake that attaches on either side panel then start by removing it before unscrewing or unfastening any screws attached.
What happens if a chainsaw is jammed?
When your chainsaw chain is jammed and you cannot clear the jam yourself without damaging the saw or hurting yourself, it’s time for a professional to step in.
What is chainsaw chain made of?
Chainsaw chains are made of metal and they will start to wear down if not properly maintained.
Why do you need a new chainsaw chain?
A new chainsaw chain will make cutting through wood easier. There are many ways to ensure your chainsaw is working properly and keeping the chain clean, but when you’re out in the field, it’s not always easy.
How to keep gas flowing through engine?
Turn the saw’s choke (if applicable), this will help keep gas flowing through the engine for when you need to start over again when restarting it. Hold down on both handles of the saw while pulling or pushing the chainsaw chain in both directions until it gets back on.
Why does my chainsaw chain keep coming loose?
If your chainsaw chain keeps coming loose, the reason might be mechanical issues. Its tension will be measured by how big or small is the space between the sprocket and bar.
Why does my chainsaw throw off the chain?
If the chainsaw keeps throwing the chain off, another problem might be the bar rail might be in poor condition. This component is especially crucial in the operational sawing tasks and is the component that takes a lot of beating throughout its lifespan.
Why does my chainsaw chain jump off the bar?
If your chainsaw chain jumps off the bar many times, the likely perpetrator might be the wear and tear of the drive socket. Its function is to engineer propulsion off the chains, and because of that, it becomes worn-out.
What is a chainsaw bar?
A conventional chainsaw bar has a groove that rotates its outer edges. The chain has sharp teeth that run in the bar rails to enable the chain to run straightforwardly.
Why does my chainsaw keep loosening?
If it is the reason for the constant loosening of the chainsaw chain, it is a sign of a bigger problem. If left unfixed, the chain’s drive links will slowly lose their hold on the guiding bar. If this happens, it will come off frequently.
How to set up a chain with a coin?
There is a way called the dime method wherein you place the coin between the chain and the bar if its tension needs to be adjusted. It is the easiest way to ensure the chain is set up just right, but there are still others.
How many bolts are needed for chainsaw?
Some chainsaw models have automatic tension handles, but most typical ones have only one to two bolts in position to do the job. These bolts’ function is to lock the bar in place in relative capacity to the internal sprocket.
Why does my chainsaw keep coming loose?
There could be 3 reasons your chainsaw chain keeps coming loose: The chain was not set properly. A change in temperature. There is a mechanical issue. That’s the quick overview of the reasons, but it doesn’t help you understand the background, or how you can fix the problem.
What if Your Chainsaw Chain is Too Tight?
Most chainsaw users are more worried about their chain being too loose, rather than too tight. And to be fair, I understand the logic. It’s much more frightening to think your chainsaw might fly off (from being too loose) than it is to think about your chainsaw chain being excessively tight.
What happens if the bolts on a chainsaw are too loose?
If the bolts are too loose, then the position of the chainsaw bar can shift, and that will change the tension of your chain.
How to determine chainsaw tension?
The tension of a chainsaw is determined by the distance between the sprocket and the chainsaw bar. In the image below, you can see the internal hardware of a chainsaw where the sprocket, chain and bar all come together. All that’s really happening when you tighten your chainsaw chain, is that the chain tensioning mechanism is pulling ...
Why does my chain get loose?
The third reason your chainsaw chain might get loose (repeatedly), is an actual mechanical problem with your chainsaw. To understand this point, it’s helpful to better understand what is actually happening inside a chainsaw when you tighten it.
How to test chain tension?
How to Use the Pull Test, to Test Chain Tension. You can do the pull test after you’ve finished tightening your chain, to make sure it’s correct. All you have to do, is gently pull your chain away from the chainsaw bar.
Why does my chainsaw get tight?
This one comes down to physics. When metal gets warmer, it expands. When you’re using your chainsaw, as the chain heats up, it will literally get larger . This is probably the most common reason that a chainsaw will start tight, and then get loose.
