There are a couple of common causes for float mistakes in hot tubs; however The number one purpose of a spa showing the error code “FLO” is because of a grimy or wiped out filter system. Filters are usually the primary perpetrator as people don’t take time to clean the cartridges quite often, so the pleats get clogged and restrict the flow.
Why does my Kenmore hot tub keep saying Flo?
The most common reasons for the FLO error message are dirty filters, a low water level, clogged circulation pumps or bad sensors. The first thing you should do is check your tub’s water level. Top it off and see if this fixes the problem. Reset the tub GFI breaker to see if the error clears.
What does Flo mean on a hot tub?
When you get an “flo” message as a blunders code in your hot tub panel, expressed in numerous methods, “FL” “FLO” or ”FLOW.” It suggests that there’s no water flow or insufficient water flow through the hot tub heater which is caused due to a strain switch malfunctions or a flow switch malfunctions.
Why is the water not flowing in my hot tub?
The essential reason is the water flow through the spa control device, if the water isn’t always flowing at a charge to satisfy the pressure switch, it will result in one in every of the error codes indicated above. How to trouble shoot water flo error?
Why does my spa say Flo when I turn it on?
This may occur for a number of reasons. On your spa’s heater, there are sensors that read water pressure or there may be a pressure switch. These determine the error. The most common reasons for the FLO error message are dirty filters, a low water level, clogged circulation pumps or bad sensors.
What do you do when your hot tub says Flo?
The most common reasons for the FLO error message are dirty filters, a low water level, clogged circulation pumps or bad sensors. The first thing you should do is check your tub's water level. Top it off and see if this fixes the problem. Reset the tub GFI breaker to see if the error clears.
How do you reset the Flo on a hot tub?
0:201:29What To Do If Your Hot Tub Has A "FLO" Error Code - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can go back and flip your breaker in the on position let the spa run for about fifteen or twentyMoreYou can go back and flip your breaker in the on position let the spa run for about fifteen or twenty minutes very often it'll clear the flow message the spot will begin to heat.
What causes Flo error hot tub?
The most common cause of hot tub FLO errors is simply dirty filters. As filters become clogged with debris, they allow less water to pass through them. If they get too dirty they can restrict water flow enough to cause a FLO error.
How do you fix a low flow error on a hot tub?
0:072:26Fix a Flow Sensor Error on Your Hot Tub and Fix Your Spa Not HeatingYouTubeStart of suggested clipEnd of suggested clipTurn your spa off and put the filter in finally turn your spa back on again and run your jets for aMoreTurn your spa off and put the filter in finally turn your spa back on again and run your jets for a few minutes. This should remove any air that's in your lines.
Can you clean a hot tub flow switch?
To fix a flow error caused by dirty filters simply turn off the hot tub, remove the filters, then turn the hot tub back on. If the flow error goes away when the filters are out, give them a deep clean and put them back in.
How do you check a Jacuzzi flow switch?
How to Troubleshoot Flow Switch OperationTurn the unit off and unplug it from the power source for 30 seconds. ... Ensure the flow switch valve is open. ... Look at the water level in the hot tub. ... Clean out the filter. ... Check the output pressure and input pressure of the spa's jets and filter.More items...
How do you increase jet spa pressure?
0:071:39Tips to Increase Jet Pressure in your Hot Tub - YouTubeYouTubeStart of suggested clipEnd of suggested clipPump here so a couple things that you can do to actually increase the water pressure is oneMorePump here so a couple things that you can do to actually increase the water pressure is one waterfall over here. If you actually turn the waterfall which is to be this valve located on your tub.
How do I clean hot tub jets?
Clean Your Jets Take your hot tub jets. Minerals can build up on the jets, and you will need to clean them. The jets in your Master Spa can be removed for cleaning by turning them counter-clockwise until they release and then pulling out the jet. Soak the jets overnight in white vinegar and then rinse with water.
Why is my hot tub flashing error?
The water probably isn't flowing fast enough through the heater causing the temperature to increase. DO NOT USE THE HOT TUB while these error codes are flashing as the water will be scalding hot.
Why does my spa have a FLO error?
This may occur for a number of reasons. On your spa’s heater, there are sensors that read water pressure or there may be a pressure switch. These determine the error. The most common reasons for the FLO error message are dirty filters, a low water level, clogged circulation pumps or bad sensors.
What to do if your hot tub is still showing error message?
Clean your filters before putting them back in your tub to ensure the error message doesn’t pop up again. If your hot tub is still showing the message, it may be your circulation pump causing the problem.
How to tell if your circulation pump is clogged?
Also, make sure that it has power going into it. If your circulation pump is clogged, you might be hearing a whining noise. If there is no clear issue to the circulation pump, consult a professional to find out if you need a new one.
What does pump one mean in hot tub?
One is pump one is actually running on low speed and two, that there’s movement of water within the hot tub. Okay? So, if we have movement of water in the hot tub and pump one is running and the water is moving. So the water is running through this heater bearer and we still have FLO we’re going to say, “Hmm.
What does it mean when a heater is FLC?
Now, if you have an FLC, which means it’s reading closed when it’s not running. So, you’re going to go again. Qualify. Make sure the pump is not running and there’s no movement in the tub. There’s nothing flowing through this actual heater and it’s going FLC which means it’s closed.
What does the code FL1 mean on a hot tub?
You should always consult the manufacturers instruction booklet for specific information, however generally it is found that: FL1 hot tub code – indicates that there is an error with the flow switch and it is stuck in the open position. FL2 hot tub code – indicates that there is an error with the flow switch and it is stuck in the closed position.
What is an airlock in a hot tub?
An airlock is a large pocket of air trapped within the pipes of your hot tub. It will reduce the circulation of water as it will not properly flow through the hot tub heater. 5.
Where should the hot tub water line be?
The hot tub water line should be touching the bottom of the pillows when no one is in the spa. If your hot tub does not have pillows, then it will have a 'waterline' indicator somewhere on the shell or the filtration skimmer. Ensure that your hot tub water line meets the minimum requirements and top up if necessary. 2.
