It'll have breadboard ends. They are called that because the breadboards bakers used to use were made out of wood in the same manor the breadboard end is done on a table. In this regard, what are breadboard ends?
Full Answer
What is a breadboard end?
Feb 05, 2013 · The breadboard ends are essentially rails that are mortised to accept tenons on the ends of the panel. They serve the same basic purpose as cleats screwed to the inside face of solid wood panels on rustic furniture, except that breadboard end joints are a lot more elegant and forgiving of wood movement.
Why is it called a breadboard?
This terminology goes waaaaay back to the days of vacuum tubes. Generally, you would mount a number of tube-sockets on standoffs to a piece of wood (the actual "breadboard"), and do all the wiring with point-point wire and the components just hanging between the various devices. If you needed additional connection points, you would use a solder-lug terminal strip.
Is the breadboard end of a wood table a defect?
Aug 02, 2018 · What Are Breadboard Ends? A breadboard end is a piece of wood that’s joined to the end of a larger panel. Breadboard ends are the strips that are often found on the ends of some Amish tables. They run perpendicular to the larger panel and contribute to defining the form of the table panel. The breadboard runs cross-grain to the panel it is added to.
Should I put breadboard ends on my wood paneling?
Some breadboards are built on perforated phenolic of other dielectric base to hold components, In old days breadboards consisted grid of solderable posts nailed into a wood board (hence the name breadboard) to which component leads and wiring interconnections could be soldered to complete a circuit.
Why it is called breadboard?
What is a breadboard end?
Are breadboard ends necessary?
What are the two stripes on the side of a breadboard called?
Can you glue breadboard ends?
Can you use pocket holes on breadboard ends?
What are breadboard extensions?
How wide should breadboard ends be?
Do you need a breadboard for Arduino?
How do you end a breadboard?
What are the holes in a breadboard called?
What does it mean when an entire column on the breadboard turns green in the simulation?
What is breadboard end?
What Are Breadboard Ends? A breadboard end is a piece of wood that’s joined to the end of a larger panel. Breadboard ends are the strips that are often found on the ends of some Amish tables. They run perpendicular to the larger panel and contribute to defining the form of the table panel. The breadboard runs cross-grain to the panel it is added to.
What is tongue and groove?
A tongue and groove method is often used to fit the edges of a breadboard end with the table panel. One method involves a tenon that’s made along the length of the panel. The tenon is then fit into a groove that goes along the length of the breadboard. They are securely joined with wood dowels. This method of joinery makes for a strong connection ...
What is breadboard end?
Breadboard ends are a mechanical means to overcome a board’s natural tendency for one side to expand or contract at a greater rate than the other. Whenever you try to overcome the nature of wood, you run the risk of cracking, splitting or breaking something.
How to keep breadboard from cupping?
In the end, the best way to keep the primary board from cupping is to capture it in the breadboard end as much as possible. This narrows your joinery choices to sliding dovetails, tongue-and-groove joints, loose tenons or true mortise-and-tenons.
What is a dowel?
Dowels are the mechanical fasteners that keep the joint intact. While the surfaces of the dowel and the holes in the primary board are mostly side grain, there is considerably less side-grain-to-side-grain contact between the dowel and the breadboard end.
What is sliding dovetail?
Sliding dovetails sound like they might be the ultimate breadboard end joint – until you examine the flaws of using them in this manner. There’s a tremendous amount of the primary board captured in the breadboard, but grain direction is more problematic than with other options.
What happens if you don't use mortise and tenon joinery?
In reality, if you’re not using mortise-and-tenon joinery, you’re merely attaching a material that covers the end grain of the primary board. If you plan properly, you can get the most out of whatever joinery method you choose.
What is tongue and groove?
The tongue-and-groove work is really basic stub-tenon-type joinery. In other words, a groove is cut, usually in the breadboard end, that passes the entire length the piece. On the mating board there’s a matching tongue (stub tenon) that runs its entire width. Relief cut.
About Me
I'm a woodworker that does commissions for one of a kind, custom work. I will share and answer questions regarding my posts or anything else pertaining to woodworking. I also offer one on one instruction from my shop in Las Vegas that can be tailored around your schedule and what aspect of woodworking you'd like to learn more about.
Thursday, April 5, 2012
Everybody knows what a breadboard is and many of you have probably heard of the bread board end but let me take this blog as a way to explain it.
Solid-wood panels
When building a large solid-wood panel, such as a tabletop, you might be tempted to cap the ugly end grain by simply gluing another board across the end. Don't. The problem: Seasonal wood movement will cause that panel to cup at best, and self-destruct at worst, because the panel and cap expand and contract at different rates.
Mortise the end pieces
Center a 1⁄4 " mortise 2 1⁄8 " deep on one edge of each end piece, stopped 3⁄4 " from each end. Drill both ends of the mortise first. Then, drill evenly spaced holes between the ends.
Clean out the mortises
Drill overlapping holes to complete the mortise, starting at the ends. Then, chisel the ends and sides smooth and straight and square the corners.
Cut the tongue cheeks
Center a 1⁄4 " tongue 2" long on each end of the panel. Set the tablesaw fence 2" from the outside of a 3⁄4 " dado stack, and make several passes with the saw adjusted to cut 1⁄4 " deep.
Saw the shoulders
Lay out and cut the shoulders to make the tongue width 1⁄4 " less than the mortise length. A guide block keeps the saw square and prevents marring the panel end.
Drill dowel holes
Dry-assemble the end pieces, centering them on the panel width. Along a line 1" from the joint, drill 1⁄4 " holes 5⁄8 " deep at the middle and 2 3⁄4 " from each end.
Make slots in the tongue
Remove the end pieces, and drill 1⁄4 " holes on both sides of each end hole on the tongue to form 3⁄4 x 1⁄4 " slots. Straighten the slot sides. Replace the ends, and sand the joint flush.
