[SOLVED] – Let’s Fix It
- Ice Maker Is OFF. If your GE refrigerator ice maker stopped working, the first step is to make sure the ice maker is turned on.
- Improper GE Freezer Temperature. If a GE ice maker isn’t making ice, it may be too warm. ...
- Ice Maker is Jammed. ...
- Faulty Water Filter. ...
- Water Supply Line Issue. ...
- Icemaker Mold Thermostat. ...
- Defective Door Switch. ...
Why is my ge ice maker not making ice?
Why is my GE icemaker not making ice? If the water inlet valve is defective, or if it has insufficient pressure, it won't allow water to flow through. As a result, the ice maker won't make ice.
Why is my Refrigerator not cooling enough?
Refrigerator not cold enough
- Simple things you can check. Sometimes the most obvious answers are the correct ones. ...
- It may be a bad fan or air damper. Your refrigerator contains two fans that are a large part of the unit’s operation, and if they are not working, that ...
- Issues with major components. ...
Why is my ge fridge not cold?
My GE Side-by-Side Fridge Is Not Cooling
- Gaskets. One of the ways a refrigerator can lose its cool is by allowing the cool air to leak out around the doors.
- Lights. While the temperature may only fluctuate slightly as a result, a light inside the refrigerator can cause inefficient cooling.
- Evaporator Coil Frosting. ...
- Fan Motors. ...
How to fix a GE refrigerator ice maker?
The following are possible causes why a GE ice maker jams and how to fix them:
- Ice in Clumps Take the ice bucket out of the freezer and inspect the ice in it. ...
- Ice Chute Obstructed Ice or even dirt and debris can obstruct the chute through which ice goes through to the dispenser. ...
- Raker Bar Jammed
How do I reset my GE ice maker?
How To Reset A GE Ice MakerRemove the ice bucket.Locate the power switch.Turn the power switch to "OFF."Wait 30 seconds.Turn the ice maker back on.Push the feeler arm up three times.
How do I fix my GE ice maker?
0:423:03Refrigerator Not Making Ice? GE Fridge Repair #WR30X10093YouTubeStart of suggested clipEnd of suggested clipNext use a quarter inch socket or nut driver to remove the screws securing the auger motor. AssemblyMoreNext use a quarter inch socket or nut driver to remove the screws securing the auger motor. Assembly lift the motor assembly off of the mounting brackets disconnect the wire connector.
What do you do if your refrigerator ice maker is not making ice?
If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
How do I get my GE refrigerator to make ice?
0:091:37French Door Refrigerator Icemaker Operation - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you want to turn the icemaker off tap the icemaker or ice button depending on which modelMoreIf you want to turn the icemaker off tap the icemaker or ice button depending on which model refrigerator you have you may have to hold that button for 3 seconds to activate.
Why isn't my GE ice maker not working?
Check the Water Filter Another simple and often overlooked solution is that the water filter needs to be replaced. Some GE refrigerators have a sensor or timer that will stop the ice maker from working if the water filter needs to be changed. This is a safety feature to ensure the ice and water are safe to consume.
Where is the ice maker switch on a GE refrigerator?
For these refrigerator models, you turn the icemaker ON and OFF using the control panel on the fridge. ON/OFF Toggle Switch: This icemaker design has an ON/OFF switch similar to a light or power switch. ON is at the top of the toggle switch while OFF is at the bottom of the toggle switch.
Why does my fridge dispense water but not ice?
If the water inlet valve is defective, or if it has insufficient pressure, it won't allow water to flow through. As a result, the ice maker won't make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi.
Where is the reset button on ice maker?
You can find the reset button at the bottom of the ice maker. Remove the ice tray to locate it. Remove the ice tray. The red button you see is the reset button.
Will unplugging my fridge reset the ice maker?
Leave the refrigerator unplugged for 5 minutes. This will allow the ice system to reset. After 5 minutes, replug the refrigerator and turn the switch back on. This should cause the ice maker to start working again.
Can water filter cause ice maker not to work?
While a clogged water filter could be the cause of your ice maker not working, there are more common causes. First, make sure that your icemaker is simply turned on and plugged in. Check the power cord and make sure it is plugged in. Take a look at the feeler arm or paddle to confirm it can move freely.
How long does it take for a GE refrigerator to make ice?
24 hoursWith a new installation, the icemaker will not immediately start to make ice after being plugged in since the icemaker must reach a temperature of approximately 15 degrees Fahrenheit before a cycle is initiated. Please allow up to 24 hours for the icemaker to begin cycling and producing ice cubes.
Do all French door refrigerators have ice maker problems?
Many French-door refrigerators come with a through-the-door ice and water dispenser. But icemakers are a common failure point on refrigerators, so models with an ice dispenser tend to be more repair-prone than those without it.
How to fix a GE refrigerator that won't make ice?
The following are ways to solve the problem of a GE refrigerator not making ice: 1. Set the Temperature Right. Locate the temperature dial on your refrigerator and set each section’s temperature to the right degree. The ideal temperature for the fresh food compartment is 37 degrees Fahrenheit, while that of the freezer is 0 degrees Fahrenheit.
Why won't my ice maker make ice?
Another possible reason why your ice maker will not make ice is the unstable temperature within the refrigerator. So, ensure your refrigerator’s temperature is always set right. The right temperature for the refrigerating unit is 37 degrees Fahrenheit and 0 degrees Fahrenheit for the freezer.
What happens if a condenser fan is too stiff?
If they are stiff or don’t move freely, the fan motor is most likely defective and should be replaced. The condenser fan cools the refrigerant system. So, if it malfunctions, the refrigerant system will heat up, and as a result, affect ice production. 4.
How to keep ice in a refrigerator?
2. Stock Up the Unit Properly. Load the refrigerator up to ¾ full. If the appliance is not properly loaded, it may affect ice production. However, if the refrigerator is full, it will maintain a stable temperature and boost ice production. 3. Ensure the Condenser Fan Is Working.
Where is the condenser coil located?
Depending on the model of your refrigerator, the coils may be found on the back or top of the refrigerator. Then, on some other models, it is located under the appliance behind the base grille.
Can you turn off the ice maker on a refrigerator?
You may have unintentionally turned it off while loading the refrigerator. This is true if the ice maker switch is not on the control panel. Additionally, a defective icemaker switch will affect ice production. If this is the case, you may have to replace the ice maker assembly.
Does a refrigerator make ice?
So, if the refrigerator’s temperature is warmer than usual, it will take a longer time for ice production. Or, the refrigerator will not make ice at all. It is important to note that the temperature dial is located in different places. This depends on the model of the refrigerator.
1. Ice Maker Is OFF
If your GE refrigerator ice maker stopped working, the first step is to make sure the ice maker is turned on. The on/off switch should be a wire arm attached to the ice maker. If it is down, then the ice maker is on. If it is pushed up, then the ice maker is off.
2. Improper GE Freezer Temperature
If a GE ice maker isn’t making ice, it may be too warm. GE recommends that the freezer should be set to 0 to 5 degrees Fahrenheit for ice production. If it’s too hot, ice may not produce well or appear smaller or misshapen. On the other hand, if it’s too cold, ice may build up and frost will prevent ejection.
3. Ice Maker is Jammed
If your GE refrigerator ice maker is not working, it could be because of a particularly common issue. When a piece of ice doesn’t fall into the ice bin, a jam forms around the metal fingers of the ejector’s arm. The water from the melting ice freezes on the fingers, forming an ice bridge that blocks new cubes from being caught.
4. Faulty Water Filter
You should check to be sure that the water filter that you just replaced was installed and connected properly. If the refrigerator water filter was installed wrong, ice cubes will not form in the ice maker and can lead to other problems in the fridge.
5. Water Supply Line Issue
When your water line is not connected to your refrigerator, the water will not flow to the dispenser and you will not get any water or ice. The water shutoff valve on the refrigerator is closed- this prevents the water from coming into the door of the refrigerator.
6. Icemaker Mold Thermostat
The icemaker module has a temperature sensor that automatically dispenses ice when the temperature reaches about 15 degrees Fahrenheit. There are all sorts of complicated components that make up the ice maker module. One of them is the ice ejector. It turns the drum to release ice when it’s time for a refill.
7. Defective Door Switch
The water and ice dispenser in your fridge will turn off automatically when the door is open. To check if it’s working, just use a multimeter to measure the continuity on the door switch. If it doesn’t have continuity, then you’ll need to replace the switch.
How often does an icemaker purge air?
The icemaker will purge any air within the water supply line by cycling several times before filling with water. The first fill may only be a small amount of water but the second fill cycle would fill over this. It may overfill slightly but this is normal.
What position is the power setting on an icemaker?
Icemakers are typically shipped with the power setting in the Off position. Consult your Owner's Manual for instructions on how to turn on your icemaker. Download a copy of your Owner's Manual.
How long does it take for an ice maker to work?
The refrigerator and icemaker must be at the proper temperature. If just installed, the icemaker itself could take 24 hours to get cold enough to produce ice. The icemaker mold must reach 16 degrees F before a cycle will begin.
Does a refrigerator have an ice maker?
Refrigerator - New Icemaker Not Producing Ice. If an icemaker has just been installed in your refrigerator or if this is a newly installed refrigerator with an icemaker, there are a few things that must happen before it can produce ice.
How to get ice out of a freezer?
It is possible that moisture or frost could have formed behind the freezer wall on the auger motor. Set the dispenser for cubed ice.
What happens if the icemaker re-appears?
If condition re-appears, icemaker may be leaking or overfilling, which would require service. Ice may occasionally jam in the ice chute. If this occurs, open the left refrigerator door, open the ice box door on the inside of the left door, then remove the ice bucket.
How long does it take for ice to melt in a refrigerator?
Set the dispenser for cubed ice. Take a glass and push in on the cradle and hold in for 30-60 seconds. This will allow the motor to run to create some heat to melt the moisture or frost. If it doesn't dispense after 1 minute, then service would be required. See also Refrigerator - Ice Dispensing Intermittently.
1. Is the Ice Maker On?
This simple solution is more common than most people would want to admit. Most GE ice makers have either an on/off switch or a mechanical arm that needs to be down for the ice maker to work. Depending on the model, the on/off switch may be located on the ice maker or be accessed through the refrigerator’s digital display.
2. Is There a Diagnostic Function?
Some GE refrigerators will have a diagnostic function that may be able to identify the problem for you. Check the refrigerator’s manual or tech sheet for instructions to operate the diagnostic mode and interpret the results.
3. Reset the Ice Maker
Sometimes, an issue with the ice maker can be solved by performing a reset. Of course, if a defective part is causing the issue, the part will still need to be repaired or replaced. Often the ice maker will have a reset button or a way to reset it through the digital display panel.
4. Check the Mechanical Arm
As mentioned above, if your ice maker has a mechanical arm, it needs to be down for the ice maker to work. The arm can also fail if the arm’s spring has broken. Check the arm for signs that the spring has broken, and replace the arm if it is found to be defective.
5. Check the Water Filter
Another simple and often overlooked solution is that the water filter needs to be replaced. Some GE refrigerators have a sensor or timer that will stop the ice maker from working if the water filter needs to be changed. This is a safety feature to ensure the ice and water are safe to consume.
6. Is the Water Supply Line Connected?
Check that the water supply line is connected to the refrigerator and ice maker. Also check that the water is turned on. The water supply line can be checked where it connects to the back of the refrigerator and where it connects to the ice maker inside the refrigerator.
7. Check for Cracks in the Ice Tray
If your model features a rotating ice tray, a crack in the ice tray can stop the tray from rotating and emptying the ice. If cracked, it should be replaced.
What temperature does an ice maker need to be?
Freezer Temperature Too Warm. The icemaker must be 15 degrees to produce ice. Normal freezer temperature is around zero degrees F. Ice production can be further increased by decreasing the freezer temperature to -2F.
Why is my water line slow?
Small Cubes / Restriction in Water Line. Slow production can be a result of small ice cubes. It requires more cubes to fill the bucket. A restriction in the water supply line is generally a plumbing issue, not an issue with the icemaker or refrigerator.
Does food slow down ice production?
Very little food, or no food, in the refrigerator or freezer sections may slow down the production of ice. More food in the refrigerator allows temperatures to remain more stable. Add bottles of water or other items to add more volume.
1. Power Supply
Ensure that the ice maker is powered on. First, check the cord that connects it to the freezer to see if it is plugged in. if it is or your ice maker does not have one, check the switch. Make sure it is in the On position.
2. Water Supply
When you check the power supply to the ice maker and all is in order, then ensure that water gets into the ice maker. Check the tap that supplies water from the house to be sure it is turned on to the full.
3. Ice Bucket
Take a look inside the ice bucket to see if there is any ice in it. If there is, check the level of the ice. Too much of it will prompt the ice maker to stop dumping ice, especially if the ice is too high.
4. Ice Maker
Ice cubes may be caught inside the ice maker, making it near impossible for the ejector to work. So turn the ice machine off, open the ice maker and check it. If you see any ice cube caught in the ejector, remove it. Make sure nothing else is hindering the movement of the ejector.
5. Freezer Temperature
Make sure that the temperature inside the freezer is cold enough for the ice maker to work. It needs to be at 0 degrees Fahrenheit, at least. But if it needs to be higher, it should not go past 10 degrees. However, the best range is between 0 and 5 degrees Fahrenheit.
When to Reset the Ice Maker
If you try all the possible solutions above yet the ice maker still doesn’t dump ice, reset it. Shut off the power switch, usually in front of the machine, give it a space of 30 seconds, and power it again.
Why won't my GE ice maker get water?
The following are parts that cause a GE ice maker not to get water when they fail, and how to fix them: 1. Power. Be sure that the ice maker is on. Check the ice maker’s power cord. It should be plugged right into the back wall or the left side of the freezer compartment. Then, if the ice maker has a power switch, ...
What happens if your refrigerator doesn't dump ice?
If it dumps ice into the ice bucket after this time, the machine is functioning well. But if it does not dump ice after the waiting period, the ice maker is bad and needs a replacement. Buy the entire assembly, using your refrigerator’s model number, and replace the old one.
Why is my ice maker not letting water flow?
One of them is the inability of water to flow into the ice maker due to insufficient water pressure. 4. Water Pressure. Dispense water, if your refrigerator has a water dispenser, and see how long it takes to fill a glass ¾ full. If it takes more than 10 seconds, the pressure too low and needs to be increased.
What does it mean when water is in the ice maker?
If it does, it means water is now getting into it. 2. Water Fill Tube. The tube that goes into the ice maker from the back of the freezer is responsible for supplying water to the ice machine. To inspect it, you will have to take the ice maker out of the refrigerator.
Can you use a water filter on a GE refrigerator?
There is also the possibility you used the wrong type of water filter for the specific model of GE refrigerator you own. Therefore, always buy a new filter using the model number of your unit. As much as the ice maker can work without the refrigerator having a water filter, the absence of one can cause different issues.
