Why won’t my Washer’s spin cycle work?
When a washer’s spin cycle won’t work, there are typically a few reasons behind the problem. To begin, you must start by finding out what your washer is supposed to be doing based on the cycle settings.
Why is my Kenmore Elite washer not spinning?
Track down a blockage in the drainage system. Small items—like pennies, keys, buttons, or clothing clips—can fall out of pockets and off of clothing, then lodge themselves in the hoses that attach the washer to the drain pump. Ultimately, the blocked drainage prevents the machine from spinning.
How do I know if my washing machine spin switch is bad?
Inspect the spin switch. In a top-loading washer, a small protrusion on the underside of the lid depresses a switch when you close the lid, serving as a safety precaution to detect when the lid is closed. If the protrusion has bent out of shape, it may not trigger the switch as intended.
Why does my washing machine keep stopping and starting?
Check for an Imbalance: Typically with larger loads, if your washer is unbalanced, it can cause the spin cycle to stop working. This usually happens when the majority of the clothes get stuck to one side of the tub. In some cases, the tub will pitch noisily before stopping completely.
How do I fix the spin cycle on my washing machine?
0:543:23Washer Not Spinning - Motor Reset - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlease follow these three easy steps. 1 power down the unit by unplugging the washer from the outletMorePlease follow these three easy steps. 1 power down the unit by unplugging the washer from the outlet. To wait approximately one minute and plug the washer back into the outlet.
What is the problem if the washing machine wont spin?
Normally, your washing machine won't go into a spin cycle until it's been drained. The drainage hose may become clogged with debris from your clothing, or it could be kinked. If the hose is kinked or crushed, it will likely need to be replaced.
Why are my clothes too wet after the spin cycle?
Loading Too Many Items Overloading can lead to an imbalance that reduces the washer's spin speed, leaving clothes too wet after spin cycle completes. If the washer leaves clothes soaked after a large load, remove some items, redistribute others and run another rinse and spin cycle.
How much does it cost to fix spin cycle on washer?
To fix the parts that interrupt the spin cycle, homeowners can expect to pay professionals in the range of $150 to $500. Many problems with washing machines arise during the spin cycle.
Why won't my spin cycle work?
Problem: Your spin cycle won’t function as well – or at all – if the wash load is unbalanced. Generally, this happens when you’re trying to clean one or two heavy items, such as a comforter, bath sheet, or washable pet bed, and something clumps into a big, sullen lump.
Why won't my washing machine spin?
Problem: As a general rule, a washing machine doesn't spin normally unless the laundry load has been drained of water. Problems with draining usually stem from a drainage hose that’s become either kinked or clogged with small items like coins or buttons from your clothing. Fix: For the first issue, unkink the hose.
Why won't my washer spin?
Top loaders have a device called a lid switch that signals to the washer when the lid is not properly closed. If your lid switch stops doing its job , your washing machine doesn’t spin, as a safety precaution. Fix: On the underside of the lid, you’ll find a small protrusion that activates the switch when you close the lid.
Why is my washing machine spinning?
An unbalanced load of laundry is one of the most common causes of an inadequate spin cycle. Sometimes clothing can settle on one side of the drum, throwing off the motion of the washing machine. (This happens most often when washing large and heavy items like comforters or heavy coats.) Moreover, some newer machines won’t reach high speeds with off-balanced loads, which leaves clothes dripping wet. If you suspect a distribution problem, try rearranging your clumped-up wet laundry and running the spin cycle again.
How to test a spin cycle on a washer?
Test the theory by opening the lid, selecting the spin cycle on your washer, and then manually depressing the switch with a finger. If the machine starts spinning normally, simply re-bend the protrusion so it triggers the spin switch properly.
Why does my washer agitate?
A broken drive belt, or one that has slipped off the pulley wheel, can cause the washer to agitate during the wash cycle and yet—despite the noise of the motor running—the drum remain still during the spin cycle. To determine if this is the case, remove the back of the washer and visually check to see if the belt is still on the pulley. If not, you may need to replace the drive belt. Be sure to purchase one that’s made specifically for your brand and model of washer.
1. Incorrect Cycle Setting
Maytag washing machines have a wide range of settings, but the most common washer problems, like an incorrect wash cycle or spin setting, can all be easily corrected with a few clicks on your control panel. Use the gentle cycle when washing delicate items or those that are prone to stretching.
2. Washer is Unbalanced or Overloaded
Maytag washers are known for their strength and durability. Although they spin clothes very well, certain washer conditions can impact the spinning capacity. For instance, if the washing machine is overloaded or there’s a large item (for example, a blanket) in the washer, clothes may not be spun dry.
3. Defective Lid Switch Assembly
By closing the lid on your Maytag washer, the lid switch assembly is activated and causes the washer to turn on. While this system is convenient, it can become faulty over time — causing the washing machine not to turn on when the lid is closed.
4. Faulty Drive Belt
A washer drive belt connects the motor to the main drum. A damaged belt can prevent your washer from spinning, which then causes the clothes to sit in a wet mess. Two pulleys on either side of the drum connect the belt to the motor and help turn the drum during a cycle.
5. Failed Motor Coupling
If the washer spin cycle isn’t working, there are a number of possible causes. For example, if a motor coupling is faulty, it could be responsible for a washer spin cycle problem. A motor coupling links the transmission and motor so power can reach the washer drum.
6. Defective Door Latch
The washer door latch is a device that keeps the washer door shut during operation. It’s made of durable, high-quality material, and it prevents the washer from operating without its washer door shut. The latch also has a soft surface to prevent damage to the laundry tub.
