There are usually three reasons a Kenmore washer won’t spin clothes dry enough:
- Water won’t drain because the drain is clogged.
- The pump is malfunctioning, which won’t allow it to remove enough water throughout the washing, rinsing, and spinning cycles.
- The filter is dirty or damaged, stopping the water flow and making your clothes absorb the excess moisture.
Full Answer
Why is my Kenmore washing machine not agitating?
- Cycle Selector Switch – The cycle selector switch controls the speed of the motor and if it goes bad it can stop the motor from operating.
- Drive Belt – If the belt falls off or becomes worn the transmission will not turn and the machine will not agitate. ...
- Drive Motor – This motor turns the agitator and drum to wash your clothing. ...
Why is my washer not spinning all the water out?
| What You Need to Know
- Check Your Machine’s Power Supply. Perhaps one of the easiest answers to the question, “Why is my washer not draining or spinning?” is in its power source.
- Reset Your Machine. If your machine has this function, try performing a master reset on it. ...
- Check the Machine’s Position on the Floor. ...
- Rebalance the Washer’s Load. ...
- Inspect the Lid Switch. ...
Why is my Kenmore dishwasher not starting?
Troubleshoot and Diagnosis
- Electrical Issues. One of the most common problems with Kenmore dishwashers is electrical-related. ...
- Faulty Water Valve. ...
- Clogged or Kinky Water Hose. ...
- Child Lock is ON. ...
- Door is Not Closed Properly. ...
- Check Door Latch and Switch. ...
- Incorrect Dishwasher Cycle Settings. ...
- Touchpad Problem. ...
- Defective Timer. ...
- Faulty Drive Motor. ...
Why is my Kenmore dishwasher making noise?
How to Troubleshoot a Groaning Noise in My Dishwasher
- Reasons for Dishwasher Noise. One of the primary reasons why you may hear dishwasher noise is due to your dishwasher pump. ...
- Testing the Dishwasher Pump. After you unplug the dishwasher, remove the pump, which is behind the lower access panel. ...
- Wash Arm Seal and Bearing Ring. ...
- Inspect the Spray Arms. ...
What causes a Kenmore washer not to spin?
If the clutch is worn out, it may prevent the tub from spinning. If the clutch band kit is worn out, replace it. The drive pulley connects to the washer drum and works with the drive belt and motor to rotate the drum. If the drive pulley is worn out, the drive belt might slip off, preventing the washer from spinning.
Why does my washer turn on but not spin?
Here are a few common reasons a washer won't spin: The washing machine is too full. The load is improperly balanced. The washer itself isn't balanced correctly.
Why won't my Kenmore washer spin or agitate?
If the washing machine still does not agitate or spin, the motor control board may be defective. The motor control board is designed to provide power to the washing machine's motor. If the motor control board is defective, the washing machine may not function at all.
What does it mean when the spin cycle doesn't work?
Your washing machine may not be spinning properly because the loads are unbalanced or the drum isn't draining properly. First, rebalance the load and see if that fixes the problem. If not, you'll need to check and make sure the drain hose isn't plugged.
How do I reset my Kenmore washer?
1:173:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
How do you fix a washer that won't spin or agitate?
2:2011:01Washing Machine Won't Agitate - Top 8 Problems and Fixes - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou may have splines or flats that lock onto the shaft. If they're worn out the coupling will spinMoreYou may have splines or flats that lock onto the shaft. If they're worn out the coupling will spin freely on the shaft. And the washer won't agitate. If that's the case you'll need to replace it.
How do you fix a Kenmore washer that won't drain or spin?
0:086:44Washer Won't Drain or Spin: Troubleshooting VMW and Direct ...YouTubeStart of suggested clipEnd of suggested clipTurn the Machine off pull the drain hose out of the standpipe. And check for a clog at the end ofMoreTurn the Machine off pull the drain hose out of the standpipe. And check for a clog at the end of the hose. Sometimes lint or debris can build up in this area and prevent draining.
Why will my washer not spin or drain?
If your washer won't drain or spin, the water level control may be faulty. Open the machine's control panel and look for a plastic tube attached to the water level valve. If it's clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.
How do you fix a washer that will not spin?
How To Fix A Washer That Won't SpinLighten the load inside the washer. ... Rebalance the load in the washing machine. ... Check or repair the washing machine drain hose. ... Check for blown fuses. ... Check the washing machine lid safety switch. ... Replace the drive belt in your washing machine. ... Replace the motor in your washing machine.
How do you fix a washing machine that will not spin or drain?
What to Do When Your Washing Machine Won't DrainPerform a Master Reset. Unplug your washer for about one minute. ... Test the Lid Switch Assembly. ... See if the Drain Hose is Kinked. ... Check the Drain Hose or Pump for Clogs. ... Clean out the Coin Trap. ... Check the Water Level Control. ... Schedule Washing Machine Repair.
Why does the rear drum have a bearing?
The rear drum has a bearing or bearings in it to keep the inner tub spinning smoothly. If the tub bearing system is defective the washer can become very noisy and the tub can stop spinning. On some machines bearings are sold separately from the rear drum, however we recommend replacing both the outer drum and bearing as an assembly if the manufacturer offers the components together because removing and pressing in the new bearing can be exceptionally difficult. Be aware that replacing the outer...
What is tub bearing?
The tub bearing is mounted in the middle of the outer tub of the washing machine. The tub bearing helps to keep the inner tub spinning smoothly. If the tub bearing is defective, it can lock up and prevent the washer from spinning. The washer may also make a loud rumbling noise. Replacing the tub bearing is a very involved repair and will require disassembling most of the washer. If the tub bearing is defective, we recommend replacing both the outer tub and bearing as an assembly.
What happens if the door latch on a washer is not latched shut?
Once the washer door is shut, the washer can begin operating. If the washer door is not latched shut, the door switch will prevent the washer from operating. If the door latch is defective, the washer will not spin or start. The door latch can fail either mechanically or electrically. Inspect the door latch for damage. If the door latch is damaged, or does not close properly, replace it. To determine if the door latch has failed elect...
What does a lid switch do?
The lid switch assembly prevents the washer from spinning when the lid is open. If the lid switch assembly fails, the washer will not spin. To determine if the lid switch assembly is defective, use a multimeter to test the lid switch for continuity. If the lid switch does not have continuity, replace it.
Why does my washer not spin?
The stator interacts with the rotor to create a strong electromagnetic field which rotates the tub in either direction. If the windings on the stator are damaged, the washer will not spin or agitate. Check the stator for damaged windings or other defects.
How does a drive pulley work?
The drive pulley connects to the washer drum and works with the drive belt and motor to rotate the drum. If the drive pulley is worn out, the drive belt might slip off, preventing the washer from spinning. Remove the drive pulley and inspect it. If the drive pulley is defective, replace it.
How to test a door latch for continuity?
rically, use a multimeter to test any switches on the door latch for continuity. If one of the switches does not have continuity when activated, replace the switch.
How to fix a clogged lint trap on a washer?
Your most likely culprit is a clogged lint trap. If your washer is a newer one you have a little door down on the front bottom of the machine . Open it . You should have a large cap and a small hose. The hose is so you can drain the water before you pull the plug. Have a shallow bucket ready to empty water and take the plug out of the small hose. It will drain very slowly. If you want to speed this part up start the washer. When they first cycle they pump out first . This will force water out the small tube faster . You have to turn it on and off multiple times to get all the water out. Then o
Why is my washing machine not spinning?
The most common cause of a washing machine not spinning is a defective lid switch. That’s generally pretty easy to replace and not very expensive. A common cause for the washer not draining is a clogged drain hose or pump. Those can be checked rather easily.
How to drain water before pulling plug?
The hose is so you can drain the water before you pull the plug. Have a shallow bucket ready to empty water and take the plug out of the small hose. It will drain very slowly. If you want to speed this part up start the washer. When they first cycle they pump out first .
How to tell if clutch is oil or transmission?
Assuming the motor runs and the coupler is fine, then I suspect you have oil (from the transmission) on the clutch. Place a screwdriver in the lid switch hole. Once the motor is running to spin, grasp the inside of the empty basket and spin it counter-clockwise. If it starts spinning you have oil on the clutch. Replace the clutch, transmission and motor coupler.
Why won't my washer spin?
There are three possible reasons your washer isn’t spinning. The belt is broken, loose, or frayed. The belt transfers the power from the motor to the drum. If the belt can’t spin and turn the drum, the washer won’t spin. The motor.
Why is my washer not spinning?
There are three possible reasons your washer isn’t spinning. The belt is broken, loose, or frayed. The belt transfers the power from the motor to the drum.
What happens if the lid switch doesn't activate?
The lid/door switch. The switch has to be activated to let the motor activate. If the switch doesn’t activate then the motor won’t spin and the drum won’t spin.
Question: Kenmore 500 Washer Not Spinning?
My washer will drain the water out, but most of the time it will not spin. It makes a sound like it's trying too. I can reach inside and rotate the drum counter clock wise until I hear a click and most of the time that fixes it the problem. But I have to do this with almost every load, after the rinse cycle and on the final spin.
Question: Kenmore Washer Not Spinning?
My Kenmore washer is great, but sometimes the spin cycle doesn't come on. If I hit it on the corner where the lid connects to the washer it always starts it up, but I had someone tell me it was the belt wearing out. I am going to sell it and I want to be able to tell them the truth.
Question: Kenmore Elite Topload Washer Won't Always Begin Spin Cycle?
We run at least a load a day and this happens once every week or two. Pushing the button again is usually rewarded with a brief spin, but it can take a few tries before a normal cycle begins. I read a post here about a similar problem that was cured with a "$10 part" and would like more specific information or other suggestions, please?
Question: Kenmore Washer Won't Spin?
I have a Kenmore 80 series washer that just recently quit spinning. Well it will only spin if there is nothing in it, but if there's clothing in it all it does is make the noise as if it was spinning.
Question: Kenmore Washer Drains But Won't Spin?
My Kenmore series 500, top loading, one year old washer, drains and and the lid locks. But when it goes into spin mode, it immediately stops.
Question: Kenmore Washer Won't Spin?
My Kenmore washer is locked and it won't spin. What can I do to fix it?
Archive: Kenmore Washer Not Spinning
I have a Kenmore washing machine that doesn't spin. It washes, drains, and you can hear the spin cycle going, but it will not turn on its own.
How to read VAC on a washer?
You'll need a VOM (Volt Ohm Meter) set to read VAC. Set the timer to the start of the heavy wash cycle and allow the washer to run for 3 minutes. Measure the voltage drop between pin #5 of the ten pin plug on the speed control board and pin #5 of the six pin plug on the speed control board. If you read 120 VAC replace the speed control board. If you read 0 VAC replace the timer.
How long to run a test on a MCU?
The test has to be done at the begining of the heavy wash cycle and needs to run for three minutes.
Does the dial move in a spin cycle?
It begins the final spin cycle and spins infinitely. The dial does not move once it gets into that position.This happens on any cycle I put it in.
Why won't my washing machine spin?
Problem: As a general rule, a washing machine doesn't spin normally unless the laundry load has been drained of water. Problems with draining usually stem from a drainage hose that’s become either kinked or clogged with small items like coins or buttons from your clothing. Fix: For the first issue, unkink the hose.
Why won't my washer spin?
Top loaders have a device called a lid switch that signals to the washer when the lid is not properly closed. If your lid switch stops doing its job , your washing machine doesn’t spin, as a safety precaution. Fix: On the underside of the lid, you’ll find a small protrusion that activates the switch when you close the lid.
Why won't my spin cycle stop?
Problem: Your spin cycle won’t function as well – or at all – if the wash load is unbalanced. Generally, this happens when you’re trying to clean one or two heavy items, such as a comforter, bath sheet, or washable pet bed, and something clumps into a big, sullen lump. Interestingly, an unbalanced load can also cause the opposite problem, an ineffective spin cycle that won’t stop.
