Here’s how to check for one:
- Check the jet for any obstructions. This could be a broken piece of the jet, debris, or calcium buildup.
- Inspect the filter. Most cartridge filters are located in the hot tub’s skimmer. ...
- Check the drain at the bottom of the tub, making sure no debris is blocking that either.
Why are my hot tub jets not working?
Hot tub jets are the hardest working piece of equipment. Jets receive water outflow from the pump. When jets start failing, the most likely case is that your hot tub pump is not working correctly. You will need to diagnose hot tub problems relating to the pump. Check your pump’s priming to make sure it is working properly.
What should I do if my spa jets are pulsing?
If your spa jets appear to be pulsating or pausing, first check to make sure your filter is not clogged. If your filter appears to be okay, you should next take a look at your hot tub's water level. If there is too little water, air could be working its way into the system through the jets.
Why won't my spa heater work?
Older spa controls use an air button to activate the jet pump. The air switch button and the air hose can fail or lose effectiveness over time, and they may need to be replaced. Dirty Spa Filter? A dirty spa filter can slow water flow down noticeably, but not completely. Your spa heater won't work if your water flow rate is very low.
Why is there no pressure coming out of my Jets?
If you recently filled your hot tub and there is zero or little pressure coming from your jet nozzles, an air pocket may have formed in the line. This is known as an "air lock" and it will disrupt normal operation of your jets.
Why won't my Jacuzzi tub jets turn on?
Jets Are Not Working Properly When jets start failing, the most likely case is that your hot tub pump is not working correctly. You will need to diagnose hot tub problems relating to the pump. Check your pump's priming to make sure it is working properly. Open the access panel and the airlock valve close to the pump.
How do you reset the jets on a hot tub?
0:592:01How to RESET your HOT TUB - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd don't just turn it right back on you got to give it 30 seconds. Give the software give the logicMoreAnd don't just turn it right back on you got to give it 30 seconds. Give the software give the logic. Some time to actually reset. Wait 30 seconds flip your breakers.
Why are my pool spa jets not working?
Most of the reasons why pool jets stop working relate to low pressure in the jet system. Your pool jets rely on a system that includes the filter, the pump, and all the components that connect those pieces. When pressure drops, that system can no longer force water through the jets properly.
Why are my spa jets not bubbling?
Usually this problem is caused by either water or debris getting into the air pipe. If it is water in the pipe, then blowing into the pipe with a vacuum while the jets are running should clear it.
Where is the reset button on my spa?
The button is typically located on the side of the control box behind the hot tub's removable panel on the front side. Similar to disposal reset buttons, simply press the small red button in to reset it. But don't press it until you've figured out why it tripped. Resets are like circuit breakers.
How do you unclog a jet in a hot tub?
0:042:53Hot Tub Jets Stuck? The BEST Way To Fix & Clean Them - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then spray it into the outlet. Like this so when you spray water into the outlet you'll noticeMoreAnd then spray it into the outlet. Like this so when you spray water into the outlet you'll notice water squirting out all around the outside of the the jet.
How do you clear a clogged pool jet?
0:441:50How to Clear Blockages in the Circulation Lines of a Pool : Pool CareYouTubeStart of suggested clipEnd of suggested clipYou can also take a a plug. And put this into the suction line at the skimmer to kind of build up aMoreYou can also take a a plug. And put this into the suction line at the skimmer to kind of build up a little bit of pressure and then let it go and see if that will jostle it loose.
How do you remove an airlock from a spa?
2:223:07How to Fix an Air Lock in Your Spa : Pools & Spas - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then water will start to dribble out. Close the valve again tighten it and that will get rid ofMoreAnd then water will start to dribble out. Close the valve again tighten it and that will get rid of your air lock. So. This is Dan from pool and spa.
Where is the high limit reset button?
The High Limit Switch Needs to Be Reset or Replaced Simply reset by pressing the big red button on your spa pack. The high limit switch may be housed in a thermowell. If the water temperature in the thermowell is the same as the water temperature in the rest of the spa, the switch is damaged and needs to be replaced.
How do you adjust spa jets?
0:041:39How to Adjust the Jets and Controls on Your Splashes Oasis SpaYouTubeStart of suggested clipEnd of suggested clipIf you want to swap different jets around the spa to create a different type of massage. You canMoreIf you want to swap different jets around the spa to create a different type of massage. You can remove the jet faces by turning the jet. Off then twisting it sharply. And then unscrewing the face.
How do I reset my hot springs control panel?
0:041:04How To Reset a wireless Hotspring Highlife series control panelYouTubeStart of suggested clipEnd of suggested clipAnd you got to hold it there for a little while. And it will go black on you. And then eventuallyMoreAnd you got to hold it there for a little while. And it will go black on you. And then eventually you will start seeing where it's searching for the.
Where is the reset button on a Hot Springs hot tub?
0:491:58Hot Spring Highlife keypad reset - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you're just going to rest a finger on the top side. And just leave it there for a little bit.MoreAnd you're just going to rest a finger on the top side. And just leave it there for a little bit. And the top side itself will reset you can let your finger.
Why are my jets not working?
If the jets are still not working it could mean there is an airlock in hose connection to the jets and may need to be bleed through loosing the barrel unions on the circulation pump.
How to check if a jet pump is working?
Please follow the below steps: 1 Make sure your boost pump is working. 2 Check all water diverter and venturi valves are open. 3 Please check all jet faces are open and have been positioned correctly (all jet faces need to be turned past their first natural stopping point) 4 If the jets are still not working it could mean there is an airlock in hose connection to the jets and may need to be bleed through loosing the barrel unions on the circulation pump.
Why is my jet water inconsistent?
Inconsistent water flow could be the result of a clog – either in the jet itself, or in the filtration system.
Why does my water pump not send water to the jets?
This happens because, at some point during the refill, an air pocket forms in one of the filtration system’s lines. As a result, the pump isn’t able to send water to the jets.
How does hot tub water get sucked in?
Water is sucked in from the tub through the skimmer, cycles through the filtration system, goes through the hot tub heater to be warmed , and is then diverted to the return line piping where it eventually reaches the return jets.
How does a hot tub work?
A hot tub works on a cycling system, consisting of a filter, pipes, a pump, and a heater . The pump is the heartbeat of this system, pulling in water (the suction side), as well as pushing the water out (the pressure side).
Why is my tub not flowing?
Inconsistent water flow can also be caused by a low level of water in the tub.
What happens when air is forced into a jet?
Air outside of the jet is of higher pressure than the water inside the pipe. Air is then forced into the stream and mixes with the water. This results in a pressurized mixture of air and water, which is then shot out of the jets – and voilà, bubbles!
What are the components of a jet?
The jets have 3 components to them: water in, air in, and an air mixture outlet.
Why is my spa jet clogged?
In some cases, spa jets can become clogged from clumps of calcium or debris that have pushed through the filter.
What happens if a water pump is OFF?
If anything before the pump is loose or cracked, the pump will suck in air. The point that is leaking air when the pump is ON will also leak water when the pump is OFF. With the cabinet door open, shut off the pump and look for any spray or drips on the pipe that goes into the pump.
Is the Jet Adjustable?
Many jets are adjustable at the nozzle or by rotating the outer ring Many can be turned almost off, which increases flow to the other jets nearby. You may find it easier to manipulate the jet adjustment while the pump is off, but it's not necessary. Try turning the jet nozzle left or right, or turn the jet's outer ring or "scalloped bezel."
Are the Valves All Open?
For most spa and hot tub systems, there are two diverter valves on either side of the pump. These can be closed for equipment service without draining the entire spa. Sometimes these valves will vibrate into a closed position - especially slice valves, which are used on many spas. Check that the valves inside the cabinet are open.
How to check if a pump impeller is clogged?
If it is clogged, you will usually see some debris in the center eye of the impeller.
How many pumps does a hot tub have?
Some hot tubs have two pumps - a circulation pump for filtration and a jet booster pump. Many hot tubs just have a single, two-speed pump that accomplishes both functions. So another question would be, "Is the jet pump working?" or "Is the pump's high speed working?"
Can a spa cover clog a pump impeller?
For most hot tubs with a good spa cover, the tub stays pretty clean. But if your spa was left uncovered and took on leafy or seedy debris, this debris can clog up the pump impeller. The impeller is a closed vane type, and for many portable spas, there is no pump strainer basket to catch debris.
Why won’t my hot tub jets turn on?
If your hot tub isn’t getting enough water flow, or something else makes its way into the system and impedes water flow, the jets won’t work.
Do hot tub jets turn off automatically?
The jets in most hot tubs are designed to turn off after a certain amount of time. High-speed jets, for example, usually shut off after 15 minutes of use, while low-speed jets shut off after two hours.
Why are my hot tub jets not working?
Your hot tub jets might not be working because of an airlock in the system. You could also get jet issues if there has been a calcium build-up in the pipework or your pump is not operating properly. Hot tub jets can also clog up or get damaged stopping them from working properly. Non-working jets are a common problem with hot tubs and usually, ...
What does it mean when a hot tub jet isn't working?
Non-working jets are a common problem with hot tubs and usually, the issue will fall into one of three areas: One jet will not be working and the others will be fine, or none of the jets will work at all, or all of the jets will be working but with reduced pressure .
What is a clogged pump impeller?
Clogged pump impeller – The pump impeller is where the water enters the pump and it can sometimes become clogged with debris. To check to see if this is the case switch off the hot tub from the electrical supply and then turn off the valves either side of the pump.
What happens if a hot tub filter is clogged?
A clogged up filter – All of the water in the hot tub is pumped through the filter and it stands to reason that if the filter is clogged, old or blocked the pump will have to work harder, use more energy and the flow of water will be reduced.
What happens if the water level is too low?
If it is too low then you run the risk of air entering the system and causing an airlock. If airlock forms in the pump this can potentially prevent the pump from working and stop the jets from performing completely ...
How do I clean a hot tub jet?
How do I clean the jets on my hot tub? This can be a rather labor-intensive process as to do the job properly, you need to remove all of the jets and soak them in vinegar and water or a specialist jet cleaning solution. You can then use a soft brush to clean out any debris and make sure everything is clean before carefully rinsing and replacing the jets. It isn’t a good idea to remove all of the jets at once to do this job as it’s far too easy to forget which jet goes where and to then not be able to replace the jets in the right positions!
How to get rid of calcium build up in hot tub?
Sometimes calcium can break off in lumps and clumps leading to flow problems as well. The solution to this is to use a descaler to try to get rid of the scale . To prevent future build-ups of scale you need to regularly test your water for calcium hardness and adjust as necessary.
What happens if the jets in a tub aren't working?
If there’s voltage and your tub’s jets aren’t working, the pump is likely broken, and you will need to replace it. If there is no voltage, the pump has no connection to your power supply and will need to be reconnected.
Why is my jet not working in my bathtub?
Your jets in your bathtub are not working most likely due to your pump failing, or not working correctly. If your pump is fine, then there may be clogs in the water intake area, and you will need to clean them to improve the water flow to experience full functionality.
How to check if a tub filter is clogged?
In this case, turn the power off, find the pump and examine it. Your user’s manual should have a second about obstructions; use this as your guide for checking out the pump and filter for any potential clogs. A good test for the filter in particular is to run the tub without that filter. If the pressure improves, you can feel confident that the filter is either clogged or dirty.
Why are my jets in my bathtub so dirty?
Another reason that your bathtub jets could be improperly functioning is that it is overly dirty. When that is the case, make sure that you clean out all of the jets accordingly. All you need to do is fill the tub up using hot water and make sure that all of the jets are completely covered with at least 2 inches of water.
Why won't my jetted tub turn on?
Start by turning the tub off and ensuring that it is connected to a power supply. Verify that the breaker hasn’t tripped and that the power supply is working properly.
How to bleed a jetted tub?
Turn off your tub and find the bleed screws at the top of the filter and the end of the pump, loosening them as you go. When you’ve properly loosened those screws, turn the tub on. Repeat this a few times so that the jets can properly function as they were meant to once again.
Why does my pump make a humming noise?
If you hear a humming noise, it is because the motor isn’t turning properly, the shaft is frozen, a defective starting capacitor, or a potentially damaged pump. Likewise, you may notice that there are leaks under the pump; this is the result of a failure to seal. It is imperative that the pump seals.
Why Are My Pool Jets Not Working?
A weak pool jet is one of the most frequent problems for pool owners. If you ask a pool professional “Why are my pool jets not working?”, you may receive a blank stare and a pause. This reaction is due to the fact that we know the solution could be simple, but narrowing it down is time-consuming. We’ll separate the cause of low pool jet pressure into two parts. This will hopefully save you time from reading a section that doesn’t pertain to your situation. Part I will discuss low jet pressure when the filter gauge has a low PSI reading. In Part II we’ll discuss low jet pressure when the filter gauge has a high PSI reading.
Why is my pool pump pressure low?
Pool owners often tell us that the pool pump pressure is too low. With low jet pressure, the cause could be a damaged or clogged impeller. The pump will need to be split in half in order to inspect the impeller. Dog hair, pine needles and other small debris are main culprits for a clogged impeller. Replace the impeller if the body or any of the veins are cracked.
Why does my pool pump burn up?
A low water level can cause a pump to take in air. This will not only decrease flow, but it will cause the pump to run dry and burn up. Empty the skimmer basket and pump basket of any debris. This should be part of the regular pool maintenance, but it’s a simple task that is often overlooked.
Why is my PSI high?
The predominant factor for high PSI and low flow is a dirty filter. Cleaning the filter will normally lower the PSI and improve jet flow. In order to clean, sand and DE filters need to be backwashed and cartridge elements need to be hosed down. DE grids and cartridges can be soaked in a filter cleaner to remove oils and grease that aren’t removed during normal cleaning. If the PSI remains high after cleaning the filter, the filter media may need to be replaced. By media, we mean the sand, DE grids or cartridges.
How to tell if a pump has an air leak?
This would be the area between the skimmer and the pump. One way to determine if you have an air leak is by looking for air bubbles coming out of the return jets. Another sign is air in the pump strainer. The pump strainer, in most cases, should be full of water and have no visible air.
Can a snake work on a pool?
The clog will occur between the skimmer or vacuum port and the pump. A traditional plumbing snake will not usually work on pool plumbing, because of all the 90° turns. We recommend using an electrician’s fish tape or a drain cleaning water bladder.
Do pump strainers leak air?
The pump strainer, in most cases, should be full of water and have no visible air. Pump lid O-rings are a habitual offender of air leaks. The O-ring can expand or deteriorate over time and allow air to enter the pump.
Why are my hot tub jets not working?
Jets Are Not Working Properly. Hot tub jets are the hardest working piece of equipment. Jets receive water outflow from the pump. When jets start failing, the most likely case is that your hot tub pump is not working correctly. You will need to diagnose hot tub problems relating to the pump. Check your pump’s priming to make sure it is working ...
Why won't my hot tub heat up?
1. Your Hot Tub Won’t Heat Up Properly. If your hot tub won’t heat the water properly, it could be the heater element or low flow from your pump. Most heating failure result from corrosion caused by low PH in water supply. Any PH below 7.0 damages the heating element and trips the GFCI breaker.
What happens when you remove a hot tub?
But on removing the hot tub, you find the water ice cold, tub’s breaker trips when turned on, jet not working properly or your pump produces ear-splitting screech. Your evening is not working out as planned regardless of your hot tub water problems.
Why does my water pump make a squealing noise?
When you hear a grumbling, high-pitched squeal or growling noise from your pump, it is an indication of a problem. Remove clogs, top off your water and ensure all valves are open. Squealing sounds indicated bearings are worn out. You can try lubricating them, but eventually, you’ll have to replace the pump.
How to check if a water pump is working?
Check your pump’s priming to make sure it is working properly. Open the access panel and the airlock valve close to the pump. This releases air from the line and purge system, allowing more water to stream through the jets.
What does "dry" mean in a hot tub?
DRY: Means insufficient water is getting to the heating element. You may have to top your hot tub. Please use a hose filter to prevent impurities from getting into your spa and plumbing system. Double check to make sure no debris is present in your circulation system before restarting.
Does a hot tub trip the breaker when jets are turned on?
Does your hot tub trip the breaker when jets are turned on? Frequent GFCI tripping means you could spend a significant amount of time troubleshooting your hot tub. A malfunctioned hot tub GFCI breaker trip is easy to fix. However, you need to work with electricity to troubleshoot and repair. If you are uncomfortable, please call a professional. (hint hint, we’re professionals!!)
