Standard light switch cover plates, which are the most commonly used, measure 2.75 inches by 4.5 inches. There are two larger sized, preferred (midsized) and oversized (jumbo), which have a larger area to cover holes and imperfections. These covers measure 3.13 inches by 4.88 inches, and 5.5 inches by 3.5 inches, respectively.
What is the size of a light switch cover plate?
For a standard light switch cover plate, it will usually come in sizes of 2.75 inches or about 7 centimeters for the width with a length of 4.5 inches or 11 centimeters.
What is the standard size of a wall switch?
Typically, standard-size wall switches and outlet cover plates are used for new construction where construction tolerances are tighter. The standard size single switch or outlet cover plate is nominally 2.75 inches wide by 4.5 inches tall. The standard size two-gang switch or outlet cover plate measures 4.56 inches wide by 4.5 inches tall.
What is the size of a jumbo switch plate?
The larger two-gang oversized (jumbo) switch and outlet cover plate measures 5.31 inches wide by 5.25 inches tall. Replacing dingy, dirty, or older cover plates can immediately upgrade a room.
What is the standard size of a two-gang switch?
The standard size two-gang switch or outlet cover plate measures 4.56 inches wide by 4.5 inches tall.
Are all light switch plates the same size?
There are three common wall plate sizes: standard, midsize/midway and jumbo. When selecting a size, the plate should completely cover the electrical box opening. If the opening is oversized, you may need a jumbo plate to conceal it. Measure the opening to figure out the exact minimum height and width for your plate.
Do all switches have the same size?
Size, Weight The standard Nintendo Switch is about 4-inches high, 9.4-inches long and 0.55-inches deep with the Joy-Con controller attached. It also weighs about 0.29 Kg and 0.39 Kg with the controller. The new OLED model is also 4-inches high, a little longer at 9.5-inches and again 0.55-inches deep with Joy-Con.
How are outlet covers measured?
Place a ruler or tape measure against the plate or electrical box holes to get a precise measurement. Get the distance from the center of one screw hole to the center of the opposite screw hole (down to 32nds of an inch if need be).
Should all light switch covers match?
Ideally they should match the wall, or at least not stick out like the proverbial sore thumb. You can usually paint the switch plates to match the wall. Lightly sanding the plate first will help the paint adhere.
Are light switch covers standard size?
The standard size single switch or outlet cover plate is nominally 2.75 inches wide by 4.5 inches tall. The standard size two-gang switch or outlet cover plate measures 4.56 inches wide by 4.5 inches tall.
Are all wall switches the same?
Most of the common types of switches come in different styles, such as toggle, rocker, slider, or push-button. The style usually does not affect the switch function and electrical wiring, though it can make the selection process confusing.
How do I choose a switch plate cover?
How-To Guide for Selecting the Correct Light Switch CoversDevice Descriptions. ... Plate Orientation Pay attention to the orientation of decorative combination plates that have different device openings. ... Color and Finish. ... Decorating On A Budget. ... Oversized Switchplates May Be Required.
How do you cut a light switch cover off?
0:003:24How to Cut Down a Plastic Switch Plate or Outlet Cover - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you want to do first is mark. It. Then grab a speed square and reference your mark all theMoreSo what you want to do first is mark. It. Then grab a speed square and reference your mark all the way across the switch plate. Cover.
Are all rocker switches the same size?
Also note that there are three common outside dimensions for switch plates. They are normally labeled (in order of size) Standard, Midway, and Jumbo.
Should I paint my switch plates?
Architectural Digest suggests painting outlet covers the same color and finish as the trim in a room for a subtle, textural effect. Keep in mind that if you choose not to paint the covers, the outlet itself and the cover should be the same color.
How do you upgrade outlet covers?
1:223:10How To Update An Old Electrical Outlet - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put the lid on like that short street then hands tight the screw. Then you can just screw it in.MoreAnd put the lid on like that short street then hands tight the screw. Then you can just screw it in. Then you can just easily screw it in don't tighten down on it really really take cuz it's plastic.
Which is darker ivory or almond?
Our classic light ivory switch plates coordinate equally well with both ivory and almond electrical devices. The plates are just a shade lighter than most manufacturers' ivory devices for a fresher look and just a shade darker than most almond devices.
Light Switchplates Size Terms
GANG - The term "gang" refers to the width of the plate. A standard single-gang plate is 2-3/4" wide and houses 1 device. A 2-gang plate is 4-1/2" wide and houses 2 devices. A 3-gang plate houses 3 devices, and so on.
Switchplate Configuration Descriptions
Uses: toggle flip switches, toggle slide dimmers, locking switches, and other small rectangular devices
Switchplate Sizes and Overall Dimensions
Regular Switchplates are a standard 4-1/2" high and 5/32" deep; width varies based on the number of gangs:
Switchplate Screw Positions and Length
The following screw positions are standard on all brands of switch plates including Leviton Decora switch plates, Pass and Seymour wall plates, Brainerd, etc. The screw holes themselves are 5/16" across at the top and taper to a 3/16" opening at the botton.
Phone Jack Switchplates - Telephone Wall Plates
Telephone Jack 1, 2 and 3 plates are 2-3/4" W x 4-1/2" H x 1/8" D with 9/16" W x 3/4" H rectangular modular phone jack openings. Screw holes are spaced 3-5/16" apart from center to center on Telephone Jack 1, 2 and 3 plates.
Finishes and Colors
Cleaning - Switchplates are all metal, come with matching screws and may be cleaned with dusting spray applied to a soft clean cloth.
What is a switchplate cover?
Switchplate covers are one of the things to consider when enhancing your home décor. However, there are certain things to consider such as the right size for a switch outlet cover. There are factors to consider when selecting the right switch outlet cover for your home such as color and orientation. The following is a basic guide to help you ...
What is the difference between a duplex and a decora switch?
For instance, there a Decora switch outlet cover and a duplex outlet cover. Both covers are different in that, the Decora outlet is used for two receptacles, while the duplex outlet is used for one receptacle. Yet both types of outlets come in three different sizes.
How many plate covers do I need for a house?
Make a List. When remodeling or changing a home décor, every room in the house requires two to three wall plate covers. Ensure to indicate how many plate covers will be enough before purchasing. By knowing how may plate cover you need for the whole house, you'll be able to account for the cost.
Can a light outlet cover be rotated?
For instance, a normal light outlet cover can be rotated in all directions since it doesn't have any significant design on top of the cover. Therefore, select the right size, and the type of orientation that matches your taste and preference.
Why use a larger switch cover plate?
Use of a larger switch or outlet cover plate can save time and effort in non-standard applications where you would otherwise have to patch, sand, and/or repaint the wall around an outlet or switch to use a standard plate.
What is a combination switch and outlet cover plate?
Combination switch and outlet cover plates (for example a toggle switch and outlet or a toggle and rocker switch) Ganged wall switch and outlet cover plates (to cover two, three, or four switches or outlets in a row)
What is a single and ganged switch?
Tip. There are single and ganged switches and outlet cover plates that also protect USB ports and other data jacks located directly on the wall or other surfaces.
What is a wall switch plate?
Wall switches and outlet cover plates cover switches and outlets on walls and also those built into furniture, such as kitchen islands or other types of cabinetry. There are a few types of switch and plate covers, including: Toggle wall switch plates for switches that flip up and down.
What are the different types of switch plates?
Wall switches and outlet cover plates cover switches and outlets on walls and also those built into furniture, such as kitchen islands or other types of cabinetry. There are a few types of switch and plate covers, including: 1 Toggle wall switch plates for switches that flip up and down 2 Rocker wall switch plates, with a large rectangular opening, work with rocker, dimmer, slide, and tap switches 3 Outlet cover plates 4 Combination switch and outlet cover plates (for example a toggle switch and outlet or a toggle and rocker switch) 5 Ganged wall switch and outlet cover plates (to cover two, three, or four switches or outlets in a row)
What are thermoplastic cover plates made of?
Thermoplastic cover plates are made of durable nylon that won't typically crack. They typically come in standard colors such as white, beige, black, and other neutral colors.
