How to repurpose bifold closet doors?
There are several different ways to makeover a bifold door:
- Paint it a new or bright fun color
- Add decorative trim
- Reface it will thin plywood
- Turn it into a french door
- Add decorative hardware
How to easily install bifold door frame trim?
Mount the Bifold Door Hardware
- Attach the track to the header of the frame using the mounting hardware.
- After making sure it's centered, connect the upper pivot to the pivoting side of the frame opening. ...
- Screw the jamb bracket into the bottom corner of the frame. ...
- Lay each door panel flat on the ground and push them together to attach the hinges and mounting plates. ...
Can you shorten bifold doors?
The width of a bifold door can be cut up to ¼ inch on each side to fit better into a door rough opening. Tape off the side to be cut with painter’s tape then use a circular saw or planer to trim the width of the bifold door. Lightly sand the edges to remove burrs and paint the sides to reseal the door.
How to install, adjust or remove bifold closet doors?
Install the Bifold Door
- Have a partner help when installing bifold doors. ...
- Lock the door into place and adjust the height using the rotating arm or hinge pin, depending on the type of hardware included with your door.
- Attach the bottom pivot into the lower jamb bracket. ...
- Try opening and closing the door a few times to make sure it does not disengage from the track. ...
How to remove a door from the lower pivot pin?
How to cut 1 inch lumber?
Can bifold doors drag?
About this website
How do you cut a bifold door?
12:4113:47Bifold Doors, How I Trim A Bi-fold door - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo i am going to lift up on the door you should take the door off so you can get the nail gun inMoreSo i am going to lift up on the door you should take the door off so you can get the nail gun in straight if you shoot it on an angle it'll blow out at the back side.
Can you cut bifold doors to fit width?
Cut a piece of 2-by-2-by-96-inch fir to fit inside the door if you've cut more than 2 inches off the door and exposed the hollow core. Use the table saw to cut it to width and length. Place glue on both sides and tap it into the side of the door until it's flush with the side.
Can closet doors be trimmed?
Use a carpenter's square to draw a cut line that is square with the side of your doors. Apply painter's tape to the door, lining the edge up along the cut line and keeping the tape on the “good” side of the cut. The tape will help prevent the door from splintering while you cut. Remove any door hardware.
Can wooden bifold doors be cut down?
If you ordered a bifold door and find it's a bit too long for the door's height, it's a simple matter to trim the door to fit. Installing carpet with a thicker nap can sometimes cause the bifold door to drag. As a house settles over time, you might also find you need to adjust the height of a bifold door.
What is the finished opening for a 72 inch bifold door?
Bifold Finished Opening Widths are true to the measurement (a 3/0 is 36”, a 2/8 is 32”, a 6/0 is 72”, etc).
How much smaller should a bifold door be than the opening?
Bifold doors can have two or more panels with different widths. In general, the finished opening must be 1 inch higher than the doors for hardware installation and opening clearance. Also, the width of the doors is actually 1/2 inch smaller than shown to provide room for the doors to operate.
How much can I cut off hollow core bifold door?
How Much Can You Trim off a Hollow Core Door? Removing an inch or so from a hollow core door to allow for a thicker carpet, misread tape measure or wonky doorframe will be fine. However, cut off too much – roughly over 2 inches – and you may notice that the edge of the door is no longer solid.
How do you shave closet doors?
3:3722:54How to Trim and Rehang a Door - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I'm doing exactly the same thing on this side let me just push the bevel up into the corner ofMoreAnd I'm doing exactly the same thing on this side let me just push the bevel up into the corner of the frame. Now I'm just with a piece of wood. Make sure the two lines meet up.
How do you adjust the height of a bifold door?
1:234:18How to adjust your bifold doors - YouTubeYouTubeStart of suggested clipEnd of suggested clipThose little notches there those little teeth. And again you can slide this in or out towards theMoreThose little notches there those little teeth. And again you can slide this in or out towards the wall to make sure the gap at the bottom of the door is even. And that's all there is to it.
What are standard sizes for bifold doors?
Bifold closet doors typically fit an 80.5” or 96” tall opening. Typical widths can range from 24” to 72”. For spans up to 36”, your closet doors will have two panels or one door opening from the right or left.
What is the rough opening for bifold doors?
The rough opening should be 49 by 82 for a 48-by-80-inch door. This allows for 1/2-inch-thick drywall on both sides and at the top, 80 inches for the doors and hardware, and a 1-to- 1 1/2-inch space under the door. The space between the floor and the bottom of the door may vary depending on the type of flooring.
How do you cut the width of a door?
If you must to cut the height, trim the thicker rail at the bottom of the door. To trim the width, take evenly from both sides. To cut the door with a circular saw, place painter's tape along the cut line. Mark the line on the tape and score it with a utility knife to prevent chipping.
How do you cut the width of a door?
If you must to cut the height, trim the thicker rail at the bottom of the door. To trim the width, take evenly from both sides. To cut the door with a circular saw, place painter's tape along the cut line. Mark the line on the tape and score it with a utility knife to prevent chipping.
How much can you cut off the bottom of a hollow core bifold door?
Remember, you only have about an inch and a half available to lose from the average hollow core door. If you need to take off more than that, think about replacing the door instead. Start by drawing a pencil line to show where you're cutting, then grab a knife and a guide and score the surface of the door.
How do you cut a hollow bifold door?
0:547:51Cutting Bi Fold Hollow CORE DOOR - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff the table. So there we go step one and cutting the door to stabilize. It. Step two replacing theMoreOff the table. So there we go step one and cutting the door to stabilize. It. Step two replacing the sawn here now some people will use a speed square i have my line mark there on the bifold. Door.
What is the rough opening for 48 inch bifold doors?
Drywall Opening The rough opening should be 49 by 82 for a 48-by-80-inch door. This allows for 1/2-inch-thick drywall on both sides and at the top, 80 inches for the doors and hardware, and a 1-to- 1 1/2-inch space under the door.
how to cut width from bifold door? - DoItYourself.com
you should definitly special order them. If they are not in stock somewhere, it would only take a week or 2 to get in. The problem with cutting them as much as you need to is, the wood on the sides is only about 3/4" thick, so if you cut 1/2", you'll still have 1/4" in the door, a pain to get it out, and not thick enuf to hold the hinges and hardware.
Is it possible to cut down a bifold louver door?
Doors, Skylights and Windows - Is it possible to cut down a bifold louver door? - Here's my situation. I'm undertaking the project of enclosing my hot water heater and furnance which is currently open to our laundry room. I'm basically replacing the hot water heater moving it further back to allow me to build a wall
Shorten a Bifold Door - Fine Homebuilding
Nick. Just did some on my house and you cant cut much more than the 1/2" that you suggested. If you cut anymore than that you will have to do like CAG said and replace the piece of wood that was in there, there is a hole as you know, that has to be in the right location, other than that you can cut them down as much as you need.
How to cut bifold door width?from diywithchristine.com
You certainly can! Here’s how to cut the bifold door width: The width of a bifold door can be cut up to ¼ inch on each side to fit better into a door rough opening. Tape off the side to be cut with painter’s tape then use a circular saw or planer to trim the width of the bifold door. Lightly sand the edges to remove burrs and paint ...
How wide should a closet door be?from diywithchristine.com
If your closet rough opening is 24 inches wide, then the width of your single bifold door should be 23-½ inches. Measure the width of your door with a tape measure. Once you have all of your dimensions figured out, it’s time to move onto the next step!
Why did we accidentally do that to one of our closet doors?from diywithchristine.com
We accidentally did that to one of our closet doors because the rough opening was smaller than we realized.
Why do I have to paint the entire door?from diywithchristine.com
I wanted to avoid the potential moisture damage, and I had to paint the entire door anyways because we got the pre-primed ones to save $30 per door . That adds up quickly when you’re buying 14 doors… but it’s also A LOT of doors to paint…
What happens when you cut painter's tape on a door?from diywithchristine.com
The face of the door turns out much smoother when you cut through painter’s tape.
How thick is a rough opening door?from diywithchristine.com
If either dimension is a little bigger, then you will need to frame out the doorway with wood. For example, if your finished rough opening is 73” x 80-¾”, then an extra piece of wood that is 1 inch thick will need to be added to one side of the opening.
Can you trim a bifold door?from diywithchristine.com
It’s pretty straightforward, but there are some mistakes you’ll want to avoid while you’re trimming your bifold door.
How to remove a door from the lower pivot pin?
Slip the tip of a screwdriver or other flat object between the pivot pin and the upper door track. Release the spring-loaded pivot pin to lift the attached door off the lower pivot pin. Alternatively, lift the doors high enough to clear the lower pivot pin. Tilt the doors slightly and remove them from the upper pivot pin.
How to cut 1 inch lumber?
Install a fine-toothed blade in a circular saw. Measure the distance from the blade of the saw to the outer edge of its bottom plate. Attach a straight piece of scrap 1-inch lumber at that distance from the cutting line with a pair of wood clamps. This serves as your saw guide.
Can bifold doors drag?
The use of shims during installation takes care of any minor width adjustments. If you ordered a bifold door and find it’s a bit too long for the door’s height, it’s a simple matter to trim the door to fit. Installing carpet with a thicker nap can sometimes cause the bifold door to drag.
How to cut bifold door width?from diywithchristine.com
You certainly can! Here’s how to cut the bifold door width: The width of a bifold door can be cut up to ¼ inch on each side to fit better into a door rough opening. Tape off the side to be cut with painter’s tape then use a circular saw or planer to trim the width of the bifold door. Lightly sand the edges to remove burrs and paint ...
How wide should a closet door be?from diywithchristine.com
If your closet rough opening is 24 inches wide, then the width of your single bifold door should be 23-½ inches. Measure the width of your door with a tape measure. Once you have all of your dimensions figured out, it’s time to move onto the next step!
How deep are the top and bottom rails of Masonite bifold doors?from finehomebuilding.com
The updated answer is that both the top and bottom rails of Masonite bi-fold doors (specifically, I have the 6 panel version from HD) are mdf that are ~1-1/2" deep. You can check yourself by peeking in through the holes for the pivots. I stuck a nail in head first and the nail head catches on the lip of the hole on the inside. Marking the nail with your finger, take the nail out and measure to the bottom of the nail head. Voila.
How to remove a door from the lower pivot pin?from homeguides.sfgate.com
Slip the tip of a screwdriver or other flat object between the pivot pin and the upper door track. Release the spring-loaded pivot pin to lift the attached door off the lower pivot pin. Alternatively, lift the doors high enough to clear the lower pivot pin. Tilt the doors slightly and remove them from the upper pivot pin.
Why did we accidentally do that to one of our closet doors?from diywithchristine.com
We accidentally did that to one of our closet doors because the rough opening was smaller than we realized.
Why do I have to paint the entire door?from diywithchristine.com
I wanted to avoid the potential moisture damage, and I had to paint the entire door anyways because we got the pre-primed ones to save $30 per door . That adds up quickly when you’re buying 14 doors… but it’s also A LOT of doors to paint…
What happens when you cut painter's tape on a door?from diywithchristine.com
The face of the door turns out much smoother when you cut through painter’s tape.
How to cut bifold door width?from diywithchristine.com
You certainly can! Here’s how to cut the bifold door width: The width of a bifold door can be cut up to ¼ inch on each side to fit better into a door rough opening. Tape off the side to be cut with painter’s tape then use a circular saw or planer to trim the width of the bifold door. Lightly sand the edges to remove burrs and paint ...
How wide should a closet door be?from diywithchristine.com
If your closet rough opening is 24 inches wide, then the width of your single bifold door should be 23-½ inches. Measure the width of your door with a tape measure. Once you have all of your dimensions figured out, it’s time to move onto the next step!
How to remove a door from the lower pivot pin?from homeguides.sfgate.com
Slip the tip of a screwdriver or other flat object between the pivot pin and the upper door track. Release the spring-loaded pivot pin to lift the attached door off the lower pivot pin. Alternatively, lift the doors high enough to clear the lower pivot pin. Tilt the doors slightly and remove them from the upper pivot pin.
Why did we accidentally do that to one of our closet doors?from diywithchristine.com
We accidentally did that to one of our closet doors because the rough opening was smaller than we realized.
Why do I have to paint the entire door?from diywithchristine.com
I wanted to avoid the potential moisture damage, and I had to paint the entire door anyways because we got the pre-primed ones to save $30 per door . That adds up quickly when you’re buying 14 doors… but it’s also A LOT of doors to paint…
What happens when you cut painter's tape on a door?from diywithchristine.com
The face of the door turns out much smoother when you cut through painter’s tape.
How to cut 1 inch lumber?from homeguides.sfgate.com
Install a fine-toothed blade in a circular saw. Measure the distance from the blade of the saw to the outer edge of its bottom plate. Attach a straight piece of scrap 1-inch lumber at that distance from the cutting line with a pair of wood clamps. This serves as your saw guide.
How to remove a door from the lower pivot pin?
Slip the tip of a screwdriver or other flat object between the pivot pin and the upper door track. Release the spring-loaded pivot pin to lift the attached door off the lower pivot pin. Alternatively, lift the doors high enough to clear the lower pivot pin. Tilt the doors slightly and remove them from the upper pivot pin.
How to cut 1 inch lumber?
Install a fine-toothed blade in a circular saw. Measure the distance from the blade of the saw to the outer edge of its bottom plate. Attach a straight piece of scrap 1-inch lumber at that distance from the cutting line with a pair of wood clamps. This serves as your saw guide.
Can bifold doors drag?
The use of shims during installation takes care of any minor width adjustments. If you ordered a bifold door and find it’s a bit too long for the door’s height, it’s a simple matter to trim the door to fit. Installing carpet with a thicker nap can sometimes cause the bifold door to drag.
