can you put a tub in a walk in shower

How much does a walk in tub shower cost?

Walk-in tub shower combos cost an average of $2,500 to $6,000 to install, depending on the size and local labor rates in your area. Larger walk-in tubs or those with several add-on features will typically cost more. Any changes to your bathroom layout or plumbing as a result of adding the walk-in tub can result in a higher installation cost.

How to convert a bathtub into a walk-in shower?

Instructions Plan the Shower Footprint. Where feasible, choose a shower stall and pan that has the same footprint size as the bathtub. ... Secure Remodeling Permits. ... Shut off the Water Supply. ... Remove the Wall Surfaces. ... Disconnect the Plumbing. ... Remove the Bathtub. ... Inspect and Repair the Subfloor and Studs. ... Rough-in the Faucet and Showerhead. ... Rough-in the Shower Drain

How to convert a tub/shower to a walk in shower Part 1?

When you convert a tub in to a walk in shower; the easiest and most efficient use of time and materials is to put the walk in shower in the place left behind by the old tub. You can then use the old drain lines, water supply, and even parts of tub for the new walk-in shower.

How can I install a walk in tub shower myself?

Step-By-Step How to Build a Walk-In Shower

1. Demolition and Measuring. If you are installing a walk-in shower where a bathroom or tub already exists, you will first need to remove the previous items.
2. Choose the Right Kit. A shower kit can provide you with the tools and materials you need. ...
3. Gather Your Tools. ...
4. Install the Shower Floor. ...
5. Clean the Area. ...
6. Install the Shower Walls. ...
7. Install the Shower Curb. ...

More items...

Can you add a bathtub to a walk-in shower?

A freestanding bathtub and a separate walk-in shower are key ingredients in many dream bathrooms, but in reality, many bathrooms just aren't big enough to accommodate both. However, placing a tub inside a shower area can be a great way to get the benefits of both.

Can you put a freestanding tub inside a shower?

The answer is simple: when you're planning to take more showers than baths, a built-in works best. It's possible to set up a shower in a freestanding tub, but to keep water off the floor you have to suspend a shower rod and circle the tub with curtains.

How much does it cost to add a tub to a shower?

The cost to convert your bathtub to a shower during a bathroom remodel ranges from $1,200 to $8,000, with an average cost of $3,000. The total cost depends on size, accessibility features, fixtures, installation and other aspects.

How much does it cost to make a tub a walk-in shower?

The Average Cost of Converting a Tub Into a Walk-In Shower The installation and costs of converting a tub into a walk-in shower range between $5,997 and $11,950, with average coming in at $7,997. Although it may seem like a wide range for a simple project, many other factors contribute to the total cost.

Why are people putting bathtubs in the shower?

Placing the tub inside the shower means the entire area is waterproofed, and it actually simplifies the room's design.

What is it called when the tub is inside the shower?

A wet room is a space fully constructed with materials designed to get wet. Sometimes this means outfitting an entire bathroom in water-friendly materials. Many new wet rooms include a shower space and freestanding tub in their own glass enclosure separate from the sink and toilet areas.

How much does it cost to remove and install a bathtub?

The average rate for a general contractor is about $50 per hour. Considering the job could take up to 25 hours to complete, budget at least $1,250 for labor in addition to materials. A standard bathtub/shower combination averages $300 to $2,000 for materials.

Do plumbers install bathtubs?

Yes, among other services, plumbers do install and replace bathtubs. In addition to removing and installing your new bathtub, they will also connect the plumbing associated with the bathtub as well.

How long does it take to install a bathtub?

For the installation of the bathtub, you should allow an average of 4 hours.

What's the difference between a walk in shower and a stall?

Unlike standard stalls, walk-in showers don't require a curtain or door to block the spray of water, resulting in a spacious, open look.

What is the difference between a shower stall and a walk in shower?

Walk-in showers are essentially shower rooms without the shower screen or the shower tree. Unlike traditional shower enclosures, they don't have any doors or large glass panels. Rather, the entire shower area is open and fully tiled.

How much is a walk-in tub for seniors?

A basic walk-in tub with standard safety features can cost anywhere from $2,000 to $5,000. If you are looking for a walk-in tub with special features, such as a wheelchair accessible tub or tub with whirlpool jets, you can expect the average cost to rise to between $5,000 and $12,000.

Can you put a free standing tub in an alcove?

We often get asked whether it is suitable to install a freestanding bathtub in an alcove. The answer – absolutely! Freestanding bathtubs have been around for nearly 150 years, and they are still part of every day design. Available in endless shapes, colors and sizes.

Are freestanding tubs out of style?

Freestanding bathtubs. The freestanding bathtub is a current bathroom remodeling trend that may soon be going out of style. Like vessel sinks, freestanding bathtubs create more areas in your bathroom to clean because of the water and dirt that can get stuck between the floor and the bottom of the tub.

What are Japanese soaking tubs?

A Japanese soaking tub, also called an “ofuro,” is a tub that is traditionally meant to be used exclusively for soaking, not for bathing. You will shower before you enter the tub, or scoop water out from the tub to bathe yourself with soap or shampoo before entering the tub to rest and relax.

How much does a drop in tub cost?

The prices of walk-in tubs range from about $2,000 for a basic soaker to as much as $20,000 for a two-person tub offering a spa-like experience. Walk-in tub cost is determined mainly by features and materials.

Can you have a walk-in tub-shower combo?

Yes. Most walk-in tubs come with a handheld shower wand and can be upgraded with a full-size showerhead that works for a shower when standing or si...

Does a walk-in tub use more water than a regular tub?

Some walk-in tubs use a similar amount of water as a regular bathtub, which means you won’t need to buy a water heater with a greater capacity. How...

Which is better for seniors, a tub or shower?

Whether a shower or bath is safer depends on the senior’s needs and preferences, but for both, it’s beneficial that the model is a walk-in. As Adul...

What is the cost of a walk-in tub-shower combo?

According to Gerald Carpenter, a professional plumber, consultant, and adviser, “The most basic models without any massage features are available f...

What are the disadvantages of a walk-in tub?

Walk-in tubs are more expensive than regular tubs. Additionally, you must pay to install the new tub, which may include updating your plumbing and...

Will medicare pay for a walk-in tub?

Unfortunately, medicare does not cover walk-in tubs in most cases. This is due to the fact that they typically do not qualify as “durable medical e...

Are walk-in tubs tax-deductible?

In most cases, yes. If you purchase a walk-in tub as recommended or prescribed by your doctor, or if it is otherwise considered a medical necessity...

What does it mean to get rid of a bathtub and put in a walk in shower?

Modernizes the space: Getting rid of the bathtub and putting in a walk in shower definitely creates a modern and updated look to your bathroom. In addition, if the tub you’re getting rid of is a deep corner tub, that really dates your bathroom.

How much does a tile shower cost?

The accent tiles can run $10-$30 per square foot but you’ll likely only need 5 square feet. For more ideas, read my blog post on 10 Ways to Save Money on Your Renovation

How much does it cost to convert a tub to a shower?

Cost: To convert a tub to a shower—$5000-$8000. Time to complete: 1-2 weeks. Built in bench in walk in shower. Custom tempered glass shower wall and door. There are so many options when it comes to creating your walk in shower.

What happens if you only have one tub in your home?

Not a great option if it’s the only tub: If you only have one tub in your home, it could hurt the real estate value of your home. Young families will often require a tub in their home to bathe small children so if you eliminate the only tub in the house, you may be eliminating that demographic from purchasing your home. This may not matter if you don’t live in a neighbourhood that typically attracts young families. Consider consulting with a real estate agent before deciding that switching to a walk in shower isn’t the right decision for you

How much does a shower base cost?

There are good quality shower bases available that will cost $500-$600. Those are the ones you want to install! The other option you have is to build your own shower base. If you’re purchasing a good quality pre-made base, building it from scratch will cost about the same.

How wide is a walk in shower?

Creating a large shower: If you’re taking out an alcove tub, it allows you to create a 5’ wide walk in shower. This leaves lots of room within the shower. If you have difficulties later in life and need help in the shower either bathing or just getting in and out, there’s lots of room for another person to help out.

What is a niche in a shower?

Shower niche: This is a recessed niche that is great for holding shampoo, soap, etc. Benches: built across the one end of your shower, a small corner bench or even a purchased bench that can just be attached to your shower, some even with a hinge that allow them to be lowered out of the way when not in use.

Why Would You Put a Tub in the Shower?

If your shower area does not have a bathtub, incorporating one may seem like an unexpected but practical idea considering the new bathroom design trends.

What do you need to know before installing a bathtub in a shower?

Before you install a bathtub in the shower, you must first ensure that the tub materials are waterproof. Second, it is paramount to consider space. Do you have enough space to install the tub, or will you need to expand the shower room to create more space?

Can you use a freestanding tub in a shower?

A freestanding bathtub in the shower: This one is somewhat difficult to install and maintain compared to the built-in tub. Dust and mildew can build up right around the legs as well as the spaces behind it, and these areas can hardly even be reached when it’s time to clean. The good thing about this option though is that all the materials used are waterproof and therefore ideal for your shower setup. Some freestanding tub options that you can place in the shower are clawfoot tubs and Japanese soaking tubs. Both are a luxury addition but come with their own pros and cons.

Is it better to waterproof a tub or a shower?

Waterproofing a built-in tub is easier and more affordable compared to doing so for a standalone tub. If you are doing the installation on a fixed budget, you may want to opt for the built-in tub in the shower.

Do you have to have a floor drainage system for a bathtub in a shower?

Since you are installing the bathtub in the shower, you will not have much of a problem when it comes to floor drainage. This is already a shower: of course it must already have a good floor drainage system.

Is it easy to clean a built in tub?

A built-in tub in the shower : A built-in tub is the easiest when it comes to installation, not to mention that it is quite easy to clean and maintain. You can build one of these in the farthest corner of your shower, away from the shower door or curtain. With this type of tub, you will not have unused space that is exposed where dirt and water can accumulate. Thus, it’s quite easy to clean.

Can you use a tub and shower at the same time?

In short, a tub inside of a shower offers versatility and the benefits of both a bath and shower at the same time.

How high should walls be in a shower?

Tip: Make sure your walls are waterproofed up to a height of 6 feet in your shower and tub area's primary wet zone. Waterproof the walls at least 18 inches above the tub lip in a bathtub without a showerhead. There's plenty to love about this shower.

How many inches of drain line for shower?

Waterproofing is vital in these installations. Your bathtub will have a 1½- to-2-inch drain line that will need to travel through your shower’s waterproofing materials. Tubs in general are awkward and a pain to hook up, so there are a lot of factors to consider here.

What is the ledge on the right side of a shower?

For starters, the tiny ledge along the wall on the right is a great way to accommodate a smaller tub in a bigger space, while adding extra storage. The floor outside the tub is actually graded back to the shower, so everything drains with ease.

How much does a shower door cost?

Tip: A typical shower’s glass door and fixed panels can cost up to $2,000. I like how this shower-tub combination has a single wall panel and no door. A simple design change like this can dramatically reduce the cost of your new bathroom.

Is a shower tub waterproof?

If this modern tub were a tub shower, it’d be pretty difficult to waterproof because it’s designed as an undermount tub. Clean-lined tubs like this usually don’t have edging that connects the tub with the wall’s waterproofing. Placing the tub inside the shower means the entire area is waterproofed, and it actually simplifies the room’s design.

Is the floor outside the tub graded back to the shower?

The floor outside the tub is actually graded back to the shower, so everything drains with ease. This is a true wet room, and it looks great.

Can you put a bathtub in a shower?

Putting your bathtub in the shower may be an unexpected idea, but it’s a solid one and a growing trend in bathroom design.

What is clawfoot tub?

Clawfoot tubs can have classic rill rims, sipper tubs, double slipper tubs and double ended tubs. These features change the slope of the side of the tub for a more comfortable laying back position taken while bathing. This can make the tub a little awkward to shower in, as it is made for lounging not standing.

Why is it so hard to install a freestanding tub?

This is because there can be dust or mildew, etc that gets behind the tub or around the legs that is not cleaned as well or as much as the rest of the shower space.

Why is a Japanese soaking tub so popular?

The design of the Japanese soaking tub is to promote a sitting position in the tub versus a lying down position.

What is a built in tub?

A built in tub is one of the easiest to install and most maintainable types of tubs that can be placed inside a shower. This type of tub can be unique to each space by incorporating waterproof tiles on the floors and walls to go up the straight side (or sides) of the tub to create a seamless look.

Why is there a large tub in a shower?

Having this large of a space allows for features like dual sided sprayers, heated flooring, waterfall heads and much more. This situation would make it difficult to sit down and take a true bath, which is why in some cases there is section of the shower that includes a large tub. This also gives a nice place to rest a foot when shaving legs, or something to lean against.

What kind of tile is used in a walk in shower?

The walk-in shower with freestanding tub uses a glass subway tile for the walls and an hexagon floor tiles with bronze shower and tub hardware.

Do shower curtains sit on clawfoot tubs?

On top of that, shower curtains do not sit it a great way when it comes to clawfoot tubs. With having the tub inside of the shower it removes the need for a shower curtain to be inside the tub sticking to a person trying to shower.

What is a walk in tub?

Superior Walk-In Tubs provides bathtubs for those who need the therapeutic benefits of hot water immersion and the massaging action of spa jets. All models have a handheld shower, shower rod and curtain available. The ELITE model is compact and fits into the space of an existing shower stall or small bathtub. It comes with 16 spa jets and an anti-slip seat and floor. It also has an easy access front door that opens outward for maximum bathing space. Customers can order online or by phone and shipments take five to seven days. Superior Walk-In Tubs provides specialists who can answer questions or concerns, including recommendations for installation.

What is independent home walk in bathtub?

Independent Home provides several types of walk-in bathtubs that are ADA compliant and can fit existing bathroom layouts without requiring expensive remodeling. The Celebrity model is available in six sizes and can fit into the space of an existing shower stall or bathtub. It comes with a handheld shower head, and the 17-inch chair height allows for a deep soak. Customers can choose to mount the wide doors from the right or left. Customers can contact Independent Home by phone or complete an online form. Customers can also visit showrooms throughout the U.S. The “View Dealer Locator” link from the Contact Us page provides a list of dealers by state.

How long does it take to ship a spa jet?

It also has an easy access front door that opens outward for maximum bathing space. Customers can order online or by phone and shipments take five to seven days.

Is it expensive to add a bathtub?

Adding a standard sized bathtub may be expensive and require extensive design and plumbing modifications. However, options for those who want the benefit of a tub but have the space of a shower stall are available.

Do you need a bathtub for a shower?

Choosing a bathtub or a shower is a matter of lifestyle, budget and personal preference. Young families with children may need a bathtub for bathing. The elderly or disabled may require a tub for a soaking therapy. Adding a standard sized bathtub may be expensive and require extensive design and plumbing modifications. However, options for those who want the benefit of a tub but have the space of a shower stall are available.

Who is Helen Trencher?

In 2000 she published an article on the health benefits of drumming for "Colorado Mature Lifestyles." Trencher holds a Bachelor of Arts in education from Lehman College and a Master of Science in education from Fordham University.

How to tell if a tub is a soaker tub?

The most important thing I can tell you is if you are going to put your faucetry on the wall, the tub has to have a smooth straight edge. The tubs with any sort of lip or curviture will prevent you from having a sealed surface for the water to fall from the wall back into the tub, thus you would have water that would gather around the ledge. I agree with robaudio about the bain ultra tubs. Great manufacturer with many different options.

What is a free standing tub?

The free standing tub (e.g. clawfoot tub) with a wraparound shower curtain on a circular shower curtain rod. This is probably the simplest way to achieve a soaking tub/ standing shower combo. And if you do not car for the 'clawfoot' design there are many new free standing tubs that have bases other than clawed feet.

Why do tubs need a tile flange?

The tub needs to have an integral tile flange to allow it to be used for a shower application. It is a lip that prevents the water from pooling on a flat surface. If the tub does not have the tile flange, it should not be used for more than occasional showering, like in a guest bath.

How long is a soaking tub?

Say your space is 80 inches and your soaking tub is only 70 inches long. Bring one wall 10 inched closer to the end of the tub (or both walls 5 inches closer) and create cubby holes (shelves) for towels in the walled area.

Can you make a shower combo with a claw foot tub?

Another very, very simple (and elegant) was to make a soaking tub/standing shower combo is to install either a fee standing tub (such as a claw foot tub) or a drop in tub (oval or rectangular) and then... hang a 360 degree oval shower curtain that you can raise and lower by pulling on a chord, just like a window blind. Problem solved.

Can you use a claw foot tub with an overhead shower?

d. A wet design. Either a claw foot style tub or drop in tub can be coupled with an overhead shower with no shower curtain whatsoever if you tile and slope the floor toward a floor drain. If using a drop in tub, slightly angle the horizontal tiled surfaces surrounding the tub so there is no free standing water, so that any water runs off onto the floor and into the floor drain. There is no reason why this cannot be done. After all, the floors of showers are slightly sloped, tiled, horizontal surfaces!

Can you put tile down to the lip of a tub?

A 'drop in' tub with square corners where tiled walls can be brought right down to the lip of the tub so that there is are no flat, horizontal surfaces where standing water from a shower can accumulate. This might require bringing the wall a bit closer to the tub. No problem. It can be done.

What to do with a bathtub that has been removed?

With the bathtub removed, inspect the condition of the exposed wall studs and the subfloor where the tub was installed. Light carpentry work may be required to fix some of the studs or the subfloor where it is exposed by the removed tub.

What is a shower pan made of?

Most pans are made of acrylic or fiberglass, and in many cases, the directions will call for troweling on a bed of wet mortar to create a solid base that does not flex. Position the shower pan in the mortar bed, with the drainpipe riser centered in the drain opening, then attach the lip of the shower pan to the wall studs with nails or screws. Take pains to make sure the lip of the shower pan is level in both directions, which will ensure proper water drainage in the bottom of the pan.

What is rough in plumbing?

In addition to altering the drain lines as needed, the plumbing rough-in stage involves mounting the shower valve and showerhead arm on the studs, as well running the necessary pipes from the hot and cold branch lines, and between the shower faucet valve and the showerhead. Though the work is not necessarily difficult, a good amount of knowledge and experience with plumbing is required to do this work.

What does it mean to replace a bathtub with a shower?

Completely replacing the bathtub with a shower means removing everything in that space—tub, walls, even the ceiling and flooring—and installing a shower pan, shower controls and faucet, walls, and door.

How high should a shower valve be?

Generally, the valve body should be centered 45 to 48 inches above the shower floor, with the showerhead centered at 78 inches.

How long does it take to replace a tub with a shower?

Replacing a tub with a shower is a complex task that can take from two days to a full week to complete, but it is a project that often pays itself off after the dust has settled.

Where is the drain opening for a shower pan?

The shower drain opening for the new shower pan will probably be located in the center of the pan, while the drain openings for bathtubs are usually at the end. So it's likely you will need to do some carpentry and plumbing work to move the location of the drain before installing the shower pan. Some DIYers choose to hire a plumber to do this piece of technical work.

Can you adjust preshower temps in shower enclosure?

I built mine in for a couple of reasons, one, you can adjust preshower temps while in the shower enclosure without trying to avoid the ice water. Two, if you ever need to fill a bucket its much easier! Three, I already had the valve to do it.

Can I convert a 60x36 tub to a custom shower?

No have not had it get in the way yet, I converted a 60 x 36 tub to a custom shower with those as the inside dimensions

Can you take a shower with multiple heads?

Well with multiple heads in the shower (1 overhead & 1 wall mounted) the wife and I can comfortably take a shower together, without, banging anything that isn't supposed to be.