Can you use low temperature solder for jump rings?
There is only one temperament of solder that requires a lower heat (called low-temperature solder). Jump rings, therefore, do not require a solder that melts at a very high temperature. Cut extra-easy solder into very small chips using tin snips that do not exceed .03 inch (1 mm) squares.
Do Jump rings need to be secure?
If you use the right technique to open and close your jump rings, they should be secure. There are, however, certain factors like the weight of the jewelry that could make the jump ring open up or break. When stringing jewelry also, the string can pass through the slit of the jump ring if it’s not properly closed.
How do you use flux to solder jump rings?
Open the jump ring with a set of pliers using needle-nose pliers if the ring is small. Apply flux to both ends of the opened jump rings with a small, fine paintbrush. Flux is an agent that assists the solder in flowing into the joint. Flux comes in a variety of forms, but one common form is borax.
What are the different types of jump rings?
Jump rings, however, fall into two categories, that is closed and open jump rings. Open jump rings are loops that have a slit that allows them to be easily opened and closed. Closed ones are loops that are complete with no openings or slits. For such jump rings, you’ll need to cut them and solder them back together when done.
How do you seal jump rings without soldering?
0:031:23How to fuse a ring without solder - Quick Tricks - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're going to do is heat right here and fuse this ring together make sure that the piece isMoreSo we're going to do is heat right here and fuse this ring together make sure that the piece is clean. And add some flux to the joint. Now carefully heat up the piece and make the flux. So glossy.
When should you solder a jump ring?
1:074:49How to Solder a Jump Ring on Jewelry - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere should be a slight tension holding the seam closed soldering is not made to bridge gaps. NextMoreThere should be a slight tension holding the seam closed soldering is not made to bridge gaps. Next fire coat the piece wherever it will be heated to learn more about this process.
Can you solder jump rings?
There are two choices - soldering iron soldering and torch soldering. PLUS if you need to, you can still hallmark it. (because the metal of the jump rings can't get hot enough to melt and mix with the metal in the solder). You would ideally use a torch to apply enough heat to get a good solid join.
Do jump rings stay closed?
The only way to permanently secure jump rings is to solder them together. Some jump rings are already soldered closed; others are solder filled and can be soldered closed with the use of a butane torch. You might also consider using split rings (think of key rings) which are very secure.
How do I make sure jump rings stay closed?
0:462:29How to Properly Open and Close a Jumpring (and how NOT to!)YouTubeStart of suggested clipEnd of suggested clipThe other side. And then pull it toward you like. That close your jump rings move the pliers backMoreThe other side. And then pull it toward you like. That close your jump rings move the pliers back and forth until you hear a clicking sound that means the wire ends are touching each.
Can you use a soldering iron to close jump rings?
As long as the temperature of the soldering iron can reach the temperature of the solder, it can be used to solder the ring. Keep in mind that the metal also has to absorb enough heat to melt the solder.
How do you secure a jump ring?
To close, twist back towards you, letting the ends of the jump ring slide next to each other. To get a really secure fit, twist the ring slightly past the closed position and then back again letting the natural spring of the metal align the ends to a tight, closed position.
How do you join jump rings?
0:011:03How to Attach a Jump Ring - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt was close like this and I opened it this way I bent one side away from me and one side toward meMoreIt was close like this and I opened it this way I bent one side away from me and one side toward me I'm going to go ahead and place this clasp. On the ring and then attach it to the chain.
How do you strengthen a jump ring?
0:141:22Cool Tools | How to Work Harden Jump Rings - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I'm going to tumble this for about two hours tumbling work hardens the jump rings withoutMoreAnd I'm going to tumble this for about two hours tumbling work hardens the jump rings without distorting their shape or size after tumbling I use the scissors to cut the stem.
Can I use glue on jump rings?
Loctite® 454 Gel is the ideal glue to close a jumpring because it is made to adhere to smooth surfaces, dries clear and quick, and is in a gel form that fills gaps.
What are solder filled jump rings?
Jump rings are made from coiled wire and have an opening that allows you to insert it through a ring, loop or hole on another finding. A staple of the jewelry-making industry, these rings are ideal as attach rings for component designs, as strand or chain ends, and as links for creating chain.
What is the difference between open and closed jump rings?
Closed jump rings are continuous loops that do not have any openings. This usually means that the ring has been soldered shut if the jump ring is made out of a metal like sterling silver, or gold. As a rule of thumb, the jump ring should always be closed if you are using it as an ending for a bracelet or necklace.
What are solder filled jump rings?
Jump rings are made from coiled wire and have an opening that allows you to insert it through a ring, loop or hole on another finding. A staple of the jewelry-making industry, these rings are ideal as attach rings for component designs, as strand or chain ends, and as links for creating chain.
How do you solder a jump ring to a chain?
0:162:38Soldering a Jump Ring to Jewelry Chain - YouTubeYouTubeStart of suggested clipEnd of suggested clipTime. Don't forget now I've added a tiny bit of white out to the to the chain and where it's meetingMoreTime. Don't forget now I've added a tiny bit of white out to the to the chain and where it's meeting the jump ring and the reason I did that will prevent the solder from flowing down the chain.
How do you solder a jump ring on stained glass?
2:416:07Stained Glass Soldering pt. 2 :: Jump Rings & Beading the EdgesYouTubeStart of suggested clipEnd of suggested clipI will be soldering it to i use my grossing pliers to hold the ring in place. And then i'll take myMoreI will be soldering it to i use my grossing pliers to hold the ring in place. And then i'll take my solder and solder one side of the ring. And then the other.
How do you solder a jump ring to a pendant?
0:338:38How to Solder a Jump Ring and Bail (part 1) - YouTubeYouTubeStart of suggested clipEnd of suggested clipBecause we don't want a lot in there. The piece is relatively. Small thank you can you hold theMoreBecause we don't want a lot in there. The piece is relatively. Small thank you can you hold the striker pretty. Please. Thank you so you know when you boil up your solder. Just get in there really.
What happens if the chain is pulled and does not break the link?
if the chain is pulled and does not break the link comes open.
Is it good craftsmanship to make the most secure pieces you can?
It’s just good craftsmanship to make the most secure pieces you can.
Can you solder JR earrings?
In general, if the jump rings (JR) are of 20 gauge of less, they will pull apart too easily and should be fused or soldered. With earrings, where there is little likelihood of a tug that will pull the JR apart, soldering is not so important, and I usually forgo it.
Can you leave a chain link near a bracelet?
with ONE exception. I purposely leave one unsoldered or weak link near the clasp. That allows the chain to separate without injury to the wearer, and is simple to repair.
What tools do you need to solder jump rings?
When it comes to soldering a jump ring, you will require an extra-easy solder, tin snips, a pair of pliers, flux, small and fine paintbrush, water, copper tongs, soldering iron, jump rings, and a charcoal block.
How to open a jump ring?
Take your jump ring and open it using a set of pliers. Ensure you use a pair of pliers that will perfectly fit your jump ring.
How to pick up solder chips?
Start picking up your extra-easy solders chips using the tip of your small and fine paintbrush. Once this is done, you will place the solder chip on your jump ring joint and then turn on the soldering torch.
How to remove jump rings from pickle?
After a while, you will remove your jump rings from the pickle solution; ensure that you use copper tongs for this process. Once they are out, you should rinse the rings using water. You will then repeat the whole process for each jump ring.
What happens when solder melts?
As the solder starts melting, it will be having a liquid appearance during this stage. You will then watch you solder as it flows towards the hottest point on your jump ring.
What is a jump ring?
Jump rings are essential when it comes to making chains, chainmail, and jewelry. They are often designed by wrapping a wire around the mandrel, making a coil, and cut the loop using sure to create individual rings.
Do you solder jump rings?
In this article, we shall be focusing on how to solder jump rings with a soldering iron.
How to use jump rings?
To start with, you will need two pairs of flat-nosed or snipe-nosed pliers. Use the pairs to hold the jump ring properly on both ends. At this point is where most people make a mistake, by assuming that the ring is opened by pulling both sides apart and away from each other. This will weaken the jump ring and you will not be able to close it securely. The correct way is to twist one side of the jump ring away from you and the other towards you.
How Does a Jump Ring Work?
As we’ve already mentioned, jump rings sole function is to hold rings together. How they work may seem very simple, since it is a matter of opening and closing the rings. There is, however, the correct and wrong way of opening and closing jump rings.
What Is a Jump Rings in Jewelry Making?
Jump rings are classics and essential in every jeweler’s tool kit. Although they go unnoticed, they help hold your jewelry together.
What is the best tool for opening and closing jump rings?
When it comes to opening or closing jump rings, pliers, especially the flat-nosed ones are very handy. They make the whole process simpler by either helping with gripping or holding the jump rings securely in place. But what happens when you don’t have pliers in hand when you need them?
Why are jump rings important?
Jump rings are essential when it comes to making any jewelry. It is also easy to work with them if you have the right tools and the correct knowledge of how the rings should be handled.
What are jump rings made of?
They are made in different sizes, shapes, and textures, using different materials, usually metal. Jump rings, however, fall into two categories, that is closed and open jump rings.
Do you need pliers to use jump rings?
Luckily you don’t necessarily need pliers to work with jump rings. If the jump rings are large enough, you can use your hands to twist them closed. For extra grip, you can use the kitchen mitt while working with the rings. Kitchen tongs are also great alternatives for pliers when handling larger jump rings. They may not be as secure at griping but they are better than nothing. If the rings are too small, then it may be harder to use your hands or tongs, but you can use tweezers. They are like tiny pliers and would therefore be perfect for the job.
