GAF requires non-corroding metal drip edges at the eaves where a Silver Pledge® or Golden Pledge® Limited Warranty is sought. As a matter of good roofing practice, however, GAF strongly recommends that drip edges be installed at the rakes and eaves on all GAF shingle roofs.
Where should shingles be installed on a GAF roof?
As a matter of good roofing practice, however, GAF strongly recommends that drip edges be installed at the rakes and eaves on all GAF shingle roofs. How Should Shingles Be Installed Over Drip Edge? Shingles should be installed over the drip edge a minimum of 3/8” (9 mm) at both the eave edge and the rake edge.
What is a drip edge on a roof?
The drip edge also gives us a nice straight edge with which to align roof shingles, slates or other roofing material. Drip edge varies in dimensions but typically the flange that nails to the roof surface is about 2.5" wide and the vertical edge that directs roof runoff down and away is about 1.5" in depth.
What is drip edge flashing?
That is, the drip edge flashing is the first item installed onto the roof sheathing (or atop old shingles in a multi-layer shingle re-roof job).
How do I choose the right drip edge for my gutter?
Take a look also at the down-facing bend of the drip edge to be sure that it will send water into the gutter and not behind it. Drip edge varies in dimensions but typically the flange that nails to the roof surface is about 2.5" wide and the vertical edge that directs roof runoff down and away is about 1.5" in depth.
Is drip edge mandatory?
The IRC now requires a drip edge for all asphalt roof installations and provides direction for its proper installation. Underlayment must lap over the drip edge at the eaves. At the rake edges (the sloped edges that are referred to as “gables” in the code text), the drip edge must be installed over the underlayment.
Do shingle manufacturers require drip edge?
8.3. A drip edge is required to be provided at the eaves and rakes of asphalt shingle roof systems. A drip edge's flange should extend back onto the roof surface a minimum of 2 inches.
How do I install GAF drip edge?
1:072:04How to Install Drip Edge on a Roof | Mastering the Roof by GAF - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst the drip edge must be corrosion resistant second the drip edge should be applied directly toMoreFirst the drip edge must be corrosion resistant second the drip edge should be applied directly to the deck along the eaves. And then underlayment should be placed over the drip edge.
Where is drip edge needed?
The drip edge should be installed on top of the underlayment at all rakes, and below or on top of the underlayment at the eaves. At the eaves, when installing the drip edge on top the underlayment, a 4-inch wide layer of asphalt roof cement (complying with the ASTM D4586, Type I or Type II) is required.
Do you need a drip edge for new roof?
Not Necessary but Highly Recommended Regardless of the kind of roof you have, we highly recommend installing drip edges. Keep in mind that improper installation of any roofing component can create gaps, rendering any waterproofing solution useless.
When did drip edge become code?
Drip edges have been required by the International Residential Code since the 2012 revision. Most states in the U.S. have adopted the IRC, which means that drip edges are required for most buildings in those states. Because of how important it is, a drip edge is something that any building owner should consider.
Do shingles have to overhang drip edge?
Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
Should you use drip edge touch fascia?
Tack the end into position with the roofing nails and press the nail within the drip edge and into the roof covering. But do not push it through the fascia.
Does Owens Corning require drip edge?
The Owens Corning website recommends installing a drip edge on all roofs to be covered with asphalt shingles. For a drip edge to properly guide water away from your roof's components, it must be installed correctly. Specifically, roofing professionals should install a drip edge: At all rakes: on top of the underlayment.
Should drip edge be installed behind gutters?
It is recommended that gutters are placed under or 'behind' the drip edge of your roof. A drip edge refers to a component that hangs over the roof and has an outward projecting lower edge.
Do you need flashing and drip edge?
It helps direct rainwater off of the roof, either into a gutter or onto the ground. Without the flashing, rainwater could adhere to the edges of the roof and saturate important structural components. Drip edge flashing helps protect the roof decking, wood soffits, and wood trim from rot.
Does drip edge go over or under ice and water shield?
Ice and water protector needs to be installed directly onto the roof deck after you have placed the drip edge at the eave. (The drip edge will be installed over the ice and water protector and other underlayments at roof rake edges.)
Do shingles need to overhang the drip edge?
Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
Does Owens Corning require drip edge?
The Owens Corning website recommends installing a drip edge on all roofs to be covered with asphalt shingles. For a drip edge to properly guide water away from your roof's components, it must be installed correctly. Specifically, roofing professionals should install a drip edge: At all rakes: on top of the underlayment.
Do you need flashing and drip edge?
It helps direct rainwater off of the roof, either into a gutter or onto the ground. Without the flashing, rainwater could adhere to the edges of the roof and saturate important structural components. Drip edge flashing helps protect the roof decking, wood soffits, and wood trim from rot.
Should you use drip edge touch fascia?
Tack the end into position with the roofing nails and press the nail within the drip edge and into the roof covering. But do not push it through the fascia.
What is drip edge?
The drip edge also gives us a nice straight edge with which to align roof shingles, slates or other roofing material. Drip edge varies in dimensions but typically the flange that nails to the roof surface is about 2.5" wide and the vertical edge that directs roof runoff down and away is about 1.5" in depth.
Where should I install drip edge?
The drip edge should be installed on top of the underlayment at all rakes, and below or on top of the underlayment at the eaves. At the eaves, when installing the drip edge on top the underlayment, a 4-inch wide layer of asphalt roof cement (complying with the ASTM D4586, Type I or Type II) is required.
What is drip edge flashing?
Roof drip edge flashing serves multiple functions on a building, the foremost of which is to assist water in leaving the roof edge with minimum damage to other building components by directing the water off of the roof and into the gutter.
How deep is a drip edge?
Drip edge varies in dimensions but typically the flange that nails to the roof surface is about 2.5" wide and the vertical edge that directs roof runoff down and away is about 1.5" in depth. Lengths of drip vary but typically it's sold in ten foot lengths (120").
What is the orange arrow on a roof?
Orange arrow: points to the installation of ice and water shield along the lower roof eaves - protecting against ice dam leaks that are common on un-vented roofs in cold-weather or snow-climates. Install the ice and water shield membrane so that it laps securely over and bonds to the surface of the drip edge.
What happens if there is no gutter?
if there is no gutter, water leaves the edge and zooms out into space away from the building. . If there is a gutter, water leaving the lower roof edge is directed into the gutter, not behind it, not down building walls, not where we don't want it to go. The brown drip edge is properly installed and is doing its job.
Is Probabky required?
Probabky recommended not required except when an inspector makes strict interpretation of a general reqiirement to follow the manufacturer's instructions and those show the drip edge - as most do.
How to report a warranty claim to GAF?
You must notify GAF about any claim within 30 days after you notice a problem. You may report a claim online at gaf.com/contact, by calling GAF at 1-800-458-1860, sending an email to [email protected], or by sending a notice in writing to: GAF, Warranty Claims Department, 1 Campus Drive, Parsippany, NJ 07054, USA. You will then be provided with com-plete details about submitting your claim. You will be required to provide proof of the date your shingles or accessories were installed and that you were the owner of the property at that time (or that the warranty was properly transferred to you). You may be required to send to GAF, at your expense, photographs and sample products for testing. Within a reasonable time after proper notification, GAF will evaluate your claim and resolve it in accordance with the terms of this limited warranty. If you repair or replace your GAF Products before you notify GAF about your claim or before GAF has completed its evaluation of your claim, your claim may be denied. If you need to repair or replace your GAF Products before your claim is resolved, you MUST provide GAF with reasonable notice. NOTE: Notice to your contractor, dealer, or home builder is NOT notice to GAF. You should retain this document for your records in the unlikely event that you need to file a claim.
Does GAF have a warranty on shingles?
GAF Warranty Company, LLC, a subsidiary of GAF, warrants that your GAF Roofing Shingles will remain free from manufacturing defects that adversely affect their performance during the applicable Smart Choice® Protection Period or that cause leaks for the remainder of the applicable warranty term and that your GAF Accessory Products will remain free from manufacturing defects that adversely affect their performance during the applicable warranty term. Note: Wind Warranty and Algae Warranty are covered separately below.
Does GAF warranty apply to starter strip shingles?
This limited warranty does not apply to starter strip shingles. GAF warrants to you that your GAF shingles or ridge cap shingles will not fail to seal, blow off, or sustain damage from winds (in-cluding gusts) up to the applicable wind speed listed above after they should have sealed but did not due to a manufacturing defect. If your shingles or ridge cap shingles do fail to seal, blow off, or suffer wind damage, GAF will reimburse you for the reasonable costs of replacing the blown-off or damaged shingles or ridge cap shingles and hand-sealing any unsealed shingles or ridge cap shingles. Costs related to underlayment, metal work, and flashings are not included. GAF’s maximum liability under this paragraph is to reimburse you for the cost of hand-sealing all of the shingles and ridge cap shingles on your roof.