The Concord 4 can only be configured with an alpha keypad. From routine run setting: Press 9, understanding code (default is 1234), 030.
What is the system master code for Concord 4 installation manual?
Chapter 3: Programming Concord 4 Installation Manual 87 System master Shortcut: 0320 Default: 1234 The system master code provides access to all system operations and user programming. In the partition where the indicating power device is located, only the system master code may be enabled to disarm that partition.
How do I set up a schedule in Concord 4?
If you are programming schedules for your customer, be sure to record the settings in the Concord 4 User Manual. To set up a time schedule: 1. Press A or B until the display shows SET UP SCHEDULES. 2. Press # and the display shows SCHEDULE 00.
How do I adjust the contrast level on my Concord 4?
Enter configuration mode by pressing the D and 6 buttons together for at least 2 seconds. The display shows DA nnn. Chapter 4: Testing and troubleshooting Concord 4 Installation Manual 103 2. Press and release the 1 and 2 buttons together repeatedly, until the desired contrast level is displayed. 3.
What is the Concord 4 user manual (p/n 466-2183)?
The Concord 4 User Manual (P/N 466-2183) contains user worksheets that you should fill out during the installation and programming of the system. For multiple-partition systems, we suggest a user manual for each partition.
How do I reset my Concord 4?
The light on the smoke detector remains lit until it is reset. Press 1, code again to reset hardwired detectors and clear alarm memory. Note: In some cases, your installer may have installed a smoke detector reset switch. If so, press and hold the switch for at least 1 second, then release it to reset smoke detectors.
How do I get into Concord 4?
To enter program mode on the Concord 4 panel: Press 8, 4321, 0, 0. The display shows SYSTEM PROGRAMMING. Once you have verified that you see SYSTEM PROGRAMMING you can exit programming by selecting the A button followed by # and this point you should be out of programming.
How do you bypass a Concord 4?
Press # + CODE. The keypad will display “BYPASS SENSOR _ _”, enter the sensor you wish to bypass. The keypad will display “BYPASSED ZONE _ _” or “SENSOR _ _ BYPASSED”.
How do you reset a GE security system?
You can reset your alarm system by powering it down and then powering it back on. This is what is known as a power reset. To power down the system, the backup battery must be disconnected, and the transformer must be unplugged. Then reconnect the battery and transformer to power it back on.
How do I get my GE alarm to stop beeping?
Turn off the status beeps on the security alarm system by selecting the menu and going to "Disable TR BEEPS OFF/ON." Press 1 to turn off the beeps. The display will flash to indicate that you turned off the trouble beeps.
How do I put my GE Concord 4 in test mode?
To test your Concord 4 zones/sensors:Place all sensors and zones in their non-alarm state.At an alphanumeric touchpad, enter the sensor test mode by pressing 8, installer code, 3. ... Trip each zone/sensor one at a time. ... Press the Status button when you think all zones/sensors are tested.More items...•
How do I turn off my GE alarm without code?
You can turn off or power down your home alarm system by disconnecting its backup battery and then unplugging the transformer for the device from the wall outlet. You can confirm that the panel has been powered down by checking its touchscreen or keypad and making sure that it is blank.
How do you disarm a Concord panel?
1:502:34Concord 4 How To Arm and Disarm - YouTubeYouTubeStart of suggested clipEnd of suggested clipButton. The system tells you that it's armed in the away mode once again the red armed light isMoreButton. The system tells you that it's armed in the away mode once again the red armed light is flashing. And it will flash during the countdown. You have a predetermined amount of time to exit the
Is it hard to get into Concord College?
Entrance and Exit Entrance to Concord College is highly selective, particularly at the sixth form level – it is truly a place for the most academically-inclined of students.
Is Concord College hard to get into?
Admissions and fees Entry is tough and for entry to Forms 3 and 4, students should have a “strong chance of achieving A* (8s and 9s) or A (7s) grades in a wide range of GCSE Level subjects”. Applicants sit online entry tests or tests at the college and may be required to attend an interview.
What is Concord 4 user manual?
The Concord 4 User Manual (P/N 466-2183) contains user worksheets that you should fill out during the installation and programming of the system. For multiple-partition systems, we suggest a user manual for each partition. Read these instructions and all related documentation entirely before installing or operating this product.
How many smoke detectors can be connected to Zone 8?
When set up for two-wire smoke detectors, zone 8 can handle up to 20 smoke detectors (all of the same model, as listed above) with 120 uA maximum idle current per detector. Maximum total loop current allowed in an alarm condition is 90 mA. Connect one or more, two-wire smoke detectors to the panel as shown in Figure 7 on page 16.
When using two wire smoke detectors on Zone 8?
Note: When using two-wire smoke detectors on zone 8, the two-wire smoke setting (in program mode) must be turned on before entering the learn sensors menu.
