- Lay the Sticker Shield on a clean flat surface with the protective paper side up.
- Lay the EZ Pass transponder on top of the Sticker Shield to mark where to cut it off (about 1/8 inch all around the transponder). ...
- Turn over the piece of Sticker Shield that you cut so the protective paper side is now down.
- The transponder comes with Velcro strips with their own adhesive that you would normally stick onto the windshield, but now you’ll stick them on the shiny side of the piece ...
- Remove the protective paper from the Sticker Shield and you’re ready to go.
- To mount the transponder, remove the transponder from the Velcro strips and place just the Sticker Shield with those strips wherever you want. ...
- Rub the Sticker Shield film firmly to make it smooth and remove any air bubbles. Since it’s carrying the weight of the transponder, make sure it’s attached firmly.
- Finally, press the transponder onto the Velcro strips firmly until it pops.
How to mount or install an EZ Pass correctly?
Jun 17, 2020 · where should EZ Pass be mounted? Position the transponder on the inside of your windshield, behind the rearview mirror and below any tinting. 4. Place the transponder on the windshield with the E-ZPass logo upright, facing you, and press firmly. Fasten the bumper mount transponder directly to the top of the front license plate holder of your vehicle.
How to install EZ TAG on your windshield?
Nov 10, 2021 · How do I get my Ezpass to stick to my windshield? November 10, 2021 Nora Recipe Turn the tag right side up facing you. Place the tag in the correct position and press firmly against the glass for 15 seconds to achieve a good bond. Your E-ZPass tag may be removed by gently lifting one corner of the tag to separate the adhesive strips.
How should you proceed if you lost your EZ Pass?
Jan 17, 2022 · How do I get my Ezpass to stick to my windshield? Flip the label face down towards you. Place the label in the correct position and press firmly on the glass for 15 seconds to ensure a good grip. Your E-ZPass tag can be removed by gently lifting one corner of the tag to separate the adhesive tapes.
How to attach EZ Pass?
The transponder comes with Velcro strips with their own adhesive that you would normally stick onto the windshield, but now you’ll stick them on the shiny side of the piece of Sticker Shield you just cut. Remove the protective film from the Velcro strips, center the transponder over your piece of Sticker Shield, and press it down firmly.
How do I get more Velcro for EZ Pass?
More. Need new adhesive strips? They're FREE! Request them at www.e-zpassny.com or call 1-800-333-TOLL (8655).Jan 28, 2020
Where is the best place to put EZ Pass?
Adhere the tag inside your vehicle to the upper center portion of your windshield, behind the rear view mirror at least one inch to the right of the center support of the mirror and at least one inch below the edge of the windshield, or below the tinted section of glass.
Can EZ Pass be mounted on black dots?
“You only want to mount it on the clear glass. So if you have the roofline tint that goes on the top of the windshield, or dotted tint near the rearview mirror, you don't want to put it on top of that,” says Transurban spokesman Mike McGurk.Jul 11, 2015
How do I remove my EZ Pass transponder from my windshield?
Grip the strip's corner with the needle nose pliers and slowly remove the strip using a rolling motion. Apply WD40 to any remaining residue on your windshield after removing the strips. Make sure to wipe the glass clean.
How do you put an E-ZPass on a windshield in PA?
0:201:33How to Mount or Install an EZ Pass Correctly - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo mount the device place it approximately one inch below the shaded area and one inch to the rightMoreTo mount the device place it approximately one inch below the shaded area and one inch to the right of the rearview mirror. Stick it press and hold for around 5 seconds to secure the glue.
Does I-PASS need to be on windshield?
The important thing to remember is that to receive the discounted I-PASS rate, your transponder must be properly mounted in your vehicle whenever you drive on the Tollway. In most cars, transponders should be mounted on the windshield.
Can I spray paint my EZ Pass black?
Not having the EZ Pass affixed creates safety issues at the toll plaza and the possibility of fines. You can paint yours black but it is messy and still leaves the attachment strips quite visible.Jun 24, 2009
Where does the transponder go on a windshield?
Windshield Mount Locate the correct position for the tag — the upper center portion of your windshield behind the rearview mirror, at least 1 inch to the right of the mirror and at least 1 inch below the top edge of the windshield.
What are the black dots on my windshield?
They use those black enamel outside the windshield to block the sun's ultraviolet rays from melting the adhesive underneath the band. This keeps the windows firmly glued in their place. Third, the black dots, or “dot matrix” actually help distribute temperature evenly to lessen optical distortion or “lensing”.May 15, 2017