How do I reset my Harley Davidson TPS?
- turn big switch off & on 5 times with in 10 seconds.
- With the "kill switch" on the handlebars set to the run position turn the big ignition switch to the run position for 10 seconds and then turn it off ...
- turn big switch 4 times within 10 seconds all the way to accesory.
Full Answer
How do you reset the ECM on a Harley Davidson TPS?
How do I reset my Harley Davidson TPS? You turn theignition on, wait 10 seconds. Then turn theignition off, wait 10 seconds. Do this 4 times and you're done. Click to see full answer. Subsequently, one may also ask, how do you reset the ECM on a Harley Davidson? turn big switch off & on 5 times with in 10 seconds.
How do you reset the throttle on a Harley Davidson motorcycle?
Throttle by Wire High Idle Reset For Harleys if your Harley throttle by wire acts up and high idles when cold starting, dont panic. Try This. To reset your idle setting back turn the ignition switch on for 10 seconds off for 10 seconds (do not start the engine), repeat a total of 4 times. That should reset your original throttle position.
How to reset security system on a Harley Davidsons touring?
Harley Davidson Touring: How to Reset Security System. 1 Step 1 – Turn ignition switch. Turn the ignition switch located on the gas tank to "off," and then turn it to "on." 2 Step 2 – Press both turn signals. 3 Step 3 – Enter security PIN. 4 Step 4 – Discovering the PIN.
How do you change the PIN code on a Harley Davidson?
With a push button fob, press the left turn signal three times, then the key fob twice, and the PIN will appear. Figure 4. Harley Davidson odometer display. This is also the process to change the PIN code, but be sure to write it down somewhere or use a familiar number before you start.
How do you reset the throttle position sensor on a Harley Davidson?
Reset the TPS. Turn ignition switch on for 10 seconds, then off for 10 seconds (Don't start engine). Repeat a total of 4 times. DO NOT TOUCH throttle while doing it.
How do you reset throttle position sensor?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How do I reset my motorcycle TPS?
2:434:11How to Reset the Throttle Position Sensor (TPS) on a 2019 Honda ...YouTubeStart of suggested clipEnd of suggested clipMake sure that you have your kill switch on. And then we're gonna go ahead turn the key wait forMoreMake sure that you have your kill switch on. And then we're gonna go ahead turn the key wait for that mi l and then rip out that jumper connector okay.
How do I manually reset my throttle body?
Make sure that the accelerator pedal is fully released. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds. Turn ignition switch “ON” and wait at least 2 seconds.
How do you reset throttle body after replacing?
Leave the key off for a moment, turn the key to the "On" position again, wait 3 seconds, and press the accelerator 5 times in 5 seconds. Wait 7 seconds, and hold the accelerator down. The check engine light should start blinking, continue to hold pedal down until it stops blinking. You can then start the car.
Can a TPS sensor cause no start?
When a TPS goes bad, then the car's throttle body won't function properly. It could either stay shut or it won't close properly which is a severe issue. If it stays shut then your engine is not going receive air and it won't start.
How do you reset throttle accelerator?
Resetting your electronic throttle control manually can be a tricky job. First, make sure the accelerator pedal is fully released. Next, turn the ignition on and then turn it off and wait for ten seconds. During these ten seconds, be sure the throttle valve is moving by listening for a sound of operation.
How do I reset my motorcycle ECU?
1:022:45How to Reset a Honda Grom ECU - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure that kill switch is in the on position with your free hand you are going to turn theMoreMake sure that kill switch is in the on position with your free hand you are going to turn the throttle all the way open. And very going to flick the key on.
How much is a TPS sensor?
The average replacement cost for the throttle position sensor is anywhere from $110 to $200. The parts cost is anywhere from $75 to $105 while the labor cost is anywhere from $35 to $95.
What happens if you dont reset throttle body?
If the TPS is causing your ECM to think that the throttle is closed when it isn't, it'll reduce the amount of fuel in the air/fuel mixture and cause the engine to run lean. Without enough fuel in the mixture, the engine will fail to make as much power as it normally does.
Does a throttle body need to be calibrated?
Once you have fitted a Throttle Position Sensor, or TPS, you will need to calibrate it from within MEITE. First, be sure you have correctly wired, and assigned the throttle sensor signal input to "TPS Raw" in the Analog Settings.
How do I calibrate my accelerator pedal position sensor?
To calibrate the accelerator pedal assembly: To recalibrate the ECM and accelerator pedal, the ignition switch must be in the ON position and then the accelerator pedal must be slowly and fully depressed from idle to full throttle. Repeat the procedure three times.
How to reset throttle by wire on Harley?
Throttle by Wire High Idle Reset For Harleys. To reset your idle setting back turn the ignition switch on for 10 seconds off for 10 seconds (do not start the engine), repeat a total of 4 times. That should reset your original throttle position. To reset your idle setting back turn the ignition switch on for 10 seconds off for 10 seconds ...
How to reset idle on a Harley?
To reset your idle setting back turn the ignition switch on for 10 seconds off for 10 seconds (do not start the engine), repeat a total of 4 times. That should reset your original throttle position. The throttle by wire will remember throttle position each time the bike is shut down.