How to remove brake drum from wheel?
What happens if you leak brake fluid?
What is drum brake?
How to fix a leaky brake cylinder?
How to replace brake line?
What happens if a car pulls to one side while braking?
How long does it take to replace brake drums?
See 4 more
About this website
How do you disassemble drum brakes?
4:3522:00The ULTIMATE Guide on How to Replace Drum Brakes - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd we're going to hit both sides of the drum. You want to use a good amount of force. And make sureMoreAnd we're going to hit both sides of the drum. You want to use a good amount of force. And make sure you don't hit those studs by mistake. I can feel coming loose. Give it a little wiggle.
How do you unlock rear brake drums?
0:241:33HOW TO REMOVE A STUCK BRAKE DRUM IN MINUTES! - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow if that doesn't work you can use some wd-40 or any kind of penetrating liquid to spray betweenMoreNow if that doesn't work you can use some wd-40 or any kind of penetrating liquid to spray between the axle flange lug nut studs and the drums let it sit for 15 minutes and try the hammer again.
What is the back of a brake drum called?
Backing plate—the plate, attached to the axle assembly, holds the components of the drum brake assembly. A backing plate, as shown in Figure 12-2, is stamped steel and has various holes for springs, parking brake cables, and wheel cylinder attachment, and support pads for the shoes.
How do you remove drum brake screws?
0:052:00Rotor screw removal tip trick when held on with screws for Drums tooYouTubeStart of suggested clipEnd of suggested clipThis is a impact driver it has a Philips bit on it. And you hammer on it and it will take the screwsMoreThis is a impact driver it has a Philips bit on it. And you hammer on it and it will take the screws off so I recommend using this. It's a little practice you can use a hammer.
How do you unlock a back break?
Take your foot off the brake pedal so your wheels can get enough traction to possibly unlock momentarily. Then reapply pressure to the brake if needed. Repeatedly (and quickly) press the brakes over and over until the brakes either disengage or bring you to a safe stop.
What causes drum brakes to not release?
The most common causes of your brakes not releasing is a seized caliper or brake pad. This typically occurs due to rusting or ageing. Typically, you will notice your vehicle pulling to one side when you press down on your brakes.
What are the two purposes of the drum brake backing plate?
They are pressed plates of steel that provide a support for the brake shoes and wheel cylinder. Those components then combine to provide an outward pressure and braking force on the rotating brake drum, slowing the car down.
Are rear drum brakes important?
The drum brakes on a car are an essential part of having maximum braking power. Over time, the drums and shoes on the rear part of a vehicle will have to do a lot of work and may begin to show some signs of wear.
Do drum brakes need brake fluid?
Just like with disc brakes, if there is air in the lines, the brake pedal will feel spongy. In order to bleed drum brakes you will need some fresh brake fluid and a helper.
What tools are needed to change drum brakes?
You'll need a drum brake retainer spring tool and a pair of drum brake spring pliers. These can often be purchased as a set. You'll also need simple tools like a hammer, pliers, and other assorted hand tools to get everything apart.
Do drum brakes have bleeder screws?
Bleeding your drum brakes is the same process as with disc brakes. Start with the wheel that's furthest away from the car's master cylinder and work towards it. You'll find the bleeder screw on the rear of the backing plate, usually near the top.
How do you remove a brake retaining clip?
1:052:04Removing Retaining Clips & Cutting Brake Lines - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you have the clip broken free take a flat blade screwdriver. And wiggle it. Out. Just like soMoreOnce you have the clip broken free take a flat blade screwdriver. And wiggle it. Out. Just like so that's the retaining clip.
Why would a drum brake lock up?
One of the most common causes of one or two wheel lockup on drum brake equipped vehicles is the service and/or parking brake adjustment. If either one or both of these adjustments are done incorrectly it can result in the rear brakes being very sensitive.
What happens if your rear brakes lock up?
When brakes lock up, the vehicle may veer sharply to the left or right, and the back end may fishtail causing the driver to lose control [source: Car Talk]. If this happens while you're driving, pump the brakes consistently until you come to a complete stop, and get the car to a mechanic as soon as possible.
Does drum brakes have anti lock?
ABS has nothing to do with disc / drum brakes , important thing is to have wheel speed sensors on any kind of brake. ABS has nothing to do with disc / drum brakes , important thing is to have wheel speed sensors on any kind of brake.
How do you unlock your parked brakes?
To release a stuck brake you can do several things. If it is safe to do so, you can try rocking the vehicle back and forth or manually getting under the vehicle to pull the cables. You can also try setting and releasing the brake multiple times in the hopes of knocking the brakes free.
How to Remove a Stuck Brake Drum | DoItYourself.com
Step 1 - Block the Car. To get at the brake drums, you will need to raise the back end of the car in the air. Make sure the parking brake lever is fully down before you start any work.
How to adjust a new shoe?
Place the self adjuster on the new shoes and spread the tops apart to tighten the spring. Put the shoes back in place and slip the retaining pins through the right holes. Install the shoe retainer springs. Attach the shoes to the wheel cylinder pins. Reattach the parking brake lever. Install the return springs.
How to remove brake drum?
Grab the brake drum by the edges and pull it off. It may help to wiggle it a bit as you pull. It may be necessary to back off the brake adjuster to remove the drum. This is done through the brake adjustment hole in the drum or on the backing plate using a brake adjuster tool to turn the adjuster to loosen the brakes enough to remove the drum.
How to remove a tire from a car?
Remove the hubcap and loosen the lug nuts. Block the front wheels with wheel chocks. Jack up the car and support it with jack stands. Never work on a car supported by a jack alone. Blocks of wood or bricks or even cinder blocks aren't suitable substitutes. Finish removing the nuts and remove the tire. ...
How to keep brakes from getting dusty?
Place the whole brake mechanism in a container and spray it with brake cleaner. Doing this in a container will help keep the dust from becoming airborne. Remember: the dust from most brakes is asbestos, and you don't want to breathe it in. Wear a mask. ...
How to get rid of brake dust?
1. Put on an asbestos respirator. The work you're about to do involves finely-ground brake dust or asbestos dust, and breathing it can be extremely hazardous to your health. Get a mask that's designed for the job of filtering asbestos, not a simple paper one you might use in a shop.
What is drum brake?
Drum brakes have a bunch of springs and levers for the self-adjuster and parking brake. They are usually different colors. Take a picture with a digital camera or make a detailed drawing of where everything is before you take anything apart!
Why is asbestos used in fire?
Back before people understood that asbestos was harmful, it was used for many things because it is a natural fire retardant and it handles heat very well.
What does it mean when your brake drum is stuck?
A stuck brake drum is just one of the many issues that you may run into if you are performing your own maintenance and repairs on your vehicle. Thankfully, Vehicle History provides a wealth of information regarding the maintenance of every make and model in existence, enabling you to access the information about your vehicle ...
How to remove rust from brake drum?
If you still aren’t able to remove the brake drum, you will need to cut or drill out the holding pins from the drum, remove the screws to the brake cylinder, and pull off the drum.
What to do if your brakes are stuck?
If your brakes are stuck open, they will hold the brake drum in place no matter how hard you try to remove it, making removing the holding pins the only option you have for getting the brake drum off. Once these holding pins are removed, though, you should be able to remove the screws from the brake cylinder and pull off ...
How to remove a drum from a sandbox?
Remove the rubber grommet which will give us access to adjust the automatic adjuster. Two screwdrivers are needed, insert the first screwdriver into the hole, push back the lock. Take the standard screwdriver and rotate the star wheel. Finally you can remove the drum.
How to use a ball peen hammer?
Using a ball peen hammer, hit the drum between the wheel studs where the hub face is located. Go around the perimeter between each of the studs, being careful not to hit any of the studs as you can damage the threads. If you are worried about accidentally hitting the wheel studs, either install the lug nuts or place a rubber hose over top of the studs. Heat can be applied to the mounting surface either using a propane or acetylene torch set. NEVER hit outside of the hub area, on the outer edge where the cooling fines are, or on the back edge of the drum. Doing so will greatly risk the chance of damaging the drum’s casting, either resulting in a crack or chip making the drum unsafe to use.
What happens if you can't rotate the drum?
Now on the other hand, if you cannot rotate the drum, then the pads are engaged either by rust, stuck wheel cylinder, or stuck parking brake. Tools/Supplies Needed:
Why is my parking brake stuck?
To determine if it is stuck, operate the lever inside the vehicle and you should feel loose travel before tension is applied. Another reason for that loose travel is if your parking brake is out of adjustment. The cable will need to be replace even if you are able to get it loose as it can occur again. First try giggling the cable, adjusting it, and if that fails, then cut it directly behind the drum brake assembly as close as possible. The parking brake lever inside the drum assembly will release and allow the shoes to retract.
How to fold shoes in drum?
Start by clipping the hold down pins on the backside. Once done, this will allow you to fold the shoes within the drum. Try pulling back by hand or with the assistance of a puller. If that fails, then remove the wheel cylinder where the fasteners can be access from the backside of the backing plate.
How to remove brake drum from wheel?
Draw the brake drum forcefully towards you. Use a screwdriver and rubber mallet or a brake drum puller to take the drum off of the wheel if you are unable to remove the drum by unscrewing it and pulling it.
What happens if you leak brake fluid?
If there is a leak in the hydraulic system, you may notice fluid inside the drum and on the brake shoes. Usually, this is accompanied by decreased brake performance. If necessary, replace the leaky wheel cylinder.
What is drum brake?
Drum brakes (as opposed to disc brakes) are a braking system that slows a vehicle by pressing brake shoes into the inside surface of a metal drum attached to the wheel to create friction. Like any braking system, drum brakes undergo wear and tear with use. Brake drum maintenance and replacement requires that you first remove ...
How to fix a leaky brake cylinder?
If necessary, replace the leaky wheel cylinder. Loosen the brake line connected to it, then loosen the bolts at the rear of the cylinder. Insert the new cylinder into its proper place, attach the brake fitting, then the brake line, then finally re-screw the bolts. Inspect the brake lines for damage.
How to replace brake line?
To replace damaged brake lines ,you'll first need to loosen and remove the old brake line at its fittings with a flare nut or wrench cap. Be sure to cap the line to prevent spilling any fluid if necessary. Then, cut a new length of brake line and mate it to the old line with brass connectors or simply install it directly into the old line's fittings.
What happens if a car pulls to one side while braking?
As a common rule of thumb, if the car pulls to one side while braking and the brake caliper appears undamaged, you may have a leak in your brake line. To replace damaged brake lines ,you'll first need to loosen and remove the old brake line at its fittings with a flare nut or wrench cap.
How long does it take to replace brake drums?
This procedure is usually fairly simple, requiring no more than a half hour or so and common vehicle maintenance tools. Steps.
