Whirlpool Ice Maker Not Working
- 1. Check the power supply. Make sure the power cord is plugged into a good outlet. Also check if the outlet is grounded.
- 2. Check the fuse box. It could be blown.
- 3. Check the circuit breake r. It could be tripped.
- 4. Check the faucet. Is the water running properly?
- 5. Check the drain hose. Is it clogged?
Full Answer
How to reset a whirlpool icemaker?
So, follow these 11 steps to reset the whirlpool ice maker the right way in a short period of time:
- Unplug The Power Source: Firstly you have to unplug the ice maker from its power source. ...
- Remove The External Wires: Now you have to remove any wire harnesses that connect to the appliance from its back. ...
- Remove The Remaining Ice Cubes: Remove all cubes and put them in a freezer bag or container for later use. ...
How to fix a whirlpool ice maker?
Why Whirlpool Ice Maker Not Working – Troubleshoot and Diagnosis
- Ice Maker is OFF. Any Whirlpool freezer with a built-in ice maker will have a push button. ...
- Freezer Temperature Issue. It’s best to maintain your ice maker between 0-5°F. ...
- Jammed Ice Maker. ...
- Clogged/Frozen Water Line. ...
- Defective Water Filter. ...
- Check Water Inlet valve. ...
- Faulty Icemaker Mold Thermostat. ...
How do you troubleshoot an ice maker?
- Test the water inlet valve
- Flush out the supply line
- Clean the ice mold tray
- Install a supply line filter if your fridge doesn't already have one
Why is my Whirlpool fridge ice maker not working?
- One of the most popular reasons is when the control arm is out of position and activates the pause feature. ...
- Another issue may be that your water line is clogged or turned off. ...
- Make sure that the filters are not clogged. ...
- Do not forget to check the water inlet valve which may be broken and hence the ice maker is not operating. ...
How long does it take to reset an ice maker?
How to open a freezer door?
How to change the LED light on a freezer?
When did Whirlpool redesigned the optics?
Is Whirlpool in door ice maker good?
Why did my Whirlpool ice maker stop making ice?
Cause: Your filter works hard to help reduce contaminants in your water, but can become clogged with particles it may trap over time. A clogged filter can send less water to the ice maker, which may cause a decrease or halt in ice production.
How do I reset my Whirlpool ice maker?
The reset button is usually located at the bottom of the ice maker unit or in some cases at the top or on the bottom of the ice tray. Once located, press the button down for a few seconds until you hear a beep sound. Once you hear the beep sound, let go of the button. Once reset, check if the problem has been solved.
Why is my Whirlpool side by side refrigerator not making ice?
Make sure the water supply is properly connected to a cold water supply and the water shutoff valve is fully opened. Check to make sure there are no kinks in the water supply line. A kink in the line can reduce water flow. Straighten the water source line to restore adequate water flow and pressure.
How do I manually reset my ice maker?
First, remove the ice bucket and the covering from the front of the ice maker. Some models have a button you will need to push to remove the ice tray and cover. Others will just require you to pull it off. Once the ice tray and covering have been removed, locate and press the ice maker reset button for about 3 seconds.
Why would an ice maker suddenly stop working?
What causes an ice maker to stop working? There are several reasons you may find your ice maker not working all of a sudden, including a blocked water dispenser, issues with your water supply line, or a clogged water filter.
Why is my ice maker not making ice but water works?
If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
How do I get my Whirlpool refrigerator to make ice?
0:041:08How to turn ice maker on & off on a Whirlpool French door refrigeratorYouTubeStart of suggested clipEnd of suggested clipThe indoor ice maker is located at the top of the refrigerator. Compartment on the left. Side iceMoreThe indoor ice maker is located at the top of the refrigerator. Compartment on the left. Side ice cubes are made. And then ejected into the ice bin located in the left.
Is there a reset button on Whirlpool refrigerator?
There's a reset button on some Whirlpool refrigerators, but it's exclusively for the ice maker. You have to unplug your appliance for 5 to 10 minutes to reset the fridge. You can also reset it by pressing the door switch and temperature plus (+) button 3 times in 10 seconds.
Where is the reset button on my ice maker?
You can find the reset button at the bottom of the ice maker. Remove the ice tray to locate it. Remove the ice tray. The red button you see is the reset button.
How do I get my ice maker to work again?
Turn The Ice Maker Off and On Again If your ice maker has a switch other than the control arm, find it and toggle it. This is a simple matter of resetting the power to your ice maker. By flipping the switch off and back on, you may be able to reset the functionality so that your ice maker begins to dispense ice again.
How do I reset the feeler arm on my Whirlpool ice maker?
Press the reset button – usually located near the ice maker. If that doesn't work, adjust the feeler arm, turn it off and on again, or unplug it for five minutes.
Why is my Whirlpool French door refrigerator not making ice?
What it Does: A common cause for a Whirlpool ice maker not working is jammed ice crusher blades. If your refrigerator has a crushed ice option, then its dispenser system will have these blades. How to Fix it: Check the blades to see if they are jammed with ice. If so, pour warm water over them until the ice melts.
Where is the reset button on my ice maker?
You can find the reset button at the bottom of the ice maker. Remove the ice tray to locate it. Remove the ice tray. The red button you see is the reset button.
Where is the reset button on a Whirlpool refrigerator?
Locate the reset button on the bottom of the ice maker. Press and hold the reset button for about ten seconds. Once you hear a chime (or the ice maker turning on again), let go of the button. If your unit doesn't have a reset button, find the on/off switch and turn the machine off.
How do I force my ice maker to cycle?
Turn The Ice Maker Off and On Again If your ice maker has a switch other than the control arm, find it and toggle it. This is a simple matter of resetting the power to your ice maker. By flipping the switch off and back on, you may be able to reset the functionality so that your ice maker begins to dispense ice again.
How do I reset the feeler arm on my Whirlpool ice maker?
Press the reset button – usually located near the ice maker. If that doesn't work, adjust the feeler arm, turn it off and on again, or unplug it for five minutes.
What are some common ice maker problems and solutions?
Refrigerator ice maker problems can often be tied back to a handful of main components, including water valves and lines, the water filter, the ice...
Ice maker is not working or not making enough ice
An ice maker that doesn’t produce can feel like nothing more than a waste of precious refrigerator or freezer space. Browse some of the common caus...
Ice maker is making ice, but is not dispensing
A dispenser refusing to release cubes into your cup can be frustrating, especially when the ice bin is visibly full. Some of the most common causes...
The ice maker is making too much ice
Ice makers control ams are designed to sense a full ice bin and pause ice production at the right times, so an overflowing ice bin can be a sign th...
The ice has an odd taste
Strange-tasting ice in your favorite drink can be an unpleasant surprise, and may leave you wondering what’s wrong with your ice maker. Some common...
The ice maker is leaking
A leaky ice maker might drip into the ice bin and may cause ice clumps to form, or leak outside of the refrigerator or freezer and create a puddled...
The ice maker is making ice cubes that are too small
Ice cubes that are hollow or too small can usually be traced back to two main factors: water flow and temperature settings in the refrigerator or f...
The ice maker itself is frozen
Determining the cause of a frozen ice maker can seem complicated when you have large chunks of ice blocking your line of sight. Luckily, the common...
6 Reasons Why Whirlpool Ice Maker Not Working – Let’s Fix It - KCSCFM
1. Ice Maker is OFF. Any Whirlpool freezer with a built-in ice maker will have a push button. This button turns the ice maker on and off, and this is usually located behind the front panel of your refrigerator. The wire arm attached to your ice maker should be pushed up to turn the ice maker OFF and lowered to turn it ON.
How to Reset Your Whirlpool Ice Maker | Better Home + Living
I’m glad that you checked out Better Home + Living today! We are a lifestyle blog that helps our readers find value in their home and life. We've been writing informational, reviews and helpful articles for a very long time, and have grown into a trusted source for home + living.
Why Is My Whirlpool Ice maker Not Making Ice? [SOLVED] – Let ... - KCSCFM
It’s not too early to start thinking about summer again. So if you find your Whirlpool Ice maker not making ice, it’s time for some quick troubleshooting before it gets too hot.Make sure the ice maker is turned on and then check the water supply.
How long does it take to reset an ice maker?
If you don’t get any response from the diagnostic test… wait 5 minutes then unplug the refrigerator for 10 seconds to reset the ice maker control board and try again.
How to open a freezer door?
Step 2. Activate the door switch 3 times. Push the button in completely for 1 second each time. Step 3. Close the freezer door for a minimum of 5 seconds for a maximum of 50 seconds. Step 4.
How to change the LED light on a freezer?
Step 1. Open the freezer door and observe the red status light next to the ice maker’s on/off switch. Result: You should see two flashes and a one second delay repeating. If there is no light your LED light may be out, you may have pre 2002 boards installed, or the optics boards need to be replaced. Step 2.
When did Whirlpool redesigned the optics?
One other important note… Whirlpool redesigned the optics portion of this system around 2002 so there are two different diagnostic methods depending on which set of boards are installed in your refrigerator, pre or post 2002 ice maker models.
Is Whirlpool in door ice maker good?
The Whirlpool & Kitchen Aid in-door ice system is very nice design because it frees up a large amount of space in the freezer compartment and makes important job of dumping old ice much more convenient. Mechanically, this is a Whirlpool modular ice maker with a few extra trim pieces, different fill tube location, and a set of control boards have replaced the bail arm switch.
Why is my ice maker not working?
The typical cause for malfunction is a clog in the supply line. Although there are many different types of clogs that could occur, one of the most common problems comes from ice that has frozen solid at some point along the supply chain.
Why does my ice maker make noise?
When your ice machine is making noise and the ice cubes are jamming up , this could be a sign that you need to replace your water filter. If you don’t change the filter every six months or so, sediment and other particles may build up in the ice machine and make it stop working; while a dirty water filter will leave bad-tasting water behind when you try to make drinks with the dispenser.
Why is my freezer not cold enough?
One may be that your refrigerator’s condenser coils are dirty which prevents the fan from cooling them down. To clean the condenser coils, unplug your refrigerator and remove all items from the freezer .
What is an ice maker mold thermostat?
An ice maker mold thermostat is a small device installed in the ice maker of older refrigerator models. The thermostat regulates the temperature of the ice mold, or tray so that it can efficiently freeze water into cubes.
How hot should my ice maker be?
It’s best to maintain your ice maker between 0-5°F. As the temperature of the freezer goes up, your ice maker will either produce less ice or jam entirely. If you are consistently getting less than one tray per day, the temperature may be too high.
What is the inlet water valve on a refrigerator?
An inlet water valve is responsible for supplying water to the refrigerator’s ice maker. If there isn’t enough water pressure entering the valve, it can’t open sufficiently to allow water to flow through. That means the ice maker will shut down and you’ll be without ice. If you want to ensure your ice maker keeps producing, have the problem fixed as soon as possible.
How to defrost water line in refrigerator?
A turkey baster is a great way to defrost a refrigerator water line. However, it can be difficult to tell when the line is defrosted. A nice workaround is to use a hair dryer on a low heat setting, or to leave the refrigerator unplugged overnight or for a couple of hours. It’s also a good idea to verify that the water line is moving water by watching it carefully as you use the hair dryer.
Why won't my Whirlpool ice maker work?
Your Whirlpool ice maker may not work when the water dispenser does if the shut-off arm is in the wrong position. Switch the shut-off arm to the ON position and inspect the water filter for debris. A bad door switch or water inlet valve can also cause a Whirlpool ice maker to not work.
How to reset Whirlpool ice maker?
Just follow these steps. Step 1: First, you will need to locate the reset button. If you have trouble finding it, check your user’s manual for the location.
What Would Cause My Ice Maker to Stop Working?
Many things could cause your ice maker to stop working. This might stump you if the water dispenser is still working. Thankfully, most of the problems are easy to fix.
How long do you have to unplug a Whirlpool refrigerator?
Step 4: Old Whirlpool ice makers do not have a reset button or an on-off switch. In this case, you will need to unplug your refrigerator for 30 seconds.
How to know if your freezer is frozen?
First, check to make sure that the temperature of your freezer is set to 0 degrees or 5 degrees. A sign that your freezer is not set low enough, could be that the food is not all the way frozen. You can test this by feeling the food inside of your freezer to make sure it is frozen solid.
What happens if your water filter goes bad?
Don’t worry, this is an easy fix. If the water filter goes bad or clogs, it restricts the water going to the ice maker. Your water dispenser will still dispense water but at a lower flow.
What happens if the door switch on a refrigerator fails?
Freezers and refrigerators have a door switch. The door switch turns off the ice maker when the door is open. If the switch fails, the ice maker will not work. If you think your door switch may not be working properly, you will need to test it.
How long does it take to reset an ice maker?
If you don’t get any response from the diagnostic test… wait 5 minutes then unplug the refrigerator for 10 seconds to reset the ice maker control board and try again.
How to open a freezer door?
Step 2. Activate the door switch 3 times. Push the button in completely for 1 second each time. Step 3. Close the freezer door for a minimum of 5 seconds for a maximum of 50 seconds. Step 4.
How to change the LED light on a freezer?
Step 1. Open the freezer door and observe the red status light next to the ice maker’s on/off switch. Result: You should see two flashes and a one second delay repeating. If there is no light your LED light may be out, you may have pre 2002 boards installed, or the optics boards need to be replaced. Step 2.
When did Whirlpool redesigned the optics?
One other important note… Whirlpool redesigned the optics portion of this system around 2002 so there are two different diagnostic methods depending on which set of boards are installed in your refrigerator, pre or post 2002 ice maker models.
Is Whirlpool in door ice maker good?
The Whirlpool & Kitchen Aid in-door ice system is very nice design because it frees up a large amount of space in the freezer compartment and makes important job of dumping old ice much more convenient. Mechanically, this is a Whirlpool modular ice maker with a few extra trim pieces, different fill tube location, and a set of control boards have replaced the bail arm switch.
