Hunter controllers allow you to start a station or an entire program manually. To do so, turn the dial to Manual Single Station or Manual All Stations, verify that the stations that you want to activate have run time, and turn the dial back to the Run position.
How do you turn on a hunter sprinkler system?
We’re providing the step-by-step procedure to turn on properly a Hunter sprinkler system below. Just match your steps with it. The monitor at the top left shows time. Check carefully whether the time is correct and accurately matches with the time at the watch. If it doesn’t, then reset the time matching with the current time.
How does the Hunter smart irrigation controller work?
The Hunter system offers a unique advantage, thanks to its innovative Smart Irrigation controller features. You can easily control and automate your sprinklers through the control system for automatic turn-on and shut-off, as well as scheduled watering times. This is based on the Hunter Run Time Calculator. What is the Hunter Run Time Calculator?
How do I program my Hunter controller?
How do I program my controller? Hunter controllers allow you to start a station or an entire program manually. To do so, turn the dial to Manual Single Station or Manual All Stations, verify that the stations that you want to activate have run time, and turn the dial back to the Run position.
How do you turn off the water to a sprinkler system?
Slowly open the main shutoff valve to let water into the sprinkler system. For a ball valve, turn the lever handle one-quarter turn until the handle is parallel to the pipe; this is the fully open position. For an in-ground shutoff valve, use a sprinkler valve key to turn the valve counterclockwise until it stops.
How do I turn on my hunter irrigation system after winter?
Spring Start-Up ChecklistOpen the system main water valve slowly to allow pipes to fill with water gradually. ... Verify the proper operation of each station valve by manually activating all zones from the controller.Walk through each station on the controller, checking for proper operation of the zone.More items...
Why is my hunter sprinkler system not turning on?
If the sprinklers do not turn on you may have a valve shut down that supplies the irrigation system. If the sprinklers come on, you may have a wiring problem at the valves. Check the wiring connections at the valves for loose or corroded connections.
How do I turn my hunter node back on?
To put the Node battery powered sprinkler timer in the off mode, use the center button to advance to the off screen and allow the controller to go to sleep in that position. To turn the controller back on, use the center button to return to the home screen and allow the controller to go to sleep in that position.
How do you manually run a hunter sprinkler?
Manual Run – All StationsPress and hold the button for three seconds. ... Select program by pressing the button.Use the or buttons to select the amount of time for the station to water if different from the run time displayed.Use the button to move to the next station.
Why won't my sprinkler system turn on manually?
Here are some common reasons why your sprinkler system won't turn on: Lawn sprinkler control timer isn't working correctly. Clogged or dirty sprinkler heads. Broken sprinkler heads.
How do you manually turn on a sprinkler valve?
0:171:00Manual operation of Rain Bird valves - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the solenoid in the on or counterclockwise. Direction about a quarter turn then wait a fewMoreTurn the solenoid in the on or counterclockwise. Direction about a quarter turn then wait a few seconds until you hear water rushing through the valve.
How do I manually turn on Hunter node?
0:061:13Manually run a Hunter NODE irrigation controller - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust hold down this play button until that hand appears. And that runtime appears and the system'sMoreJust hold down this play button until that hand appears. And that runtime appears and the system's going to count down.
How do you turn off Hunter irrigation?
0:090:47X-Core® system OFF - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply return the dial to the run position. Once the dial is back in the run position then theMoreSimply return the dial to the run position. Once the dial is back in the run position then the controller will resume the normal programs at the next scheduled start.
How do you turn off a hunter node sprinkler?
0:090:49NODE: Off mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse the center button to advance to the off.MoreUse the center button to advance to the off.
How do I turn on my hunter sprinkler system in the spring?
0:475:37Spring Sprinkler Activation + Start Up - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo a first step that we'll want to do is we want to shut that drain off and then we'll want toMoreSo a first step that we'll want to do is we want to shut that drain off and then we'll want to slowly. Press your eyes the balls out here and you'll hear it start to kick on.
How do I reset my hunter sprinkler system?
Press and hold the Programs button, and at the same time press in the recessed Reset button with the tip of a ballpoint pen. Release the Reset button and continue holding the Programs button until the Reset Memory screen appears (then release the Programs button).
How do you test a hunter solenoid?
0:232:53Troubleshooting a Hunter Valve that is not Opening - Quick Tip - YouTubeYouTubeStart of suggested clipEnd of suggested clipWays. You can open the solenoid a quarter turn does the water flow. Through if it does then we knowMoreWays. You can open the solenoid a quarter turn does the water flow. Through if it does then we know we're probably looking at a electrical issue of the power not making it to the valve.
Why is one sprinkler zone not working?
If only one zone isn't working, the field wire is damaged. If none of the zones in a control valve box is working, the common wire is damaged, although the field wires could also be bad.
When to turn on Hunter irrigation system?
When spring arrives and freezing temperatures cease , it's time to turn on irrigation systems and start watering again. However, when you do so, you should take a few very important steps to make sure you do not damage pipes or irrigation components. It is always best to hire a professional contractor. We have provided a spring start-up guide below to help ensure your Hunter system is up and running with ease and efficiency.
How to get connected with an irrigation professional?
To get connected with an irrigation professional, use our Professional Contractor Referral Form. We will put you in touch with a qualified professional near you that will ensure your Spring Start-Up is properly completed.
Why do you need to spring clean your irrigation system?
Spring cleaning your irrigation system prolongs life and improves watering efficiency, saving time, water and money. When spring arrives and freezing temperatures cease, it's time to turn on irrigation systems and start watering again.
Why do sprinkler lines crack?
Open the system main water valve slowly to allow pipes to fill with water gradually. If these valves are opened too quickly, sprinkler main lines are subjected to high surge pressures, uncontrolled flow and water hammer , which may cause them to crack or burst.
How To Turn On Hunter Sprinkler System?
Are you sure that you turned on your Hunter sprinkler system properly? Why don’t you just check again to find out if you missed out on any important step? Hey, let’s help you out!
What to do if sprinkler doesn't turn on?
Therefore, if a particular sprinkler doesn’t turn on, then try removing the head, cleaning it well, and re-insert it in its place. Does it turn on now?
Why won't my sprinkler system turn on?
Below mentioned are a few of the reasons why a sprinkler system won’t turn on: Clogged Sprinkler Heads. Sprinkler heads getting clogged and filled with dirt isn’t something unusual to happen. Sprinklers remain within the soil and sprinkles water.
Why is my sprinkler system not working?
Did you forget to check whether the pipes connected to the sprinkler system contain any leaks? This can be the most probable reason for your sprinkler system not to work.
What does setting the run time on a sprinkler mean?
Setting the run time indicates the amount of time your sprinkler will remain on before it automatically shuts off.
Why is a sprinkler valve important?
Valves play a more important role than you think. A malfunction within the valve will cause the whole sprinkler system to disfunction. So, you need to make sure if your valve is working properly and isn’t defective.
Is it bad to have a sprinkler system in your lawn?
You are at the right place. When it comes to keeping your lawn fresh and well-managed, nothing beats the role of a sprinkler system. But the condition of your lawn will be in danger if the sprinkler system is not working in all zones too.
How to use Hunter controller?
To do so, turn the dial to Manual Single Station or Manual All Stations, verify that the stations that you want to activate have run time, and turn the dial back to the Run position. When the station or stations finish watering the controller will go back to normal automatic operation.
Where to find owner's manual on Hunter controller?
Other documentation can be found in the Hunter Resource Library. Click here to view all Controllers owner's manuals.
Why does my sprinkler light flash?
The sprinkler icon flashes when the controller is outputting power to the station terminal or terminals activating a station. If the icon is blinking with an umbrella on the display, as in the SVC, the rain sensor's circuit has been broken and is not allowing for watering even though scheduled watering should be occurring.
How to tell if a controller is hardwired?
The controller is running on the power supplied by the backup battery. Check the power source by plugging a lamp or radio into the wall outlet to verify there is power at the outlet. If your controller is not plugged into a wall outlet, the power source is hardwired.
Why does my Hunter controller cycle more than once?
The most common reason for systems to cycle more than once is having programmed too many Start Times. Hunter controllers allow you to setup multiple Start Times to run programs more than once a day. At each Start Time the controller will cycle through all the Station Run Times on that given program.
What is seasonal adjust?
Seasonal Adjust is used to make global run time changes without re-programming the entire controller. This feature is perfect for making small changes that are necessary as the weather changes. For instance, during hotter times of the year, the landscape may require a bit more water. Seasonal adjust can be increased so that the stations will run longer than programmed time. Conversely, as fall approaches, the seasonal adjust can be reduced to allow for short watering durations.
How to move out of interval mode?
To move out of the Interval mode and back into one of your other two options simply continue pressing the right or left arrows. Eventually you should see either a drop of water above the individual days or a drop with a circle around it and a line through it. Now you are in Day of the Week mode and the days of activation will need to be chosen.
How to shut off a valve?
To shut off the valve, twist the solenoid clockwise until it is snug on the valve. If playback doesn't begin shortly, try restarting your device.
How to clean a diaphragm?
The diaphragm should be clean and free of wrinkles, tears, or perforations. The seal should be clean and free of nicks, dents or abrasions. Wash the diaphragm with clean fresh water to remove any debris that may have been deposited there.
How to fix a valve that is still open?
To fix this, you'll need to disassemble the valve, rinse all the parts with clean water, and re-assemble the valve. If you cannot locate your valve boxes or fix the valve, it is recommended you contact the contractor who installed the system, or use our Professional Contractor Referral page to help find a professional contractor in your area.
How to turn on sprinkler system?
This can burst fittings or pop off sprinkler heads. Always open the system shutoff valve slowly to let the system pressurize gradually; it takes just a few seconds.
Where is the sprinkler system shut off valve?
If there is no sprinkler system shutoff inside the home, look inside the sprinkler system valve boxes around the yard. The shutoff valve has a cross-shaped handle and may be well below ground level, inside a ground box or large pipe.
Where is the main shut off valve located?
If you don't know where your system's shutoff valve is located, look in your basement or crawl space for piping coming in near ground level. The piping should include a single shutoff valve, usually a ball valve with a lever-type handle.
How to bypass rain sensor circuit?
Solution - Slide the Rain Sensor switch on front panel to the BYPASS position to bypass rain sensor circuit, or install the sensor jumper.
Does the controller have a start time?
Controller does not have a start time for each station.
