how do you build a deck railing for a planter box

How to Make a Deck Rail Planter

Full Answer

How do you build a deck railing on a planter box?

How to Make a Deck Rail PlanterMeasure and cut wood to length. Measure out and mark each board with a square before cutting. ... Build the box. ... Trim the box. ... Drill drainage holes. ... Sand and clean. ... Seal.

How do you attach a planter box to a deck?

Screw Attachment You can screw through the bottom of a flower box to attach the box to the top of a railing or screw through a flower box's side to attach the box to the side of a railing. Pilot holes drilled in the desired area before installation makes it much easier to drive the screws into place.

How do I build a deck railing?

0:022:12How to Build & Install Deck Railings - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe recommend that you don't notch your rail posts rail post should be spaced no further than sixMoreWe recommend that you don't notch your rail posts rail post should be spaced no further than six feet apart. Use two half-inch carriage bolts to attach each post to the rim board.

Do railing planters need drainage holes?

If your Railing Planter will be exposed to rain, you will need to open the drainage holes to allow excess water to drain.

What do you put under planters on a deck?

Pot feet and risers work much like the legs of a chair, raising the pot off of the ground. By simply positioning them beneath your planter or saucer, you reduce the amount of contact between your planter and the decking and allow airflow beneath your containers.

Can you put a garden box on a deck?

The long answer is yes, but there are two main factors to consider before placing a raised garden bed on a timber deck: weight and water.

What can I use instead of a deck railing?

Consider stainless-steel cables, metal tubes, or composite railings if you're looking for low-maintenance alternative to wood balusters and railings for your deck.

How do you make a simple outdoor railing?

0:217:02How to make deck / porch railing easy with just 2x4's DIY Home ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipI want my relaying to be 36 inches above the step. So I'm going to use a four foot 2x4. And cut thatMoreI want my relaying to be 36 inches above the step. So I'm going to use a four foot 2x4. And cut that to the perfect size later on. So I'm going to install the 2x4. At the beginning of the second step.

What is the most inexpensive deck railing?

What is the most inexpensive deck railing? Typically, pressure-treated lumber (wood) is the cheapest deck railing material, though vinyl (PVC), polyurethane, and composite materials all make for affordable deck railing.

How do I choose a railing for my planter?

The first thing to take into account for railing planters is the width of your deck or balcony's railing. Several are made to set into wood that measures 2 x 4 or 2 x 6 inches, while others are adjustable, which is handy. If neither option works for you, your best bet is to choose one with hooks.

What do you put in a planter railing?

Small flowers such as bright marigold flowers, pansies, blooming petunias in pots, dwarf zinnia, geraniums, and the like all flourish in railing planters.

What do you put in the bottom of a planter for drainage?

Perlite is a soil amendment that improves drainage and encourages root growth. It can also help keep the soil from getting compacted in a container. Some potting soil already includes perlite, but it can be purchased separately and then mixed into soil.

How do you secure a planter on a balcony?

Tie The Plant Pots To Something Sturdy After the hole has been drilled, you can put a zip tie, small rope, or iron wire through the hole and tie the plant pot to the balcony railing. This is one of the easiest ways to protect your potted balcony plants from tipping over by the wind.

How do you attach a planter to a balcony?

How to Hang Planters on Balcony RailingsChoose hanging brackets that fit your railing width and the bottom of your planters. ... Place the planter in the bracket. ... Drill holes into the planter where you marked.Place the planter back on the bracket and attach using screws and nuts through the holes you drilled.More items...

How do you attach a flower box to a balcony?

Drill holes in the wood and insert plastic wall anchors into each hole for added strength. Place the holes one inch from the top of the box at six inch intervals horizontally. Screw the hooks into the wall anchors with the open part of the hook facing down. Hang the flower box on the top rail of the balcony.

How do you put plants on a deck?

0:002:05How to Decorate a Deck or Patio with Flowers - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut one single container can feel kind of lonely plant multiples of the same container or plantMoreBut one single container can feel kind of lonely plant multiples of the same container or plant various sizes to perk up your patio with color really pack them in tight with annuals.

How to make a planter with a planter board?

Measure out and mark each board with a square before cutting. Cut the 48″ 1″ x 2″ boards first. Then cut the 1″ x 6″ planter bottom and 1″ x 8″ planter sides. Follow with the 5-1/2″ 1″ x 8″ and 7″ 1″ x 2″ pieces , being careful to dry-fit everything as you go, making adjustments as necessary.

How to make a planter with a 5 1/2" side board?

Place a thin bead of construction adhesive on the end of the 1″ x 6″ planter bottom and secure a 5-1/2” side board with three nails. Repeat on the other side. (Warning: Woodworking adhesive is very sticky and difficult to remove, so be careful and clean your work as you go.)

How thick is a 1x6 board?

Note: In general, a 1″ board is in actuality 3/4″ thick. And a 1″ x 6′ board is in actuality 5-1/2″ wide. However, some 1″ x 6″ boards are 5-3/4″ wide instead of 5-1/2″. So be careful to measure when buying and as always, measure twice and cut once in the shop.

DIY Railing Planter Box

Hey guys! I’m working with the Kreg Tool company to create another project for Build Something, which is Kreg’s DIY project plan website. I made a workbench for my last project, and this time around I’m sharing the free plans for a DIY railing planter box. Isn’t she a beaut?

If you like this project, you might also like these

DIY Hanging Indoor Garden: This DIY hanging indoor garden will help you display your plants in a beautiful way, especially if you’re short on space.

How thick should a bottom brace be for a planter?

Editor's Tip: The bottom brace should be thick enough that it touches the spindles that attach to the railing so the planter rests snug against the spindles. In our case, the 1/2 inch cedar board was a perfect fit. Depending on the width of your railing, this may need to be adjusted.

How to use cedar board for planters?

Use it to cut two boards that are the same length as the planters. Add a brace to the back, bottom edge of each planter using wood screws.

Assemble and mount this simple planter in less than an hour

Make a simple railing-mounted planter from standard gutter parts. You can complete it in an hour for less than $15.

Assemble a rail-mounted planter

Cut a 2-ft. length of vinyl gutter and glue one of the end caps into place with kitchen and bath adhesive caulk. Drill 1/2-in. drainage holes every 4 in. along the bottom of the gutter.

Required Tools for this Project

Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.

Required Materials for this Project

Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.

How to Build a DIY Planter Box

It’s as simple as putting a box together from wood boards and screws. It’s the basic DIY woodworking project. There are two important things for container gardening – soil and water drainage.

Easy Planter Box Ideas

I’m an avid DIYer, but I am also a bit lazy. So if I can skip a step in a project by reusing something – I will. This counts as recycling, doesn’t it?