How to Replace an Office Chair Cylinder
- Step 1 Tip the chair onto its side.
- Step 2 Use the rubber mallet to tap the base of the chair away from the seat of the chair. ...
- Step 3 The cylinder will be exposed. ...
- Step 4 Now that the hydraulic cylinder has been removed, you can replace it with the new one. ...
- Step 5 ...
How to replace the piston in an office chair?
- Slide the plastic skirt off the cylinder. Most office chairs have a plastic tube over the extendable cylinder.
- Set the chair to the preferred height.
- Wrap a hose clamp around the cylinder.
- Improve the grip of the clamp (recommended).
- Tighten the clamp as far as possible.
- Test the chair.
How often should you replace an office chair?
How often you need to replace an office chair depends on the quality of the chair and how often you sit in it. Higher quality chairs and ergonomic office chairs can be replaced every 10 years, whereas lower quality office chairs need to be replaced every five years. Donate old chairs to local thrift stores or organizations like The Furniture ...
How to fix a hydraulic office chair?
Method 2 Method 2 of 2: Using PVC Pipe
- Measure your chair's cylinder. Pull down the plastic skirt cover the extendable, metal cylinder. ...
- Buy a length of PVC pipe. This pipe will fit over the pneumatic cylinder of the chair. ...
- Saw through the PVC pipe lengthwise. Secure the pipe in a vise. ...
- Snap the pipe onto the chair cylinder. ...
- Add more pipe to adjust the height of the chair. ...
How to reupholster an old office chair?
- The new fabric: Simple, cotton-based fabrics work best for these upholstering projects. ...
- A screwdriver set: If you have an electric drill or similar device that you can use as a screwdriver, this will work even better for a DIY reupholstering office chair ...
- Pliers: Needle-nose is probably best here, you’ll be surprised how much you will use them.
How do I replace the cylinder on an office chair?
1:011:48How to Remove and Replace a Chair's Gas Cylinder - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis way when you twist it it'll actually grip the pipe or in this case the cylinder. And twist itMoreThis way when you twist it it'll actually grip the pipe or in this case the cylinder. And twist it out of there. So you just want to brace. It. Twist it and it'll come right. Out.
How do you remove a hydraulic cylinder from a chair without a pipe wrench?
If a pipe wrench is unavailable, you can unscrew the main bolts at the bottom of the seat to remove the mechanism from the chair. Then simply use your rubber mallet to tap the mechanism away from the cylinder, separating it from the chair.
How do you remove a cylinder from an adjustable chair?
First, you have to remove the base. If done correctly, this is really not that hard. Just lay the chair on its side, hold the base and pull toward you while giving a few good whacks to the bottom of the cylinder with a rubber mallet. It should slide right off.
Do all office chairs use the same cylinder?
If your chair is unable to adjust up and down, you may need to have the Gas Lift Cylinder replaced. All office chairs have an unique universal size and compatible with all office chairs sold in the USA/Canada. Outer cylinder has 2" in diameter, and the inner cylinder has 1.1" in diameter.
How do you fix a sinking office chair?
0:000:30Fix Your Sinking Desk Chair with These Simple Steps - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo fix a sinking desk chair. Start by sliding the plastic cylinder on the extendable part of theMoreTo fix a sinking desk chair. Start by sliding the plastic cylinder on the extendable part of the chair up or down so you can see the metal underneath.
How do you fix hydraulics on a desk chair?
How to Fix a Sinking Office ChairSTEP 1Measure Your Chair's Gas Cylinder. ... STEP 2Measure the Gas Cylinder's Stroke. ... STEP 3Purchase a Gas Cylinder Repair Kit. ... STEP 4Remove the Base from the Cylinder. ... STEP 5Remove the Old Gas Cylinder from the Mechanism. ... STEP 6 Install the Replacement Gas Cylinder in the Base.More items...•
How do you remove a gas lift from a chair?
0:071:24Removing the gas lift from an office chair - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe two tools will leader are a rubber mallet and a gadget like this an adjustable wrench ideallyMoreThe two tools will leader are a rubber mallet and a gadget like this an adjustable wrench ideally have one with soft jaws. This one happens to have fairly worn hard jaws now we need to adjust that.
Can office chair be repaired?
Luckily, many of the most common office chair issues can be fixed with a bit of elbow grease, your home tool kit and some office chair spare parts.
What is a gas lift on a chair?
A gas lift chair is a form of office chair that allows the user to modify their height in relation to the height of a desk, leading to an increase in comfort and ergonomic benefit.
How long do chair cylinders last?
You may have a chair for more than 10 years, and suddenly the gas cylinder begins sinking. At that point, the gas cylinders have reached the end of their life, and if you love your chair, inquire about ordering a replacement gas cylinder and installing the new one.
Are all chair cylinders the same size?
Five inch cylinders are standard for most chairs, but cylinders range from 4″-10″ depending on chair type. Most task chair manufacturers offer a choice between four, five, and six inch cylinders.
Are chair gas cylinders universal?
Yes, almost all the office chair gas cylinders are universal, having a diameter of around 2 inches and a height of about 10 inches. The difference between standard chair gas cylinders is how high the chair seat can rise.
How do you remove the nut from a hydraulic cylinder?
A simple socket set or spanner will quickly loosen standard nuts along with Pin punches, ball-peen hammer, circlip pliers. Stubborn or hard to remove piston nuts can be carefully heated to a measured temperature to release any Loctite or rust that is not assisting with the removal process.
How do you remove the lock ring on a hydraulic cylinder?
0:002:10How to Repair Snap Ring Cylinder - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a dead blow hammer tap. On a crossbar until the snap ring pops out.MoreUsing a dead blow hammer tap. On a crossbar until the snap ring pops out.
How do you free a stuck hydraulic cylinder?
Therefore, they won't fly down like they fly up without a load and can even get stuck so they won't move down at all. Try this: Spray the top of the cylinders with a good penetrating oil, and let it soak a few hours. Work the cylinder up and down. The penetrating oil will usually do the trick.
How do you remove a gas lift from a chair?
1:372:39OFM Presents How To Switch Out A Gas Lift For An Office Chair - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou this component from here you take a rubber mallet holding the gas lift simply tap. Around theMoreYou this component from here you take a rubber mallet holding the gas lift simply tap. Around the base. Until it pops off thus giving you nothing but a gas lift and a mechanism.
How to fix office chair sinking?
Is your office chair sinking every time you sit down? The best way to repair your chair is by replacing the cylinder. (There are quite a few DIY "quick fix" options, but those are only a temporary fix to the sinking chair.) So, what are the steps to replace an office chair cylinder?
Can you remove a gas lift from an office chair?
It's a fact that installing a new replacement gas lift is the easy part, but removing an office chair cylinder can be extremely difficult. You'll see youtube videos of people struggling with hammers and pipe wrenches trying to remove the piston from the chair seat, with no success.
How to remove a cylinder from a chair?
1. Separate the old cylinder from the base of the chair. To do this, turn the chair on its side and gently tap the base away from the chair with your rubber mallet.
Do office chairs sink?
The seats on most office chairs tend to sink after a few years of regular use. Don’t worry, there’s no need to buy a whole new chair! Chances are, the gas cylinder in your chair is the only part that needs to be replaced. If you purchased your task chair from OfficeFurniture.com, you’re in luck! All you’ll need to do is contact our customer service department at (800) 933-0053 and we’ll send a replacement cylinder out to you in a flash. Once you’ve received the new cylinder for your chair, just follow these simple replacement steps and your chair will be back to normal in no time!
How to get gas cylinder out of office chair?
Turn the office chair base with the attached gas cylinder column upside down and strike the gas cylinder column rim area until it pops out, freeing the base.
How to determine stroke of office chair?
First, lower your office chair all the way down and move it next to a wall or a door. Using the arm or top of back as a template, place a mark on the wall or door. ...
How to fix a gas cylinder hole in a car?
Remove the seat plate from under the seat. Place it flat on the floor. Spray some WD-40 around the space where the gas cylinder snaps into the hole. With the hammer, tap gently on the sides of the gas cylinder to help the WD-40 penetrate. Wait a couple of hours.
What is the diameter of a gas cylinder?
A standard office chair gas cylinder basically has two parts. The top part is called a gas spring and has a diameter of 28 mm or 1.1 inches. The gas spring is what holds the pressurized nitrogen gas and some oil for lubrication.
How to remove retaining clip from office chair?
Hold one of the base legs in one hand and apply pressure upwards as if you are lifting the office chair. With the hammer, strike the bottom of the office chair gas cylinder column that typically protrudes from the underside of the office chair base. Do not strike the center of the column where the retaining clip is located. Strike the rim area and rotate where you are striking. Continue striking in this manner until the office chair base pulls off.
Can you replace a gas cylinder in an office chair?
I am often asked by people which office chair gas cylinder replacement is right for their office chair. To answer that question, we must first determine if the office chair manufacturer used a standard cylinder. Unfortunately, the markings you see on the gas cylinder that you currently have do not list the exact specifications.
How Do You Change a Gas Cylinder on an Office Chair?
Unlike removing an old or damaged cylinder from your chair, replacing it with a functional one is quite simple.
How Do You Remove a Gas Cylinder from a Chair?
Before diving into the cylinder removal, collect the tools you need to get the work done. These include:
How to sit on an office chair?
Position your office chair upright, then sit on it. Sitting on the chair allows everything to fall into place perfectly.
What is the advantage of putting a chair back together?
The advantage of putting your chair back together is that you won’t spend as much time as when removing your cylinder.
What is the best way to remove scratches from a chair?
Rubber mallet or hammer. However, the former is a better option if you don’t want to leave scratches and grooves on your chair.
How to measure height of office chair?
Get in your chair, ensuring your feet are flat on the floor with your knees at 90 degrees. Afterward, keenly measure the distance from your knee cap’s base to the ground level. This distance is the height of your office chair’s seat.
How to prevent stains on desk?
Spread the papers or clothing on your working desk or the floor. This way, you’ll prevent the working surface from staining or impact damage. Besides, no stains mean you won’t have to struggle cleaning up once you complete your tasks.
Step 2
The base is connected to the chair either with retaining clips or nuts and bolts at its center.
Step 3
Place a pipe wrench on the gas cylinder, and spray it with WD-40 to lubricate it and make it easier to remove.
Step 4
Look up the chair's part number to find which gas cylinders are compatible with your chair.
Step 5
Be sure to follow the instructions for your specific gas cylinder, since installation procedures may vary.
Step 2
Use the rubber mallet to tap the base of the chair away from the seat of the chair. Do this until you can easily remove the base from the rest of the chair.
Step 4
Now that the hydraulic cylinder has been removed, you can replace it with the new one. Insert the bottom of the cylinder into the center of the chair base.
Step 5
Carefully lift both the chair base and the chair cylinder into the chair mechanism. The parts will then fasten on their own.
More From NBF
Do you feel good when you sit in your office? Is your office a place of productivity, focus and success? Or is your office uncomfortable, cluttered and a source of stress?
